Nice! My store has again 144 on stock and they will send it to me today.
Steppings are all CABYE 0536. At least i'm not getting the worse (i hope) :)
Cannot wait to put my hands on it :D
Printable View
Nice! My store has again 144 on stock and they will send it to me today.
Steppings are all CABYE 0536. At least i'm not getting the worse (i hope) :)
Cannot wait to put my hands on it :D
what about this serial? Witch is the best? What can I expect from this cpu?
CABYE 0536GPMW
CABGE 0534
CABYE is better....expect somewhere marginally below 3GHz.
with witch kind of cooling?Quote:
Originally Posted by Vapor
thanks
Decent air I would guess. Some will be worse and some will be better of course...
Yes sure, just to have an idea thanksQuote:
Originally Posted by Vapor
Here is my 144 0530 APMW 0081er Batch at prime and 32M and 1M
Its without heatspreader. Under water.
the RamMHz at 32M is an error, it runs at 200/140
http://mitglied.lycos.de/freestylerc...6V%20prime.JPG
http://mitglied.lycos.de/freestylerc...56V%20@32M.JPG
http://mitglied.lycos.de/freestylerc...Pi%2025sec.JPG
free
what mobo are you using?
What cooling? :slobber:
And I'm 99% sure he's using DFI as SmartGuardian doesn't play well with other boards from my understanding.
freestylercs: Where and when did ou buy it? I may buy one in Germany...
man wish i had a CABNE sweet 3.2ghz freestylercs!
Opteron 144 CABYE 0536 GPMW run @2906mhz at 1.52v
1M = 28.235S
8m = 5m 11.329s
32M = 24m 54.766s
Quote:
Originally Posted by freestylercs
:rolleyes: :slap:
Quote:
Originally Posted by Vapor
yes it s a DFI SLI-DR.
Normal watercooling: Tripple radiator.
@Mats its one of the first 144er, here I bought this Opteron:
ebay.de
less than 200 €.
to cut the heatspreader is the best i´ve done.
(sorry for my english??)
free
There's A LOT of variation in water....for instance, mine's no better than a Big Typhoon while his is way ahead of it. :fact:Quote:
Originally Posted by gulp35
Doh :(. Where did you get it?Quote:
Originally Posted by mbm
Quote:
Originally Posted by Vapor
If I loosen the preamble or MAL in the BIOS the computer won't boot either. I can tighten them though. SInce I have DDR500 theses shouldn't be topping out at 215 right? Here is my tweaker shot...
Leave MAL at auto and set PA to 7.5ns.....it doesn't boot on an Opty?! Hmmmmmmm, let me think about this one--this is new.
EDIT: just looked at your tweaker shot and it's running a PA of 7.5ns, you should be good to go I think.
yeah. Seems strange to me....but i have no idea what the problem is. Ihave tried changing one at a time, both together, nothing works.
Don't change them in Windows if you can't, somethings just don't like to be changed....anyway, keep them at 8ns and 7.5ns respectively, most people have had their best OCs with those values.
Mine won't boot with read preamble at 7 either, i've heard it's a bios issue.
With bios 704-2bta it should be possible.
hey uhm if i post pics of my optie... i should block out the serial number in 3rd line? the one that tells g50 and 0120 batch? but block out the rest? why?
just a note. backed it down to 280x10 with mem on 183 divider
but ass soon as i get some rest so read tomorrow ima start the testing from scratch. i'm gettin higher temps than my winnie of course... and i think i mounted the storm block better this time, but i just dunno what to do. hmmz.
Quote:
Originally Posted by Zeus
I think I tried it with 704-2bta but I can't remember....just recently backed down to 603. Hmmm...maybe I will give it a shot, right now I am testing single sticks. How long will OCZ accept RMA's for?
Quote:
Originally Posted by Vapor
My PA is booting up at 5ns now... and my MAL is at 7. Not sure why it changed.
This CPU amazes me more and more every day, it passes OCCT test at 3000MHz with a lousy 1.39V. :eek:
Watercooled in an 20C ambient.
http://www.xtremesystems.org/forums/...id=38782&stc=1
I have to be honest, this is single channel cause one of my RAM modules broke. :(
Hey Zeus,Quote:
Originally Posted by Zeus
Will be interested to see if you have a difference in OC once you are running dual channel again. Oh and I keep seeing you mention the voltage tht your CPU needs. Even though the software u use reads 1.39v I very much doubt tht the CPU is being given 1.39v. Only one way to find out (which we already discussed) but I imagine tht your brd is like the other DFI boards then your 1.39v is probably more like 1.44-1.48v! Big difference ;)
You're right about the voltage, i set 1.425V in bios and in windows it shows at 1.39V
Still, it's pretty obvious these cpu's run very fast at very low voltage.
Have to see about DC, it might need a tad more voltage, i will report back as soon as i have new RAM. ;)
Quote:
Originally Posted by Zeus
Tried the new BIOS and it doesn't work either. The only way I can loosen those timings is if I use a divider. In other news....I hit 3ghz on 1.43v, or whatever it really ends up being. Load temps 34c
Well, here is a prime pic of my 144er. For prime i had to run with 200/166er, and my BH5 are at the end.
http://mitglied.lycos.de/freestylerc...Primelarge.JPG
free
Freestylercs, is that the CPU from ebay? :D
Can you do OCCT at that speed/voltage?
I got my opteron 148 from Ewiz earlyer this day
its a Cabye 528 GPMW
so far i have reached 3125 as max clock for 3dmarks and 1M super pi
This is on water with the IHS on (i will get a LS in a couple of days and i am not sure if the evap can make contagt to the core if i go naked)
Super pi 1M at 26,422 sek @ 3.125mhz :banana:
3Dmark01 40.288marks @ 3.120mhz :banana:
it is prime stable at 3ghz @ 1,6 v.core i wont go further because it runs very hot
Do they top out even if you drop the main bank of timings to 2.5-4-4-8? What voltage are you running them? The rest of the timings should be ok, nice 3ghz btw :)Quote:
Originally Posted by foofreaknfighte
Mine arrived today.
Its a 148 I bought wed 12 on compumusic.
CABYE 0528GPMW
the last 4 digits is 0100...
tomorow I will test... I was especting a cabne , the guys from compumusic told me that ... but I was lucky it wasn´t a bad stepping.
Going for my non-clockgen 3ghz screenshot....I am a little worried that my pwm temp is high, its TOUCHING 60c every now and then :eek: Is that ok? And yes my memory tops out no matter what the timings are it seems. I currently have the RAMv set to 2.7, but I have tried 2.6 and 2.8 as well. I really can't believe thats its a problem with the sticks.
60C is too high. Anything above 55C and your chip is in the danger zone. I don't like it to go above 50C personally.
What's it's maxTcase?
i'm starting to suspect some issues of contact between the IHS and core.
i got my 148 CABYE today as well and even at 1.45 volts, mine is starting to hit 60C's with OCCT stability test. (2.8 ghz).
with my 0517 SD 3700+ it never hit above 53C's with 1.6 volts... or do these opterons just run warmer???
Wow that is high, thats a reading from the area around the chip that controls vcore. Try to get a fan blowing on the heatsinks on the mosfets. Maybe you're having a problem with your board? You have all 4 power connectors plugged in, correct?Quote:
Originally Posted by foofreaknfighte
He said PWM, not CPU. The PWM can do higher temps than the CPU, don't know how much though.Quote:
Originally Posted by xenolith
Quote:
Originally Posted by Runner
Yes, I have all four power connectors in. Is it possible that my board is causing the problem with my ram? Cus I am thinking about RMA'n my ram...or putting my p4 system back together to see how it does.
Ahh, sorry. IMO, 60C is still too high for PWM. But I'm a cooling freak anyway. :)Quote:
Originally Posted by Mats
I'm thinking yes and yes. These are rated at 85w vs. 67w that we've all probably been running, but if people have been getting a 10 degree drop by removing the IHS then I suspect that your first assumption may be correct as well. I can't see the IHS causing that much of a temp difference unless it wasn't making good contact.Quote:
Originally Posted by shimmishim
BTW, mine's running a little warmer than I expected too. I even reseated the evaporator last night to rule out the possibility of a bad install.
Got my CABNE 0528GPMW from compumusic today :) I think mine would benifit the ihs removal but it doesnt break 48c load on good watercooling.
http://img381.imageshack.us/my.php?i...rown1488nr.jpg
So does this mean I am being limited by my PWM? My cpu hasnt broken 40c yet....I wanna keep pushing it...I think I am going to need 1.6somthing to get to 3.1ghz spi stable.
Well, my ram is pissing me off still but here it is....3ghz pi stable. :banana:
My PWM was pushing 60C the whole time...my CPU never broke 40c.
i never saw mention about a fan on the top corner of the board. i have a 120mm up there to keep all the important mosfets and ram cool.. pwm is idling at 28c for me
What stepping do you guys think the new 146's on ewiz has? Anyone get theirs yet? I noticed the ewiz 148's are CABYE.. so maybe 146 are too..
Sorry I'll just be so pissed If I get a CABGE, it will be a big downgrade from X2 at 2.67ghz
I am running my SD 3700 verry stable at 2900 using BIOS 310.
Will the 146 Opty run the same or should I upgrade?
What are you guys using ?
Ordered mine from ewiz last wed and I got a 148 CABNE 0528 GPMW
Well My first 30k run in 2001 :toast: :toast:
http://service.futuremark.com/compare?2k1=8759049
It was with default x850xt and My First 3 gig run :) man its fast and faster than my x2 4400 everwas..
Was running the Ballistix 11x273 with 1.5v on cpu.. Guess I could try less volts but wanted to make sure it would make it lol..
Thank you AMD for a great chip as I got a vience, x2 4400 and nothing come close to this..
How did you get a Cabne? everybody else is getting Cabye from Ewiz, including me. Ordered mine last Monday.....Quote:
Originally Posted by airwolves
man... kinda stinks about these cpu's running warmer.
seems strange though that temps are all over the place for people... but then again i guess some people's water cooling is better than others...
i was hoping for 2.9 to 3.0 with 1.5 to 1.6 volts but seems like temps get too high for me.
and i agree NYCTeeN82... strange he got a CABNE while most others including me got a CABYE 0528GPMW.
well i ordered a 146 from ewiz which should be here Friday. i'll be sure to update and let you guys know how that one does.
This thread convinced me to jump on the bandwagon too :D Yesterday received a 148 CABYE 0528GPMW ordered from ewiz on friday. Pretty happy with my current 3500, but thought I'd give one of these a try. No time for testing now, hope to post some results this weekend.
Congrats on that awesome chip bro, just be very careful if and when you remove the IHS....$300 isn't exactly cheap, I still haven't decide what to do with mine when I receive them, the TT Big Typhoon will be here tomorrow as well so I"m not sure if I should stuck the massive heatsink on it to test it on air first, or put it straight under the PCICE phase change :D :DQuote:
Originally Posted by Nettwerk
Yes all the people that just recently got Opteron 148's from Ewiz are getting the CABYE 0528GPMW (and myself). Everyone who has this one, post your results. Your max stable results. Not 1M SUperPi, but Prime 12+ hours.
Mines 2805 is stable @ 1.4V. I can't seem to be able to do anything above this. 2850 @ 1.5V or 1.55V errors out in Prime. I hope 2805 isn't the wall. Temps are under 50C on Full load.
that's a weird one... what prime you running small/large ffts or blend ? try prime95 v24.14Quote:
Originally Posted by NYCTeeN82
Prime Custom FFT´s In place every 15Minutes changing. Thats maximum Stress for the CPU!! Prime Blend only tests the Ram!!!! And Large is testing the Ram and the CPU!!
Best for the CPU and the hardest Test is Prime95 Version 24.11 and higher.
Ultimate CPU Test.
I would like to hear from others who have the 146 CABGE. How high they can OC.
If someone were to order one today from ewiz what do you think the best chances of getting a good stepping are and what flavors 144,146,148?
And OEM or Retail? Anyone gotten a CABNE OEM?
yay just got my opteron installed ...
Its CABYE :( but it was the best I could get !
Lets hope for some Mhz pwnage! I want it to clock better as my 3500+ that stopped at 2.6Ghz 1.75V :stick: ..
For now the opteron is like 15 C lower in temp idle then my NC wow :confused:
Where did you buy yours flapdrol? alternate.nl ?Quote:
Originally Posted by F|apDro|`
yep :) ordered it tuesday
still have to format my bench HD so I can tweak a little :slap:
testing 32M at 3007mhz and weirdess experience so far with 2x 512MB Gskill PC4400LE on 180 divider 32M would clonk out 2-3 loops in at 334HTT/300mhz 2.5-4-3-6 at 2.85-2.95v
so decided to try 2x 512MB Patriot PC3200XBL TCCD at 180 divider 32M and would clock out 1-2 loops at 334HTT/300 2.5-4-3-6 at 2.69v
so thought why not try 166 divider with mem at 273mhz 2.5-3-3-6 7-17-2223 with Patriot PC3200XBL
32M
at 2.69v = clonks out 2 loops in
at 2.76v = clonks out 4 loops in
at 2.79v = clonks out 5 loops in
at 2.85v = clonks out 6 loops in
so change from 7-17-2223 to 8-18-2223 loosening Trc and Trfc
at 2.85v = passed in 24m 29s!
http://www.fileshosts.com/DFI/NF4_SL...rpi-32m_tn.jpg
Prior to this revelation, i was upping vcore with no effect and it turns out it was vdimm that was lacking! So now i need to lower vcore and see what happens :)
Strange is at 300-312mhz 2.5-4-3-6 only 2.69v is optimal for this Patriot, but at 2.5-3-3-6 it handles volts fine!
Perc can confirm this weird experience regarding vdimm as he uses same ram!
edit: Can confirm so far, lowered vcore by 0.025v in bios and tad da!
http://www.fileshosts.com/DFI/NF4_SL...68vcore_tn.jpg
further proof
http://www.fileshosts.com/DFI/NF4_SL...pi-32m_tn2.jpg
Quote:
Originally Posted by ozzimark
Ok I have a theory I am going to throw at you guys, let me know if it sticks. I am wondering if my not being able to get my PC4000 ram above 215 has something to do with them overheating. I know they are in the same area as the PWM and my PWM is reading 60+c at load. Do you think there is a problem there?
there's one way to find out. increase airflow to the point where you're not overheating and try to see if you can go further ;)
sounds like some of your mosfet sinks have bad contact or something :(
I have a another fan on placed on top of my heatsink facing the ram now. Seems to be cooling the PWM about 5c better. I have a feeling it is just the mosfet sinks though. I would reseat those but I heard they are soldered on.
my out of the box result :o
not tweaked or stable :o
Quote:
Originally Posted by F|apDro|`
Really pushing that vcore huh. I don't think you will need it that high to get to 3003mhz.
My RAM cooling idea was a no go. The fan over my ram is keepingmy PWM cool though, not sure how important that is. What do you guys think the max temp for PWM is?
not bad, I'm running at 2.95 at 1.55v with my CABYE 148 -- temps are still very high though.
Guys , let´s start to post the maxTcase value? already post mine on the tcase thread , but I think will be a good idea to post here (to many diferent cores/steppings on the another...)
I didn´t test my processor yet , all I did was set it to 2700mhz at default vcore and it appears to be very stable (primed by 1 hour and 4 hours rendering a work scene in 3dsmax6)
Please report the complete info (bath, year/week...)
OPTERON 148 CABYE 0528 GPMW
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 148 (San Diego)
CPU Speed: 2695.40 (245.04 x 11.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 65C
neh dont think so ...Quote:
Originally Posted by foofreaknfighte
My mobo sux cus onboard LAN died cus of OC and since then it does some weird things ...
But as I said this is out of the box :)...
I Primed 260x11 @ 1.6V for 2 hours ... then it gave error ... Max Load temp = 47C ...
Now Priming again and letting it burn in and AS5 settle :). I know vCore = high but I need prime stable ;_;
edit:
my MaxTcase = 57C :(
I like that 65C more pera
Stepping:
http://www.xtremesystems.org/forums/...chmentid=38825
WOW. i am so happy someone is experiencing this same crazy :banana::banana::banana::banana:!Quote:
Originally Posted by eva2000
quickly, lemme post my confused situation, and lookin ato both your comments and revelation and my situation it seems like the same issue!
ok. so basically ozzimark was saying something else must be holding me back. all mosfets are sinked, systool and everest shows me that system temps are decent. chipset at like 20°, system temp at like 40° + actually touching the mosfet sinks and that whole area around the socket is pretty cool and has airflow.Quote:
Originally Posted by elrolio
but yea, looks like eva had the same experience as me lasst night, only i wasnt able to figure that whole mem thing out since im limited to 2.6 essentially cuz i have no active cooling. hmmmz. any ideas?
oh and i had a buncha screenshots showin the weirdness of what was happening. will post em when i got home as i was still testin all the way till when i left for work.
So what's the current XS status on benching those dual core opterons?
Quote:
Originally Posted by F|apDro|`
I know what you mean. I am priming right now, hoping to be able to prime for 8 hours at 2.8ghz. I think I should be able to do that, and I guess that I could be happy with that...might pick up a CABNE if I see one though.
well tried 3Ghz @ 1.6V via clockgen ...Quote:
Originally Posted by foofreaknfighte
it was picstable just as at 1.65V :stick:
Here's a 150 quick results. I'll probably play with it some more later. At the moment there seem to be some issues with BH-5, the board or mem controller. Maybe bios and or setting? S&M MEM TEST seem to error 3/4 way through at speeds that would complete before ( when San Diego used) tested at 310x11 166 divider as well. Otherwise it's stable. Plays games etc. So will have to screw around with it later and see what's up. Doesn't seem to have any obvious startup probs with subzero. Can't say for Cascade type temps at the moment though...
I'm on a diff comp now so only have this jpg to show.:D
It also boots at 330+ with 10x multi etc.
http://lord.e-access.com.au/Opt150_Spi1mm_12x284.jpg
Quote:
Originally Posted by F|apDro|`
Try a non-clockgen when you get a chance. I had a lot more trouble keeping pi stable that way...
CPUID: 20F71
APICID: 0
Revision: SH8-E4
Precessor: AMD Opteron 148 (San Diego)
Speed: 2805.00 (255 x 11)
Platform: Socket 939
MaxTCase: 65C
VCore: 1.400V
CPUID: 20F71
APICID: 0
Revision: SH8-E4
Precessor: AMD Opteron 146 (San Diego)
Speed: 2650 (265 x 10)
Platform: Socket 939
MaxTCase: 55C
VCore: 1.400V
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 148 (San Diego)
CPU Speed: 2860.20 (260.02 x 11.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 57C
very nice!Quote:
Originally Posted by NYCTeeN82
here's my 146:
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 146 (San Diego)
CPU Speed: 2900.08 (290.01 x 10.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 63C
oops, seems that i'm at 2.9ghz :confused: :D
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 148 (San Diego)
CPU Speed: 2210.19 (200.93 x 11.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 65C
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 148 (San Diego)
CPU Speed: 3300.84 (300.08 x 11.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 65C
Quote:
Originally Posted by el rolio
Prime, or super pi...similar mathematical error...all stems from the same thing => instability. Ok buddy?
Superpi more tests the Ram than the CPU!
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 146 (San Diego)
CPU Speed: 2800.00 (280.00 x 10.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 67C
Just got my 148 in today from ewiz. CABNE :woot:
First attempt. Have to run 2T because of running 4x512.
Time to update my sig......This one's a keeper. :fact: :toast:
Well, why pi at 3ghz was fairly easy...getting more than an hour at prime is proving to be extremely difficult. Don't want to bring up the whole pi/prime debate but I am kinda uncomfortable having my computer write files when its math is .1 off.
OPTERON 148 CABYE 0536 GPMW
Running 1.5v @ 2.85GHz on quiet air Prime Stable 12+ hours; anything over 260FSB fails prime even at 1.65v and with Mem on a divider, maybe my neo2 plat ?
CPU Information (CPU #1):
Standard CPUID: Family: F, Model: 7, Stepping: 1
Extended CPUID: Family: F, Model: 27, Stepping: 1
CPUID String: 20F71
Processor APIC: 0
Processor: AMD Opteron 148 (San Diego)
CPU Speed: 2849.16 (259.01 x 11.0)
Revision: SH8-E4
Platform: Socket 939
Startup VCore: 1.400v
Maximum Case Temperature = 59C
u guys should post these maxtcase values in the thread dedicated for this
Quote:
Originally Posted by foofreaknfighte
Lighten up bro. :rolleyes: I posted a quick screenie like 5 minutes after I popped it in my board. Just wanted to share some quick info. :)
I really, really agree. :( Suddenly this thread has turned into a "what's your MaxTcase" instead of an oc thread. I really don't think a higher mtc means higher oc but if that makes your wheel turn, fine. :) Even if it does, you can't find out what it is until you buy the cpu and test it. It's not like a stepping you can hunt for. Or, even a T or N on the cpu that may or may not have anything to do with oc'ing the cpu.Quote:
Originally Posted by dinos22
Please try to stay on topic :off: and let's see some more tweaker ss in with the rest of your oc. Also, lets not :horse: over "you didn't prime enough". I thought this was XS.
Then by all means you need to have your computer prime stable. I am fine at 32m or OCCT stable. I am not trying to make you uncomfortable by saying you should just be doing 32m or OCCT, please don't make me uncomfortable by saying I should do prime.Quote:
Originally Posted by foofreaknfighte
more importantly post the cpu's idle/load temp and ambient room/case temps you have to achieve the clocks :)Quote:
Originally Posted by dinos22
no way, the another thread its for a64... :DQuote:
Originally Posted by dinos22
heheheh let's invade the A64 thread hehehQuote:
Originally Posted by periquitos
it's easy......as eva2000 said above..............do the OCs....idle load and you can include a screenie of maxtcase as well in there.....that way it's probably more informative anyways
has anybody ordered from monarch? they have OEM 146's in stock, i want to jump on it, but a cabge would be a side-grade for me.
I think that they posted that they were instock to just hype things up a little and get orders in could be for real though but dont give your hopes up
ok fellows, this is where im at. sorry i dont have photoshop installed. i will try and come back to it. maybe i can up the voltage a bit, tho it was superpi that threw the error, leading me to believe it was the memory givng me issues
and here is the cpuz validation http://valid.x86-secret.com/show_oc?id=44676
http://img478.imageshack.us/img478/1...reen2zt.th.jpg
the ambient temp as read by speedfan on the 6800 is 29 degrees.
basically i hit that wall at 280 last night, wass given a hot tip that maybe my ram can do a certain speed, my cpu can do a certain speed but the memcontroller cant allow both. so now im runnin ram closer to stock... but it seems there is tweaking to be done as i can do 1m, 2m, 4m, 8m, but not 16 yet stable in super pi.
oh and the concept is, if this is how its gonna be, i might as well put the bh-5 golds back in.
all in all tho, side effect and ozzimark really helped out, thanks guys.
aiit folks, got the 32m prime stable. upped ram voltage to 2.75v and also tried a diff combi of VID and % to get where im at of about 1.55 avg.... gosh i hate neo2 fluctuating vcore.
http://img478.imageshack.us/img478/7...reen5pv.th.jpg
as it stands now im done for tonight. gonna start a prime blend test? i guues thats the best to do and let it run till morn. should be a good 7 hours and hopefully it runs thru the night. *wish me luck!
im pretty sure im pumpin a tad bit more volts than is actually necessary to be stable but its just in an effort to compensate for the wildy fluctuating voltage courtesy of the neo2. *sigh.
What bios are you guys using for the 2GB Ballistix? can you please post the Tref value, Dram drive and data strength?
Then start your own thread just for MaxTcase. There is no sense of trashing up an oc thread with that. Someone who just gets an opty or is new to the forum and wants to find out about how the opty's oc shouldn't have to go thru a lot of MT posts to find oc info. This tread has pasted up the venice, sd and x2 threads is a short time. Please don't trash it up.Quote:
Originally Posted by periquitos
periquitos, your new here, please respect other people threads. If MT is that important to you, start your own thread. Don't hijack. :nono:
I have got the same stepping here:Quote:
Originally Posted by Whap
148 0536GPMW 0189er Batch
(not so nice as my 144, but really 3GHz)
http://mitglied.lycos.de/freestylerc...2V%20prime.JPG
free