You'll like em. Running the 9600 Flex myself. Even though mine are the 2.35v versions, they only need 2.23v to run at 614mhz. If yours are the new ones, don't go shovelling 2.3v+ into them. The newer ones are different IC's and run at a lower Vdimm.Quote:
Originally Posted by runmc
Perhaps "cutie's" got his mouth stuck on that nice cold evap you sent him :D
im sure ive seen that picture before. holding sum1 to ransom :shrug:Quote:
Originally Posted by runmc
Right on every point there man. 2.1 would be the max I would try if the newer ICs are in place.
By the way, I toilet at air 1:1 to no runmc that I was going to make sure the ones I had would run the numbers he wanted. So far 1:1 with this POS processor I could only validate to 524 or 1048DDR. Not sure that would help him but on second thought they might have since he was under phase and I was airing it out. Think he was mostly unable to 'boot' at all without C1. Dang it. :yepp:
Quote:
Originally Posted by kitfit1
Umm, Exactly what happened to DFI Club? I've tried a few times to get there, and I keep getting a page with some babe on the right, 1 of the wives? J/K :DQuote:
Originally Posted by kitfit1
But all kiddin aside, what gives?
Larry
Hey, not sure if this is the place to post this, but I'm new to Overclocking. Specs are in my sig. I'm trying to setup my comp to run 3.0Ghz [333*9] and I'm trying to get the RAM to run 1:1 but I don't understand the bios well enough to be able to. Would someone here be able to help me or is this the wrong place to ask this?
http://img149.imageshack.us/img149/4707/cpubm9.jpg
http://img156.imageshack.us/img156/1931/ramto2.jpg
DRAM Speed - 333/667
Thank you. So I'm assuming when you increase the clock you increase the ratio? or is it just as long as thats the overall FSB that you leave it with that? [sorry for the newb questions]
You don't have to increase the ratio. Try leaving it at 333/667 (1:1) and raising the FSB. You'll see that the ram speed changes automatically based on the fsb you set.
In other words, when you raise the fsb you raise the freq of the ram. The ratio stays put as you set it.
3/17 bios are now on the official bios page. still corrupted when i'm trying to extract :(
Looks like it's all sorted and back to normal this morning :up:Quote:
Originally Posted by Big Lar
Great, kinda missed it :)Quote:
Originally Posted by kitfit1
Larry
The OCZ PC2 9200 came in today. It looks like it was Crucial Balistics that was holding me back at 1/1 (333/667)
I made some major improvement but fell just a little short of my goal. (Wanted to get into the 8 sec Club) It's misting here today, and I think was mobo was getting wet. It started crashing left and right.
Thanks for the help Praz and RGone - you were right - is was the ram ;)
Intel E8400
DFI Lan Party LT P35
Ocz PC2 9200 @ 1/1 - 5 5 5 15
Phased cooled
SWEET! Keep trying, it's so close.
Any advice on clocking 4x2gig on this board? My EVGA 780i board could get this ram to 1000 5-5-5-15 @ 1.90v, but the DFI seems to balk at anything over 900. It's the cheapo A-data from Frys. And, yes, I do use all 8 gigs.
Thanks!
@bent
try bumping your NB voltage a few notches up. Also check your subtimings they may be too tight for your settings.
Tried this. About the only think i could find in regards to overclocking 8 gigs was to raise the TRFC anywhere from 52 to 56 when going over 900. I've tried bumping everything up a notch or 2 including taking the memory from 1.85 to 2.1 with worse stability after 1.97v. I've set the base timings and TRFC with everything else left to auto. Any help out there?
@runmc: what's your settings on those?
Pretty much just like this. Definately time to make a couple of changes to go higher.Quote:
Originally Posted by emoners
Code::
Genie BIOS Settings:
Genie BIOS Setting:
Exit Setup shutdown....................... - Mode 2
CLOCK VCO divider......................... - Auto
CPU Clock Ratio........................... - 9 X
CPU-N2 Ratio.............................. - Disabled
- Target CPU Clock........................ - 4500 MHz
CPU Clock................................. - 500 MHz
Boot Up Clock............................. - Auto
DRAM Speed................................ - 333/667
- Target DRAM Speed....................... - DDR2 1000
PCIE Clock................................ - 100 MHz
PCIE Slot Config.......................... - 1X 1X
CPU Spread Spectrum....................... - Disabled
PCIE Spread Spectrum...................... - Disabled
SATA Spread Spectrum...................... - Disabled
CPU Feature:
Thermal Management Control................ - Disabled
PPM(EIST) Mode............................ - Enabled
Limit CPUID MaxVal........................ - Disabled
C1E Function.............................. - Disabled
Execute Disable Bit....................... - Disabled
Virtualization Technology................. - Disabled
Core Multi-Processing..................... - Enabled
Voltage Setting:
CPU VID Control........................... - 1.50V
CPU VID Special Add....................... - Auto
DRAM Voltage Control...................... - 2.35V
SB 1.05V Voltage.......................... - 1.15V
SB Core/CPU PLL Voltage................... - 1.55V
NB Core Voltage........................... - 1.50V
CPU VTT Voltage........................... - 1.20V
Vcore Droop Control....................... - Disabled
Clockgen Voltage Control.................. - 3.45V
GTL+ Buffers Strenght..................... - Strong
Host Slew Rate............................ - Weak
GTL REF Voltage Control................... - Enabled
CPU GTL 1/3 REF Volt..................... - 80
CPU GTL 0/2 REF Volt..................... - 80
North Bridge GTL REF Volt................. - 80
DRAM Timing:
Enhance Data transmitting................. - Fast
Enhance Addressing........................ - Fast
T2 Dispatch............................... - Auto
CAS Latency Time (tCL).................... - 5
RAS# to CAS# Delay (tRCD)................. - 5
RAS# Precharge (tRP)...................... - 5
Precharge delay (tRAS).................... - 15
All Precharge to ACT...................... - AUTO
REF to ACT Delay (tRFC)................... - 24
Preformance LVL (Read delay).............. - 8
MCH ODT Latencey.......................... - AUTO
Write to PRE Delay (tWR).................. - AUTO
Rank Write to Read (tWTR)................. - AUTO
ACT to ACT Delay (tRRD)................... - AUTO
Read to Write Delay (tRDWR)............... - AUTO
Ranks Write to Write (tWRWR).............. - AUTO
Ranks Read to Read (tRDRD)................ - AUTO
Ranks Write to Read (tWRRD)............... - AUTO
Read CAS# Precharge (tRTP)................ - AUTO
All PRE to Refresh........................ - AUTO
Clock Setting Fine Delay:
Ch1 Clock Crossing Setting................ - More Aggressive
DIMM 1 Clock fine delay................... - Current[1486]
DIMM 2 Clock fine delay................... - Current[ 612]
Ch1 Command fine delay.................... - Current[1012]
Ch1 Control fine delay.................... - Current[ 562]
Ch2 Clock Crossing Setting................ - More Aggressive
DIMM 3 Clock fine delay................... - Current[1337]
DIMM 4 Clock fine delay................... - Current[ 524]
Ch2 Command fine delay.................... - Current[1086]
Ch2 Control fine delay.................... - Current[ 449]
Ch1Ch2 CommonClock Setting................ - More Aggressive
Ch1 RDCAS GNT-Chip Delay.................. - Auto
Ch1 WRCAS GNT-Chip Delay.................. - Auto
Ch1 Command to CS Delay................... - Auto
Ch2 RDCAS GNT-Chip Delay.................. - Auto
Ch2 WRCAS GNT-Chip Delay.................. - Auto
Ch2 Command to CS Delay................... - Auto
Read delay phase adjust:
Channel 1 Phase 0 Pull-In................. - Auto
Channel 1 Phase 1 Pull-In................. - Auto
Channel 1 Phase 2 Pull-In................. - Auto
Channel 1 Phase 3 Pull-In................. - Auto
Channel 1 Phase 4 Pull-In................. - Auto
Channel 2 Phase 0 Pull-In................. - Auto
Channel 2 Phase 1 Pull-In................. - Auto
Channel 2 Phase 2 Pull-In................. - Auto
Channel 2 Phase 3 Pull-In................. - Auto
Channel 2 Phase 4 Pull-In................. - Auto
Your TRFC at 24 is quite aggressive.
Good when a plan or suggestion comes together. I had been reading too many posts about issues with Crucial to just set on it. My problem was that like a dunce I was trying to push the set I had intended to send to you, to the ram speed you wanted to reach...not ever considering that you were on phase and lame me was still on air. You beat me to the 'buy' button. Hehehe.
Truth, that is pretty good with nearly in the 8's at only 4500mhz. You must be getting some serious working bandwidth to be that low in the 9's at only 4500mhz.
Congrats to you man and glad Praz and I had a small clue to add to your mix, you done good.
Quote:
Originally Posted by runmc
What you got in light blue in this menu that you are not showing? Five digits that is in light blue at tops of those two groups of settings?
Code:Read delay phase adjust: ? - ? - ? - ? - ?
Channel 1 Phase 0 Pull-In................. - Auto
Channel 1 Phase 1 Pull-In................. - Auto
Channel 1 Phase 2 Pull-In................. - Auto
Channel 1 Phase 3 Pull-In................. - Auto
Channel 1 Phase 4 Pull-In................. - Auto
Read delay phase adjust: ? - ? - ? - ? - ?
Channel 2 Phase 0 Pull-In................. - Auto
Channel 2 Phase 1 Pull-In................. - Auto
Channel 2 Phase 2 Pull-In................. - Auto
Channel 2 Phase 3 Pull-In................. - Auto
Channel 2 Phase 4 Pull-In................. - Auto
Running an X3350 is interesting on this board. I need high NBcore voltage and high VTT I can get it to run P95 small ffts for an hour. If I run blend it fails immediately. I would like to blame the memory modules (Crucial DDR2-667 D9GMH) but I also think the NB is being stressed to the extremes here. I had an X3210 that I could run 24/7 at 3.8GHz with only small bumps in the above mentioned voltages and 1.475vcore. To get 3.6GHz with this board and the X3350 I need only 1.296vcore but 1.61vNB and high VTT (sorry, don't remember the value) and still it will run small ffts fine but the blend kills it. It feels like the CPU itself is stable but the NB/memory is a killer.
try relaxing performance level to >8 and make sure the first two option in memory timings are set to FAST or lower (NOT TURBO!)Quote:
Originally Posted by sofarfrome
Ckeck out the MHZ in "SetFSB" in the picture :up:Quote:
Originally Posted by RGone
http://www.xtremesystems.org/forums/...1&d=1206740631
Having issues with crossfire people. 3d06 scales accordingly but Source based games run worse with crossfire enabled.