1700+ JIUHB 52 week madness!

got my JIUHB0302 stable running at 2.376ghz 198*12 ..... at 2.1vcore volts ...... i finally decided to ignore bios temps as from the "feel" of the copperblock and water temps ... no way is it running at 60 to 70C .... and my copperblock is bolted so tight (i pity my mobo though) ..... and tried it it ran perfectly fine for several hours ran 3dmark sandra burn and played games for hours .... everything went okay =) ....... 1 thing did bother me is the voltages were already way off coz of the high vcore .... my +5V was 4.6 my +12V was 12.7v ...... but this generic PSU didn't crap out at all =) ............ i tried using MBM 5 winbond 2N---- temps were 20C lower ..... a bit too low ?? seems i can't really trust MBM 5 or USDM to give accurate temps ......

Nice oc. I see you got 8k3a like me, yes temps here are totaly off with tbred (I say more than 15°C rather close to 20°C) and the problem is not in software because at least in mbm you can use offset. But the temps are showing wrong even in bios pc health, so no solution here, only if some bios version would disable on die diode reading and just use socket thermistor instead.

morphling1 , i bought another generic 300w PSU .... and am planning to use both 300w PSU ...... 1 dedicated to the motherboard and the other one to the rest of the system ..... coz past 2.0 Vcore the voltages are way off the mark ..... would this help bring up voltages ...... i guess my mobo is a bit loaded .... GF4 and a SCSI RAID card is heavy burden on the PSU ...... i discarded the stock FAN of the GF4 and just placed a slab of copper then made a 3x60mm fans fitted into PCI slot 1 to cool it off directly connected to the PSU .... this helped a bit as the fans aren't sucking juice off the GF4 card or thru the mobo

my jiuhb 0302 (brown) has gotten to 2187 at 1.75 volts. It did 2004 at 1.6 with ease. All prime/FAH verified overnight. Just got it along with the 8RDA+ and TwinMos so I have been taking it slow while I burn in. I should know in a day or so where the ceiling is on this puppy. I have to figure out why I keep getting a no ram beep on post after 180 fsb so it could be longer. Hope not though.

BTW this is on air.

my 1700+ thoro "green" 0302 JIUHB @2,15 v with -10°C water
http://utenti.lycos.it/dimasweb/2535arit.JPG
bye

Really good result Dimas!

I think that with an 8rda that will grew up considering that your videocard can-t afford that fsb as you said to me last week...

it's all in the ram.:cool:

My CPU just arived. :(

I'm in deeeeeeeeeeeeeeeeeeeep §§§§.

Just look.

How bed is it doc?:confused:

Quote:

---

Originally posted by morphling1
Thanks
Currently 8RDA+ is definetly one of the best mobos, not that 8K3A isn't good, but the nforce2 just has too many pluses to ignore.

Oh yeah to you and GiJane, Welcome to xtreme :toast:

---

ya and nforce2 have also many cons..
You wont get any good results with it, without all the modding(vcore fix, vddmod and cooling on the mosfets and voltageregulator)

If you will by the board i hope u get a good one.

Hehe, that's understandable, the minute I come home with mobo it will go under soldering iron :D Cooling will be taken care off too.

morphling1 okay =) i will mod my in the weekend. Becuse i cant run lÃ:banana:ke this. Cant do over 190fsb or run 1.9V vcore. Unmodded this board realy sucks so hard that a 8k3a+ does much better =)
but even do i cant run high vcore i got my lite aiuga to post a wcpuid screen at 2147Mhz.

where is the extreme overclocks with this toys?

my 0302 JIUHB runs stable at 2310 mhz at 1.85V

256MB PC2700 (SAMSUNG) (M368L3223-CB3)
256MB PC3200 (SAMSUNG) (no-name)
256MB PC2700 (KINGSTON)(KVR333X64C25)

Witch one?

I need help on this. ASAP!

Tomorrow am going shopping and I need to know for what exactly.:confused:

If the first Sammy is rev C. chips (K4H560838C - TCB3) it will be very good. rev D are bad.
Sammy pc3200 are nothing special.
Kingston if it got BH-6 chips I would take that one. Then Sammy original module with rev. C chips

THX. I didn't get all of it but im preety sury that you would pic the sammy.

:p

JEEZ!!! just saw 1700+ AIUCB :eek:

gonna get one... along with my sammy 333 CLT-CB3 :)

Wow now that's interesting 1700+ that start with an A, so AIUHB should also start popping out, I gotta be on allert :D

this is mi 1700 thoro b....jiuhb 0252
http://digilander.libero.it/kiashan75/2699.JPG

Wow insane, this one is in my league :D What you use for cooling ?

wb...and h20.....

I have a week 3 cpu..

numbers:
AXDA1700DUT3C 9402837240109
JIUHB 0303XPMW

is this any good for oc? if anyone knows..

anybody got an XP1800+ t-bred B yet ??? they're starting to pop out here i think a JIUCB0251 ...... but i'm still trying to sell my XP1700+ T-bred A ...... i'll probably go for an XP1800+ T-bred B

knaSen,
Welcome to Xtreme :)
Test it & let us know ;)

tediber,
I don't see the point in paying the extra $ for how well the 1700's do :D

Got a 0302 JIUHB folding at 2490MHz 2,2V as we speak. Pretty sure it will do just over 2,5GHz at this voltage with water at 25+C. Booted up fine at 2,6GHz with colder water the first thing it did.