UnOfficial Asus Rampage II Extreme Thread

Printable View

Show 100 post(s) from this thread on one page

12-24-2008, 01:50 PM
theonlybabyface

My new 24/7. Not bad on air!!! :D

http://valid.canardpc.com/show_oc.php?id=469505
12-24-2008, 02:20 PM
ReVolut1on

Guys it seems that someone at asus forums solved his coldboot by flashing to bios 0805. Give it a try and let us know if it worked for you.

Edit: already two people got it working! :) sounds promising
12-25-2008, 10:10 AM
bmilos

Quote:

Originally Posted by theonlybabyface

My new 24/7. Not bad on air!!! :D

http://valid.canardpc.com/show_oc.php?id=469505

What are your temps?
12-25-2008, 11:16 AM
skypx

Quote:

Originally Posted by ReVolut1on

Guys it seems that someone at asus forums solved his coldboot by flashing to bios 0805. Give it a try and let us know if it worked for you.

Edit: already two people got it working! :) sounds promising

Yep, tried it, I even reset the CMOS, loaded defaults, nada. Seems the cold boot issue I'm experiencing refuses to go away.:mad:
12-25-2008, 11:40 AM
theonlybabyface

Quote:

Originally Posted by bmilos

What are your temps?

I'm quite warm. I'm idle in high 40's and load is in the high 80's. :p:
12-25-2008, 12:08 PM
ReVolut1on

Disregard my previous message.. They still got the coldboot when they tried to boot in the
Morning
12-26-2008, 06:02 AM
BringerOdeath

I need 1.544v to be 100% stable@ 4.2 ghz with HT off....I think I need to buy a different cpu and pawn this off on a family member!!>:)
12-26-2008, 05:17 PM
webwilli

i have found a little problem with the RIIE.

please test this:

Multi Auto (21 under load; Prime or cinebench)
BCLK 200
VCore 1.35 or more
HT on

if i (and two other people) set the vcore over 1.35, the multi goes down from 21 to 20,8x under load.
1.38 VCore for example give 20.5x.
Over 1.40 Volt the Multi is fix to 20.

My cpu temp is still perfect. Watertemp was 16 degress and cpu @ load 55 degress.

how can we override this problem? i would bench with 21x215 and 1.45 volt, but it is not possible.

is it a bios issue/setting?
12-26-2008, 06:04 PM
BringerOdeath

So, you have TURBO on I see and HT. If I leave HT off the multiplier stays at 21x and stays at 4.2ghz, no matter the voltage or temperature. If I turn HT on and I put a load of 100% on all the cores, it drops to 20x multi and 4.ghz. The temperature also doesn't matter...
12-26-2008, 06:32 PM
theseeker

Quote:

Originally Posted by webwilli

i have found a little problem with the RIIE.

please test this:

Multi Auto (21 under load; Prime or cinebench)
BCLK 200
VCore 1.35 or more
HT on

if i (and two other people) set the vcore over 1.35, the multi goes down from 21 to 20,8x under load.
1.38 VCore for example give 20.5x.
Over 1.40 Volt the Multi is fix to 20.

My cpu temp is still perfekt. Watertemp was 16 degress and cpu @ load 55 degress.

how can we override this problem? i would bench with 21x215 and 1.45 volt, but it is not possible.

is it a bios issue/setting?

WW,
Your English is fine!
Make sure you disable ASUS Temp Probe. I have found that it runs in the background and changes many settings based upon temps, not to mention that it is not accurate. I have noticed a big difference between AP and Real Temp. Just my 2 cents.

My poor attempt in Deutsch!
Stellen Sie sicher, dass Sie ASUS Zeitsekretärin-Untersuchung unbrauchbar machen. Ich habe gefunden, dass es im Vordergrund läuft und viele Einstellungen beruhend auf Zeitsekretärinnen ändert, ganz zu schweigen von denen das nicht genau ist. Ich habe einen großen Unterschied zwischen AP und Echter Zeitsekretärin bemerkt.
12-27-2008, 03:51 AM
Phil The Greek

Quote:

Originally Posted by skypx

Yep, tried it, I even reset the CMOS, loaded defaults, nada. Seems the cold boot issue I'm experiencing refuses to go away.:mad:

Same here:down:
12-27-2008, 04:47 AM
webwilli

Quote:

Originally Posted by BringerOdeath

So, you have TURBO on I see and HT. If I leave HT off the multiplier stays at 21x and stays at 4.2ghz, no matter the voltage or temperature. If I turn HT on and I put a load of 100% on all the cores, it drops to 20x multi and 4.ghz. The temperature also doesn't matter...

any idea how we can fix this?

Quote:

Originally Posted by theseeker

WW,
Your English is fine!
Make sure you disable ASUS Temp Probe. I have found that it runs in the background and changes many settings based upon temps, not to mention that it is not accurate. I have noticed a big difference between AP and Real Temp. Just my 2 cents.

My english is terrible, i know....

Where can i find Asus Temp Probe??

I don´t install any Asus Software. Only ACPI driver.
12-27-2008, 08:28 AM
fubarswe

In XP multi stays on 21 at full load or idle.., but in Vista it drops to 12.., 15,.., doesnt stay at 21 untill load is present...
This is with HT and Turbo on... C1 supp off..
12-27-2008, 09:54 AM
dejanh

Quote:

Originally Posted by BringerOdeath

So, you have TURBO on I see and HT. If I leave HT off the multiplier stays at 21x and stays at 4.2ghz, no matter the voltage or temperature. If I turn HT on and I put a load of 100% on all the cores, it drops to 20x multi and 4.ghz. The temperature also doesn't matter...

This is normal behavior. Gigabyte boards will not do this I believe as there is a mistake in their implementation of Turbo (i.e., it is always on)...turbo is supposed to be for single threaded apps only. The fact that this is not the case on most boards is a plain mistake in the BIOS (Gigabyte is the worst for it).
12-27-2008, 09:59 AM
Fitseries3

just turn off power saving features in windows power options. then turbo runs all the time.... pretty much.
12-27-2008, 10:30 AM
Chri$ch

Quote:

Originally Posted by dejanh

This is normal behavior. Gigabyte boards will not do this I believe as there is a mistake in their implementation of Turbo (i.e., it is always on)...turbo is supposed to be for single threaded apps only

That is wrong!

only the 20+2 turbo is for single threaded apps! 20+1 is on all 4 cores but normal
limited to 130W (Overspeed Protection) i think, but gigabyte and other manufactures
disable the limit that the 21 multiplier also run above this limit.
12-27-2008, 10:36 AM
webwilli

Quote:

Originally Posted by fubarswe

In XP multi stays on 21 at full load or idle.., but in Vista it drops to 12.., 15,.., doesnt stay at 21 untill load is present...
This is with HT and Turbo on... C1 supp off..

i have the bug in XP AND Vista.

Quote:

Originally Posted by fitseries3

just turn off power saving features in windows power options. then turbo runs all the time.... pretty much.

all power saving features are disabled.
12-27-2008, 11:06 AM
glenn37216

Hey Guys !
I just got this motherboard and I'm in the proccess of building my new rig . I was wondering on first boot should I leave the voltages on auto setting or set my ram , cpu to its rated volts? After a day or so of the it being up and running I'm going to overclock like it a mad man.
...What did you guys do on first boot..?
12-27-2008, 11:23 AM
fubarswe

Quote:

Originally Posted by webwilli

i have the bug in XP AND Vista.

all power saving features are disabled.

XP 32 default always 21.., Vista 32 turned power saving to performance = 21 24/7 (on this board...)

Ran this rather fast SP in XP.., HT on.., cooled by SS..

http://i39.tinypic.com/egsfgh.jpg
12-27-2008, 11:36 AM
Chri$ch

download this tool -> http://www.fileden.com/files/2008/3/3/1794507/Turbo.zip

open it and start prime to show us that 21 multiplier doesn´t go down to 20.

try with 21x200 and 1.45v and show us a screen :)
12-27-2008, 11:49 AM
webwilli

Quote:

Originally Posted by fubarswe

XP 32 default always 21.., Vista 32 turned power saving to performance = 21 24/7 (on this board...)

Ran this rather fast SP in XP.., HT on.., cooled by SS..

SuperPI is no problem.

But Cinebench, 3DMark06 and prime.

Run Cinebench and the Turbotool.
12-27-2008, 12:09 PM
fubarswe

Will test tomorrow.., have a feeling 06 will give me sum problems.., seen various results with same settings.., indicator that turbo falls of wagon.. :-)
12-27-2008, 12:34 PM
jasonelmore

Quote:

Originally Posted by fubarswe

XP 32 default always 21.., Vista 32 turned power saving to performance = 21 24/7 (on this board...)

Ran this rather fast SP in XP.., HT on.., cooled by SS..

http://i39.tinypic.com/egsfgh.jpg

That's one hell of a 920.

I want it. haha
12-27-2008, 12:35 PM
ReVolut1on

The overspeed protection should be removable. François Piedonel from intel has already stated a month ago that every motherboard manufacturer will include a bios setting called "CPU VR current override". Enabling this setting will make your CPU ignore all TDP limits. I know this setting exist on P6T so why would it not be on rampage?
12-27-2008, 12:44 PM
jasonelmore

Somehow i've lost HT on my cpu. When i enable HT and boot my computer it says i have 2 cores, 4 threads on cpu-z. Even with the bios values reset to default. I've reflashed my bios to the newest one and i still get 2 cores and 4 threads in CPU-Z. But when i go to the Device manager under CPU's it list 8 Intel 920's.

BUT when i open Cinabench up to do a HT test it only does 4 threads.

I've tried everything. I Reset everything to it's default values but I can't get my computer to use all 8 threads

Any Idea's? or do i have a busted chip?

Also..

When i disable HT CPU-Z will show me 4 cores with 4 threads like the pic i have attached. i will also post a picture with ht enabled.

http://i489.photobucket.com/albums/r.../th_Image1.jpg

http://i489.photobucket.com/albums/r.../th_Image2.jpg

Here it is with HT Enabled. Notice CPU-Z says 2 Cores and 4 Threads but the Device Manager says otherwise. But Windows and other programs still act as if there are only 2 cores and 4 threads.

Show 100 post(s) from this thread on one page