systemviper is selling x3380. Even mfII would be enough for 9.5X.
Printable View
systemviper is selling x3380. Even mfII would be enough for 9.5X.
:p:it`s easy to reach 500x9 clock with MIIF :) I just need a good chip :up:Quote:
Originally Posted by zsamz_
Easy with a duel. I think it will be difficult to hit that with a quad, but it is possible.Quote:
Originally Posted by WaterFlex
500 FSB stable on the m2f is very unlikely tbh. 470 FSB large FFT and blend stable is all I could do. My chip is a good one too but the board wouldnt do any better. In fact my X48 REX did better.
oh no dont revive the MFII again waterflex :rofl: nightmare for quadsQuote:
Originally Posted by WaterFlex
:up: Agreed It's Too Bad For Quad Not Stable Over 500Mhz FSB:shakes:Quote:
Originally Posted by andressergio
But UD3:shocked: Awesome Board :yepp:
Yeah i am trying to find a UD3P to replace my maximus formula x38 that is down right now. I would like to see what i can do with my q9650 now that i know there was a board made for them.
yet another update :) ..... 470*9 now at 4.230Ghz - Gflops gone up too - temps ok and 20 linx stable, 8 hours p95 stable too
i recon this chip will easily do 490*9 but i'm not so sure for 24/7 usage - its 4.23Ghz @ 1.325v 24/7 - i might go to 480mhz with 1.35v - i'll see!!
Nice work, my P5Q-D topped out at 473 FSB, but it isn't a great example and had an A2 rev NB. Does your board have an A2 or A3 rev NB? (check CPUZ in mainboard tab). Is it prime 95 large FFT stable?
i've got the A2 nb!!!! gonna get 4.4Ghz out of this beast - i've had it at 480mhz this week and trying to stablize it - but 470 is good 4 my 24/7 - until 480 is stable!!!!!!:)
its 20 linx loops stable and i only do 6-8 hours P95 as its a waste to stress HW for that long as its never going to happen in games etc..
sorry cryptik - to answer your original q - i think i use large fft yes - i'm not using blend as my ram is running 1:1
Guys! I`ve just bought Q9650!
Batch is L842B847.
enjoy it mate and buy a giga board :DQuote:
Originally Posted by WaterFlex
Nice one, hopefully you'll like it :up:
Congrats she is a lil beastie :) lot of fun to play with :up:Quote:
Guys! I`ve just bought Q9650!
Batch is L842B847.
I will get to home on Sunday :) Some numbers soon :up:
well I have been waiting for my cpu pot to get here so I can put my i5 650 and the memory under cold for the Gigabyte H55N challenge, so instead of waiting around I hooked up my 775 rig which is new to me.
Nkresho's old chip (C batch, 1.15 VID), UD3R and GSkill PI 9600's
http://i35.tinypic.com/2uy56b7.png
I can not run linx as it gets too hot even under my loop (EK Supreme HF>Swiftech Micro Res>XSPC RX360 rad w/ 6 SanAce fans in push pull>MCP655) and just restarts however prime blend is looking great:up:
That is an awesome cpu. Nice work.
Thats a great chip, you will enjoy it. I still have my C chip from that same batch, they do run hot.Quote:
Originally Posted by l0ud_sil3nc3
Very nice Q9650 :up:Quote:
Originally Posted by l0ud_sil3nc3
all this batch L847C are very good clockers if you could beat the temps :S, still to find time to get a good breath to build my watercooling, but my temps 3.2/1volt linx->~60... push-pull ultra 120x@ 1000rpm, dictate a watercooling setup as fast as possible...
then you will need to sell me the chip,i will run LinX for you no problems cooling here:DJ/KQuote:
Originally Posted by l0ud_sil3nc3
anyways super awesome OC!!! you got yourself an awesome cpu:up:
thanks radaja and I will keep that in mind as I have another Q9650 to test also a C batch that will be incoming shortly. I might send you the low VID and see if you can get it in the linx 4.5 stable club because I am not having good luck.Quote:
Originally Posted by radaja
Yeah I have an L847C too, it's very hot :D
what is the VID?Quote:
Originally Posted by CryptiK