that would have been my second guess.......but i have some sammies HFCO by kingston here and the 2000 speed is 1.65v rated.Quote:
Originally Posted by Don_Dan
Printable View
that would have been my second guess.......but i have some sammies HFCO by kingston here and the 2000 speed is 1.65v rated.Quote:
Originally Posted by Don_Dan
According to Tom's, they did 1333MHz 6-6-5 at 1.9v and 1720MHz at 9-9-9 with the same 1.9v. Samsungs indead? It's difficult finding anything more on them :(
D9GTS/D9GTR came in 2GB double sided modules
Link to Tom's
I've never been a fan of Tom's and do doubt their results are the best achievable.
They're quite old modules, the review was done in September 2008.
Do you know offhand which Kingstons are definitely Hypers? I'd PREFER D9s as they just keep lasting (my kit lives between 1.95v and 2.2v with constant 24/7 load - WCG) but if the above turn out not to be D9s I'll settle for Hypers. Unless someone knows D9s that are still available, of course... 4GB 1600MHz 6-6-6 is what I'm wanting! - on a tightish budget. $200 is around the most I want to spend.
That sounds like 2x2g GTS.......they weren't as OC friendly as there 2x1 gig counterparts.Quote:
Originally Posted by Oj101
That test is the only one I found as well, all the results aren't really great and they aren't helping to determine which chips are used. :(
I know D9 came in 2GB stick flavour as well, but those are rare and insanely priced most of the time. Afaik I only know CSX using them on one of their kits.
There were some HCF0 rated for 1.9V by Kingston according to r00n's ramlist.
I've edited this post so many times I'm going to quote myself:
Quote:
Originally Posted by Oj101
The earliest thread I could find where HCF0 was mentioned to be used on new 4GB kits is dated August 2008. So I guess they are Samsung, but really not sure to be honest.Quote:
Originally Posted by Oj101
As far as I know, only the 2000C8 and 2133C8 ( 1.65V ) kits use Hyper chips at Kingston, maybe the 1866C9 ( 1.65V ) kit as well.
Of course that has to be the only RAM which costs MORE than GTX2s in South Africa :rotf:
KHX1866C9D3LK2/4GX, part number of the low voltage hyperx kit i posted earlier. Cheap and should be hypers :)Quote:
Originally Posted by Don_Dan
Of course they're almost $300 here :rolleyes:
1.35v is stock on the Kingstons??
Bummer :(Quote:
Originally Posted by Oj101
The 1866 kit is rated for both 1.35v 1866 and 1.25v 1600Quote:
Originally Posted by Oj101
Guy how good is this memory CMG4GX3M2A1600C6 - DOMINATOR GT I bought it for 245.00 from D&H. I am going to use it in my new rig....
Very good. 1800 6-6-6-18 around 1.68-1.7v.Quote:
Originally Posted by Yancey
More like 1800 6-6-6 1.71-1.73V but still good in my book.Quote:
Originally Posted by BeepBeep2
Are d9gtr sticks good enough for serious benching, or do I have to look for newer kits?:)
Depends on whether or not you're scared of voltage :p: It takes me 2.25v or more to get 850MHz 6-6-6
The question is if it's a voltage issue at all...
I wonder if TRP 4 helps on these chips? gtr sticks can do that:)
TRP 4 won't bring much over TRP 6 if anything. chew* said trp5 is slower in 32M than trp6. I'd rather stick with Hyper equipped ram than D9. Where D9 needs 2.25V Hypers can do the same or better with a mere 1.65V.
Hey, I've maxxed out every board I have except DDR3, I'm getting ideas now...
4.13v DDR? Check
3.375v DDR2? Check
2.?v DDR3? Hmmm... I wonder :hrhr:
Now you sound like M.Beier... :p: :rofl:Quote:
Originally Posted by Oj101
Hmmm...My 955BE dont like more sticks than two @ high mem clocks maybe i will try kill the third one with some voltage for fun :DQuote:
Originally Posted by Don_Dan
The difference is I go for frequency, not the record for "best performance on motherboard xxx using x.xxx VDIMM, x-x-x timings and a PSU originally commisioned by xxx - on a Friday" :)Quote:
Originally Posted by Don_Dan
Just an update to my previous Gskill Eco runs, got them to 1675Mhz 6-7-6-18-1T 1.575Vdimm
hows prime 95 blend cecil?Quote:
Originally Posted by Cecil
wow that's pretty good ECO's.. I haven't try CL6 on my ECO. Are these settings stable cecil?