then...you might need to try a different brand of memory.
i would say 449 fsb is doing very good...
Printable View
then...you might need to try a different brand of memory.
i would say 449 fsb is doing very good...
Well, for me at every divider the memory maxes out at same freq while in other board it'll go way faster, that's why I'm limited at 1:1, your board seems really weird...Quote:
Originally Posted by BAR*B*Q
hehe. it were two different brands. g.skill and cellshock.
i tried mushkins aeneons too. but they couldnt stick with the microns.
im never satisfied anyways in the first place :D
but the fact that the gap between 100 % stable and not even bootable lies between one single clock makes me crazy. another thing is that i can reach the 449 mhz with the lowest voltage settings.
thats why im really in a huff :)
:fact:
Quote:
Originally Posted by DaWaN
Maybe another thing then, did you used clockgen or bios ??
both. i think i got a freeze with glockgen above 450 mhz.
may be your cpu ?
nah, it ran on p5w with 465 mhz when i remember correctly.
but ill have another look on my oc pics to be sure. its only on my disk at home.
€ : nope, cpu ran with 465 mhz 1:1 on p5wdh.
now...
i just (cold)bootet with 454 mhz on the biostar (set in the afternoon but also weird because usually it sets cpu clock on default after a crash)
anyways, i got a freeze a few seconds. surprise, surprise. but wth is the board trying to tell me :confused:
anybody knows where the sensor reads out sys temp ? actually temps are fine.
even one of my early ideas was that a cold bug is the reason :D so i turned on the heater but that didnt work either :rolleyes:
I did 36gp with this motherboard and it perform very well. This Motherboard can do easy 540*6 cpu
this 6600 in aircooling, i m going to try it under phase change. :D
Biostar Tforce 965p DLX
2*1go Gskill pc6400 1:1 4-4-3-8
http://users.skynet.be/pt1t/6600/36GP_13_891.PNG
are theese g.skills micron or elpida ? any special cooling on your board ?
Quote:
Originally Posted by BAR*B*Q
aLL @ stock, Gskill are D9 , ~600 in 4-4-4 2.6v
if you use higher Vcore and Vdimm, i bet you would get higher FSB.Quote:
Originally Posted by BAR*B*Q
Anyone in the U.K have one of these?
Not seen them anywhere
how you got 2.6v?? vdimm mod? use ddr2 optimizer??Quote:
Originally Posted by Pt1t
hmm, 2,6 dimm and 1,6 core voltage read out in bios should be enough mate.Quote:
Originally Posted by Ace-a-Rue
for 445 i used ~2,1/1,37.
Quote:
Originally Posted by BAR*B*Q
????
http://www.lejabeach.com/Biostar/965...5ptbios-22.jpg
i used stilt mod (post #29)
i think the only thing left i could do, is try another cooler with a decent mounting.
even though Pt1t is reaching more then 500 stock :rolleyes:
OK, I see you have the Vdimm mod. Thanks :)
So does this non-deluxe model allow you to change CPU multi?? :confused:
Quote:
Originally Posted by Benny Lodewijk
First bench under Single Phase,
6600 L631a674
Biostar Tforce 965p deluxe
2*1go gskill 6400 HZ 1:1 4-4-3 2.2v
Just a quick Boot/1M during my lunch time , more result under this phase change later.
http://users.skynet.be/pt1t/6600/500X9_dod.PNG
where u guys r getting this board? cant find it
i don't think so as reported by another user.Quote:
Originally Posted by uclajd
ok thx..:toast:Quote:
Originally Posted by JWilson
i thought its maxed at 2,4v just as the Biostar AM2 boards
Max fsb with passive chipset cooling ...
No multi in bios doesnt help me :D
http://users.skynet.be/pt1t/biostar/...dlx_fsb500.PNG
Quote:
Originally Posted by wedfighter
Hmmm.... Let me check into that. I just don't remember. I have all the voltsge readings at home....