@starostise, "i think my cpu is awesome regarding temp and voltage". It is, that's fantastic.
@CompGeek, that would be tough. Maybe you could offer to pre-test them.
Printable View
@starostise, "i think my cpu is awesome regarding temp and voltage". It is, that's fantastic.
@CompGeek, that would be tough. Maybe you could offer to pre-test them.
little better :)
cpu @ +17°C
http://membres.lycos.fr/starostise/K...C_cpu-3588.PNG
http://valid.x86-secret.com/show_oc?id=84404
Is this suicide shot or Super PI 1m stabel ?
suicide shot.
hi,
i need some help with san diego 3700 overclocking.
first my config:
- san diego 3700+ on aircooling
- dfi nf 4 ultra d
- 2x512mb twinmos bh-5 old (doing ~265mhz@3,3v and ~272mhz@3,53v)
- msi 6600gt pcie
- lc power 550w powersupply (20-pin)
i have 2 destinations, >3000mhz on cpu and >260mhz@2,0 2 2 x on my rams
so i am trying following settings, they are 4 to 5 h prime and super pi 32m stable:
11x313mhz @1,48-1,5vcore with 166 divider -> 260mhz on rams
so far, everything is ok, but when i startet looping the first 3 tests of mad onion 3dmark 2001 , the system crashes between 1 to 5 minutes.
(i never tried higher versions, perhaps i should ...)
it seems 3d/pcie load crashes my system.
i think, my temp's seems to be okay, 40-42° C load on cpu, 42-44°C load on chip? the volts of my powersupply seems to be okay, too.
i am playing with open case, extra cooling on ram, northbridge, graphic card, and so on to locate the problem, but nothing.
i am playing with different bios versions and spent a lot of time on optimizing all the memorytimings, rising ltd and chip volts .1v but there is no satisfying result.
so i need help and suggestions, especially from people with the same settings or from people with same problems.
by the way, are there pcie settings in the bios , which relieve or stabilize my system?
sorry for my horrible english, i am from germany and i know i have to improve it ;-)
(when i am in the false section, please let me know.)
H.
just started to OC it last nite and this is what I've gotten so far. Will have 3.0 and 30000 by this week end.
http://i20.photobucket.com/albums/b2...h_5845c412.png
http://i20.photobucket.com/albums/b2...th_29476-2.png
http://i20.photobucket.com/albums/b2...h_000_0368.jpg
http://i20.photobucket.com/albums/b2...h_000_0386.jpg
http://i20.photobucket.com/albums/b2...h_000_0374.jpg
http://i20.photobucket.com/albums/b2...h_000_0377.jpg
Nicely done my freind :toast:Quote:
Originally Posted by starostise
Nice one! Any benches? :)
If I buy either an A64 3700+ or an Opteron 146 today, which one will have a better chance to hit 3GHz on air? (under ~1.60V, preferrably under 1.55V)
3700+.
nope.Quote:
Originally Posted by funkflix
mem controler is semi-dead due to a bad insulation, so i do not have dual channel and 1T mode any more :(
3700+. After a couple hours of attempts, I was able to finally run this by changing the drive strength to a combination it liked. http://img449.imageshack.us/img449/8...s5hr6rn.th.jpg
http://img458.imageshack.us/img458/8...s4hr0jq.th.jpg
Now test again with large FFT's and priority @ 10 ;)Quote:
Originally Posted by coop
Heya,
I own a 3700+ 2.2ghz sandy. I have successfully overclocked it to 2.7ghz on stock cooling and heatsink. It passed a 16 hour prime blend test. So i guess its pretty stable :) Just one problem. Under full load such as prime. the temps can go as high as up to 50+*C. Probably because im using stock heatsink. Is there any heatsink and fan you would recommend to get this baby running cool again? Please let me know which heatsink will be good to pick up.
Thanks
Mike
hi
ninja and noiseblocker SX2
keeps my opty at 40ºc 1,52v full load
a bit expensive but a great cooler....
"Now test again with large FFT's and priority @ 10 "
Sheeet my friend, my ram is bulletproof. :slobber: Tried, tested, and proven many times.;)
I am fortunate to have the 2 set I do and to have never sold them.
Ok, but using small fft's stresses your CPU less then using large. Just run the "real" Prime95 and choose maximum heat.Quote:
Originally Posted by coop
A few days ago I've tested my sandy 4000+ the first time with a mach2. The cpu was about -20. But the result was there
http://i49.photobucket.com/albums/f2...cking/M225.jpg
SS was about 3.6GHz
This is my stepping:
ADA4000DAA5BN
KABYE 0538GPMW
1334407150474
screen @ 3604MHz for 4°C
http://membres.lycos.fr/starostise/K...604-dod-4C.PNG
valid: http://valid.x86-secret.com/show_oc?id=87641
it screens @ 3590 for 17°C too so between 4° and 17° it could do better certainly :D
hello guys, ive just recieved my new cpu Athlon 3700+ ccbwe 0549 upmw stepping. been running prime for the last few hours to burn it in. just wondering what sort of overclocks u have got with my stepping
cpu @ +12°C idle
http://membres.lycos.fr/starostise/K...38-dod-12C.PNG
http://valid.x86-secret.com/show_oc?id=90342
coldbug @ +11°C for 330 HTT
time to get my results in here-->
3100MHz suicide
http://img89.imageshack.us/img89/3563/3100mhz9qs.jpg
3008 SuperPI32M stable
http://img164.imageshack.us/img164/9...3008mhz4pq.jpg
Thats all I have here, but thats because my rig is in germany whereas I am in the US.
I think it could go higher, but it was limited by my mobo and cooling, before it was on the eVGA 133-K8-NF-41-AX board (not too bad actually) and a Freezer64 non-pro, but now with the DFI and the SI-120, I am hoping around 3GHz stable! Now if my mem would go it :stick:
CPU : San Diego 3080MHz @ 1.440V
WC : PowerX + Eheim 1250 + Black Ice eXtrem
Stepping : I don't know, buy without IHS ;)
http://mardok.ovh.org/screen/sp2k4/S...308_1.440v.png
3700+ kacae 0605 apgw
i can bench @3g post @3.1 but i can only get 2.9prime stable i had it running max heat for 14 hours till we had a power cut;)
Hello,
Can anyone help me, i have a 4000+ (KABYE 0541GPMW ).
My PC,
Asus A8N32SLI
Gskill HZ PC4000
Enermax Liberty 620W
Help me...