Nice list :)
BTW I will be putting my 3800+ under a mach 1 @r404 this weekend, hoping for some good results, something like 3,3 GHz 24/7 stable..
Printable View
Nice list :)
BTW I will be putting my 3800+ under a mach 1 @r404 this weekend, hoping for some good results, something like 3,3 GHz 24/7 stable..
these 06's sure are quality! I only see one cpu under 2700mhz using more than 1.5v, that is mighty impressive.
Looks like the 0601 UPMW club is doing pretty good as well.
Cheers for that, jimi.
Nice list stone cold. That took alot of reading and searching I bet.
Hmmm lots of failed FX60's?
Well guys i think i've got the worst 06 3800+ EVER
ordered one from newegg... expected 0607, got 0603
LDBHE 0603 WPDW...
I started overclocking and could tell right away it was bad, 2.7 with 1.4v couldn't even get into windows. 2.75 with 1.5v failed prime instantly. 2.8 Ghz with 1.6v locked up right after loading windows... right now i'm playing with 2.6 Ghz with 1.4v.
2nd worst socket 939 CPU i've ever owned (and i've owned a LOT).
found an interesting one where i hooked you up with your other one Absolute.
CDBHE 0608 FPMW batch 500 ish
Stone cold the new one is 0605 XPMW No results as its not here yet.
The 0601 XPMW @ 3347 did that 1M at 1.62 did a 32M at 3.2 with 1.6v max windows 3508 and usable with 1.75v havent tested further.
Don't forget my 24/7 chip LDBHE 0539 RPMW does 3.0 24/7 stable in prime pi32m and everything else 1.6v
benchable @ 3129 1.65v
chew*, I'll amend the list (and add a couple more).
Really, it's an ad-hoc list to give us a rough idea. Unlike the Official x2 OC table (which needs 32M minimum as evidence), I've taken every scrap of info (verified or not) and stuck it in. There are surprises; quite a few 0606 chips doing 2800 /1.4v or so on air.
I'm still betting that LDBHE finished on week 0607 and that we'll only see LDBFE after that. If anyone sees a LDBHE 0608 or later, shout.
@situman: No, not failed FX-60s, different core.
so far seen CDBHE on week 0608.Quote:
Originally Posted by stone_cold_Jimi
its looking real good so far. i averaged all the clocks from the list, and it comes out to 3g's even. or 3000.6071428571428571428571428571 if you want to get technical. i can't wait to get mine its gonna be a blast.
Mine is a LDBHE.Quote:
Originally Posted by stone_cold_Jimi
I try to reach 3 GHz but one of the two cores did an error after ~40 min.
@Babbsack: What cooling?
under water !
mine's pretty much stabilized at 2.75 and 1.4 volts for 24/7 purposes. It's LDBHE 0601TPMW N chip.
Superpi 1M finishes at 31.5 seconds. Fastest chip I've ever had but temps are scary compared to my last Opteron 170. 33 Idle and 47 load using the opteron heatpipe hsf vs 27 idle and 41 load for the 170 at 2.6 and 1.42 volts.
look @ your TcasemaxQuote:
Originally Posted by freddy418
I bet your X2 is around 69/71c 89w and you Opty 49c/35w
Guys, my LDBFE 0607 XPAW is looking to be possibly the worst S939 chip of the last year. I went to prime 2.5GHz last night at 1.45v and the computer froze very early on. It's a T chip and a low batch, I figured I'd get atleast 2.8ghz....this is just horrible.
I've been playing with the same stepping chip for the past two days and I have to agree. AVOID THIS STEPPING!Quote:
Originally Posted by EnJoY
thanks for the heads up on the LDBFE 0607 XPAW, was going to pick one up locally today to replace my 165 @ 2.7 . The other choice is a LDBFE 0608 UPMW "T" ......decisions.........
go for the UPMW.
"N" chip
If you guys can update the list, right now I'm priming 2600ghz w/ 1.4v .. that's the highest i'm going to raise it for 24/7 purposes and because my ram hits a wall at around 263... The temps on load are 43C and idle is 23C. Pretty decent chip (imo), I speculate a good w/c rig could bring out the 2800ghz in this puppy, though I doubt 3ghz (volt limited).
2500 needed 1.35v
2550 needed 1.375
2600 needed 1.4v
Whoah! Before you write it off, have a serious play with your RAM settings. My LDBFE 0607 UPMW is possibly the pickiest chip w.r.t. vcore and memory settings that I've ever owned... and a couple of day's solid tweaking got me SPi 4M stable at 3200 /1.65v under phase. I always think "lockups=memory+controller", time to tweak.Quote:
Originally Posted by EnJoY
If that doesn't work, then yeah, it's dread.
Well, after fighting a corrupt video driver all damn day long, I finally am up and going again. I popped my ihs off a little bit ago, and I have seen a very significant gain in temps. Whereas, before, I couldn't prime above 2950, no matter the volts due to heat, I am now priming at 3000 @ 1.5v and my load temps are 38C. They used to be 39 to 40 c @ 2900 and 1.4v.
Will post a screenie if I pass 1 hour.
system froze after 27min and change. I just raided ldt volts to 1.3, gonna see if this helps. Temps are still 38c loaded. This is the best chip ive ever owned.
same problem...system freeze sometime during prime (or blank screen)
Here's 3.0gig 30min. dual prime
http://img224.imageshack.us/img224/5...custom1.th.png