Printable View
Alright mate, thanks for your input.
I promise thats last OT word...
I generally use dvd-drive for audio cd ripping (I love to listen to the music but I travel a lot- unfortunately my laptops dvd-bluray-xray-and whatever more formats it supports-drive is too slow and lacks audio data cache), sometimes for the games that need dvd to play (it's much easier then all that deamon tools stuff) but mostly to be able to reinstall my OS, which I'm right about to execute.
Thanks.
audio CDs => download mp3sQuote:
Originally Posted by MaynardX
games => even when you buy original game i would still use nodvd crack and similar and for MP you usually dont need DVD in drive
OS reinstall => usb key, much faster + you can easily replace it with new version
I personally would easily live without DVD drive...
Thanks It is up. Didn't realize I had 2 id's on this board boxer9999 and boxerQuote:
Originally Posted by boxer
SoLoR
You know, I'm the music lover, so using lossy formats in my case are no go (besides that sometimes I play music compilations from the usb stick on my stereo- for party purposes).
As far as gaming is concerned, I'm at the legal side here. so I always purchase games. Unfortunately in my country using cracks (and all other forms of game files manipulation) is illegal- I know it's sick, but there are more silly situations in my country, to be honest.
But considering using the usb for the OS installation- thank you for your suggestion, I really didn't know about this possibility. I'll try that one today (fortunately this method is legal in my country uff:)).
Any thoughts?Quote:
Originally Posted by DrTeal
Lower CPU volt and clock and try again no matter what LinX says. Should be something with voltage picks-regulator that does not work in my case
Flash your board with SoLoR's BIOS 1002-R3 or 1002-R4. These revisions have the latest CPU Microcode for your CPU and should improve stability.Quote:
Originally Posted by DrTeal
@MaynardX
I also use my DVD Writer to rip my audio CD's and just like SoLoR I'm using an Optiarc and my CD's are always accurately ripped with Exact Audio Copy.
Thanks Alien Grey, I'll head for on of the Optiarcs available at the moment. Guess those modern copys manage proper CD ripping. Hope soon get rid off MSR fails with new SoLoRs bios.
It could be a CPU issue too, reaching the higher tiers with 775 quads usually requires a fair amount of fine-tuning with GTL reference voltages, clock skews and straps. If I remember correctly there was a direct correlation between VTT and the CPU's GTL values which were different between the 65nm and 45nm quads. A quick Google search should find you the calculation for the GTL values based on the VTT.Quote:
Originally Posted by DrTeal
Before bothering with all of that, though, I'd try running a lower multiplier without changing anything else and then seeing if the problem persists first just to isolate the issue.
All of a sudden all DDR led and northbridge led lights are on and stay on when I booted today. This is after booting successfully for 3 years. The indicator says "CPU INIT" and does not change. I have been running OC of 4.50+ for a long time that I dont remember my exact settings. Can someone please help.
Thanks in advance.
Try taking out your RAM and putting it back in again, same goes for reseating your CPU and also check that your Graphics card has not come lose, in fact I would check the graphics card FIRST and then the RAM. then finally the CPU.
If all of that fails then as harsh as this sounds you may have to press the notorious BIOS default switch, but before pressing that see if you can boot with ONE stick of RAM.
John
Tried all of that and stilll showing all lights on. Maybe its time to replace the mobo. Its more than 3 years now.
I don't think that the board is dead. I think that you've got an electrical short or maybe the CPU is dead or there isn't enough power to run the CPU . If you're using a watercooling you could check for leaks and blow out the dust out of your case.Quote:
Originally Posted by patrickgerry
Thanks Alien Grey. I think you are right about the CPU. I am using vapochill and when I saw a lot of condensation around the CPU. I'll see if I can replace the CPU.
Here are my Q9450 latest 24/7 LinX stable settings, with 1002b-R4 bios:
My comment to the content above.Code:*Extreme Tweaker*
Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Setting [08.0]
FSB Strap to North Bridge [400]
FSB Frequency [460]
PCIE Frequency [110]
DRAM Frequency [DDR2-1226MHz]
DRAM Command Rate [2N]
DRAM CMD Skew on Channal A [Greyed Out]
DRAM CMD Skew on Channal B [Greyed Out]
DRAM CLK Skew on Channal A [Advance 50ps]
DRAM CLK Skew on Channal B [Advance 50ps]
DRAM Timing Control [Manual]
1st Information
CAS# Latency [5]
RAS# to CAS# Delay [5]
RAS# PRE Time [5]
RAS# ACT Time [15]
RAS# to RAS# Delay [3]
REF Cycle Time [Auto (52)]
WRITE Recovery Time [6]
READ to PRE Time [3]
2nd Information
READ to WRITE Delay (S/D) [8]
WRITE to READ Delay (S) [3]
WRITE to READ Delay (D) [5]
READ to READ Delay (S) [4]
READ to READ Delay (D) [6]
WRITE to WRITE Delay (S) [4]
WRITE to WRITE Delay (D) [6]
3rd Information
WRITE to PRE Delay [14]
READ to PRE Delay [5]
PRE to PRE Delay [1]
ALL PRE to ACT Delay [6]
ALL PRE to REF Delay [6]
Refresh Period [16120T]
DRAM Static Read Control [Disabled]
Ai Clock Twister [Lighter]
Ai Transaction Booster [06]
Pull-in of CHA PH1 [Disabled]
Pull-in of CHA PH2 [Disabled]
Pull-in of CHA PH3 [Disabled]
Pull-in of CHB PH1 [Disabled]
Pull-in of CHB PH2 [Disabled]
Pull-in of CHB PH3 [Disabled]
CPU Voltage [1.38v]
CPU PLL Voltage [1.56v]
North Bridge Voltage [1.61v]
DRAM Voltage [2.04v]
FSB Termination Voltage [1.38v]
South Bridge Voltage [1.05v]
SB 1,5V Voltage [1.50v]
Loadline Calibration [Enabled]
CPU GTL Voltage Reference [0.63x]
NB GTL Voltage Reference [0.67x]
DRAM Controller Voltage REF [Auto]
DRAM Channel A Voltage REF [Auto]
DRAM Channel B Voltage REF [Auto]
CPU LED Selection [CPU Voltage]
NB LED Selection [North Bridge Voltage]
SB LED Selection [South Bridge Voltage]
Voltiminder LED [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spred Spectrum [Disabled]
Cpu Clock Skew [Delay 200ps]
NB Clock Skew [Delay 100ps]
*CPU Settings*
CPU Ratio Settings [08.0]
C1E Support [Disabled]
CPU TM Function [Enabled]
Vanderpool Technology [Disabled]
Execute Disabled Bit [Enabled]
Max CPUID Value Limit [Disabled]
460MHz is max I can reach for 24/7, for 465MHz I'd need higher then 1.40V for both CPU and FSB Term Voltage, which is too much IMHO.
I guess these high numbers already are because of my CPUs low batch.
Unable to set LLC "disabled". Simply can't do, LinX stops upon error after few seconds run.
DRAM Controller and Channels Voltage set to "Auto", because it gives me about 0.4-0.5 GFlops more in LinX.
CPU and NB Clock Skews respectively 200 and 100 delay, for stability.
1002b-R4 bios is simply great, allows me for little higher frequency with same voltages, adding more stability. Great job, SoLoR.
Alien Grey, thanks for your last setup, I mainly based mine on it, especially considering DRAM Timing.
So I run LinX for 1.40h, because this is max time I usually spend working with my PC.
Unable to add image to the post: error 500.
Link to the screenshot below:
http://www.fotosik.pl/pokaz_obrazek/...909e69621.html
i dont know if my problem is isolated to just me, but i am only able to use R0. i have tried R1 thru R4 and it causes problems with the intel raid. seems like a problem only when the controller is in raid mode. I currently run three intel 40GB SSDs in a raid 0 array.
The only diagnostic information i have is that with R3 i got this right after the raid initialized right under the CTRL + I message: "Internal Error - PnP and PCI BIOS not present". On R1 R2 and R4 i either got artifacting and a hard lock when the raid initialized or any drives connected to the intel raid would not show up on the boot list. They did show up in the BIOS in the bootable device list though.
Am i doing something wrong?
Having some strange FSB termination issues. Board doesnt really want to boot with more than one memory stick, and even with one it is hit or miss. When it does boot and i cant get as far as the bios, it shows FSB termination as Red and down at 1.088v or around there. If i raise it up it seems to respond better but its very temporary, as in eventually it wont boot and i give it a rest, temps are all good and i'm just trying to get it to run stock speeds now, i tried two different processors, various ram and two power supplies all with the same result. Is this board just dead?
Have you tried resetting the board?
Yeah I've tried everything I can think of. Reset cmos. Reseat CPU. Swap out cpu, ram, change ram slots, swap out power supply. And also I tested the CPU ram and power supply on an old p5w dh deluxe and they all worked fine.
-- Sent from my Palm Pre using Forums
Then yes, it appears that your x48 has lost its go.
Most likely. The only thing i havent tried is to try and remove/reinstall the board to make sure there are no loose screws or standoffs. I have it limping along now with one 1GB memory stick (its favorite) all at stock speeds. Got a Sabertooth 990FX on the way to hold me over i guess until more 2011 intel chips and cheaper x79 boards are out.Quote:
Originally Posted by 3lfk1ng
Hi SoLor,
Could you please re-upload the 1002b-R4 bios?
Thanks in advance.
its still there....: http://hotfix.chris123nt.com/Asus.Ra...mula/Bios.MOD/Quote:
Originally Posted by James7410
off topic
Who's interested in Retro Gaming?
If you're interested in Retro Gaming and you would like to play your favourite arcade or console games you should have a look at the Dingoo A380. It's a cheap Chinese console that comes with a lot of emulators to play your favourite retro games. You can buy it from China on eBay. It has 4GB internal storage and an external MicroSD slot. The best thing is that the internal storage on the Dingoo A380 is also a MicroSD that can be replaced with a larger MicroSD.
I've bought one and upgraded it to 32GB. Enough space to store every single game ROM. ;)
Anyway if you're interested and would like to have hours of gaming fun and hours of discussions check out the Dingoonity Dingoo Technology A380 forum.
P.S.: Did I mention that it should be possible to overclock it to 500MHz. :D
^Or one could just get Hyperspin for free on your current PC.
Hyperspin is a beautiful front end that allows you to have an infinite number of emulators and all of your favorite games. It supports joysticks and game controllers and if you tell Windows to boot directly too it, it even has a way to launch PC games.