Printable View
Well, I have 2 sticks of the OLD ballistix 4000 that are single sticks, no problems. I can prime all damn day, whatever... Are u guys sure that the ram is really erroring because it's bad? Maybe u just need active cooling on it, they do run hot like tccd does.
As I mentioned, I have always been running active cooling on it. The ambient room temp was always between 68F (20 C) and 74F (23.3). Right now it's 69F (20.5C). That's pretty damn cold ambient temp compared to most.Quote:
Originally Posted by fareastgq
I have the system mounted in a CM Stacker case with a crossflow fan, and 2 80mm Vantec Stealth Fans @12V about 1.5 inches away. That's 54 CFM from the Stealth fans running over them. The memory is cool to the touch. It still errors out like crazy. The one stick refuses to post even at 200Mhz 3-3-3-8/3-4-4-8/3-4-4-10 2.6v/2.7v/2.8v.
My XMS-3500 seem to run fine.
Sorry, I missed the active cooling part, I guess the old single sticks are better than the new sets. I'm glad I have a good set. Time for u to rma looks like.
Here's my effort:
johnbarry | 2x1GB G.Skill F1-3200PHU2-2GBZX | 3-3-2-5 1T @ 262MHz | 2.82V | Link! - SPi 32M Stable: Yes
Most of those timings are at auto which is pretty loose already, but a couple more MHz might come out with even looser timings. Voltage is pretty much maxxed out with little or no difference between 2.8 and 2.9. 3.0V has no gains over 2.9V from what I've seen.
I've got active air cooling over the ram too.
I can pass Super Pi32M no problems, but If I am to get the max overclock, I have trouble passing Prime 95!
My question is, is SuperPi good enough?
I was one of the first with the ballistix. I had 2 single 1gb ballistix tracers from new egg.
i just recently sold then (monday) to get the muskin redline 2gb kit. At time of sale they were running at 255 3-3-3-8 2.6v No errors in memtest. Just the way i left it 2 months ago when i hit my sweet spot. Again these were Ballistix Tracers (pretty flashing lights).
No errors or issues here after 2 months.
AMD 3000+
DFI LanPARTY EXPERT
GSkill 2GB HZ
MSI 7800GT SLI
DDR570 3 4-4-8 1T 2.49V
http://img4.picsplace.to/img4/13/570.png
Hello guys...
I really need to know something and hope SOMEONE can enlighten me :D
Ive got the CRUCIAL BALLISTIX 2GB KIT (DDR500). From looking into this Ram, there was a fiasco as to some of this ram having different chips on them. I just wanted to make sure that my kit was as it should be, so from reading the posts here, was advised to take off the heatspreaders to check the chips themselves.
Just wanted to know if this VOIDS THE WARRANTY? It was a bit of a pain getting the heatspreader off one of the Dimms and scratched the heatspreader a tiny bit ie just left a mark on it. But nothing else. I did my check then put it back together again!
At the moment Im running the RAM at 290Mhz (2.64V)1-1 (1T) with an AMD Opteron 146 at 2.9Ghz, primestable and at 48-49 degrees at full load (1.48V). It passes Memtest no problems
Just worried about the warranty terms if something was to go wrong in the future. Any advice is appreciated.
Thanks.
No need to answer... :D
I posted the question in a new thread in greater detail.. :)
i have had the same problems as you, Brit. ordered mine 8/23/05. slowly seemed to be dying on me... gkskill gh works totally fine though. im calling crucial next week
What do you know about these?
http://www.newegg.com/Product/Produc...82E16820141236
PQI 2-3-2-5
*bump*Quote:
Originally Posted by Aleman
Anyone?
Could they have UCCC? or Micron -5B D???
hey guys, i am going to be buying a 2x1 gig kit asap. The problem is that i need memory that will do 270 to get the max out of my 3800x2. In looking at the results it appears that the ballistix is the way to go. what would be the safest purchase for ddr540? thanks again. it will be with the sysem in my sig
cronic go for the ballistix, they do 270 for sure.
Most likely Infineon chips. Be-5 or CE-6 if your luckyQuote:
Originally Posted by Aleman
Well ive seen that they go up to 250MHz in the 2GB DATABASE, so any OC will be accepted, superB price, 210dlls!!!
Hello all,
I hope that someone can help me here! I have the 2GB Ballistix memory installed in my system and my AMD 146 Overclocked at 2900Mhz at the moment. However, the weird thing is, when the RAM is overclocked to 290Mhz it passes Memtest86+ but the Blend setting in Prime 95 fails after about 10 minutes. When I use a 180 Divider, Prime 95 is oki.
Any ideas here? I really want to get my Ram upto 290Mhz and run 1 | 1
But being a newbie, im not sure about the settings
:(
@Rixx
Im pretty sure the memory controller of your CPU is having it hard time!. Try setting loose timmings or 2T just 2 check if that helps!.
Somebody experience with Hynix D43 chips? My friend has bought the most cheapest 1GB sticks and it came with Hynix D43 chips on brainpower PCB :toast:
High latency chips(3-4-4-X), dont like too much voltage, usually hits 245 - 265Mhz @ 2,8Volt, at high voltage (3.1v+) is cooling recommendedQuote:
Originally Posted by DaWaN
Yes but those sticks are 1GB, never seen a Hynix D43 1GB stick, but the SPD is 3-3-2 so it's indeed not very low latency. And the chips were pretty new 0536Quote:
Originally Posted by Aleman
Hi thanks for the reply!Quote:
Originally Posted by Aleman
Being a newbie, could you please tell me what I would have to do to loosen the timings? i.e. I am running 3-3-3-8 at 290MHz, what would you recommend?
Also, running 2T will surely be much slower than 1T? With your advice, would it theoretically be better to:
1> CPU 2.9Ghz Memory 263Mhz (180 divider)
OR
2>CPU 2.9Ghz Memory 290Mhz (1 | 1) but loose timings
OR
3>CPU 2.9Ghz Memory 290Mhz (1 | 1) but loose timings AND 2T
What would theoretically give me the best performance in order?
lol. I hope I am not being too demanding and that you can understand me. Thanks.
Rixx
Ofcourse tight timmings is the best, but the way to overclock is to Reach X's Speed using ANY METHODS that are possible but to read that speed totally stable. Once you have reached your speedgoal, you can tweak that using better timmings.
I'd use 3-4-4-8 and move tRC to 9~11 and tRFC 16~22 and check on that. Tighter is always faster but less stable. 2T is ok if the Memory Controller is a biatch.
Just got these back from rma.. They will do the settings in my sig 8+ hours prime stable..
http://img333.imageshack.us/img333/5559/untitled1ck.jpg
http://valid.x86-secret.com/show_oc?id=53286
THunDA, mind if I ask what the batch number is on the stick they shipped back out to you?
C1115T.88Quote:
Originally Posted by BRiT
56278
Is that what you wanted to know ?
EDIT..
Here is my database entry at dfi-street with the settings in my sig..
http://www.dfi-street.com/forum/show...8&postcount=87
EDIT #2..
Last night I lowered the multi and started upping the htt to find the max of the ram .. I managed to pass 8+hours of prime at 290x9 with the same settings and voltages in my sig..
http://img54.imageshack.us/img54/87/untitled7iz.th.jpg
290 seems like the max prime stable speed.. I did get 295 to prime for an hour but thats it..
As many others experience, my first pair of Ballistix could do 300MHz prime and SuperPI stable at 2.9V. Sudenly after 2 months they started to show errors. RMAed to Newegg and got a new pair. Well now this new kit is having hard time to pass 285MHz :slapass:
WTF very expensive memory now just performing poor range. Not sure if I should RMA them again...
May get an even worse pair
I need me some ballistix!
LOL complaining about pc 4000 memory doing 285Quote:
Originally Posted by RafaDel
that others got 300 doesnt mean that every pair goes 300.
It just means that they were very lucky
Remember, pc 4000 is supposed to do 250...
I have noticed that there is a stability issue using memory dividers if you have a pair of ballistix with a large max FSB differenece, ie. one doing 260 and another doing 285+.
For instance I had a pair that one did 285 stable and another doing <260, in that setting 200 and 183 was usable but no other (except 100). I would get reboot cycles when entering windows if I even got that far.
I managed to get a more evenly matched set where each did 275 and no more problems.
Just speculation however, it might just have been one of the sticks being bad with memory dividers.
/Q
:)
Mushkin extreme Perfomance XP4000 (Samsung UCCC)
testing on
Abit AN8 Ultra
150 Opteron
268-3-4-3-8-1T/2.5V
http://free.pages.at/speedy444/Hardw...B.@.268mhz.png
285-3-4-4-8-1T/2.5V
http://free.pages.at/speedy444//Hard...B.@.285mhz.png
Really well selects
mucker | 2x1GB G.Skill F1-3200PHU2-2GBZX - ??? | 3-3-2-5 1T @ 259 MHz | 2.75v | Link! - SPi 32M Stable: Yes
Pi32m
http://members.cox.net/mucker/GSkill/GSkill5Opt.jpg
OCCT
http://members.cox.net/mucker/GSkill/OPT146.jpg
Just a quick note to all of you since I was among the first adopters of the Ballistix 2x1GB kits.
Apparently one stick flaked out randomly on me about a month ago, very strange random blue screens and finally after extensive testing found one stick to be bad slightly.
Even at defaults speeds etc it would sometimes show memtest errors, it was tough to troubleshoot because I put each stick on another PC (Intel based) and ran memtest 8 hrs no errors.
Crucial was quick to respond and RMA both sticks as the KIT, since then not one BSOD or failures. Hopefully this helps someone in the future that might have the same type of issue.
Samsung UCCC / Brainpower PCBs (mine showed up blue spreaders on green PCBs instead of black on black)
2.5v + .3v enabled
orange slots
704-2BTa bios
270mhz @ 3,4,3,8 1T
CPU-Z validation
memtest v1.65 30 passes
http://img521.imageshack.us/img521/3...t30x5pd.th.jpg
SuperPi 32M
http://img521.imageshack.us/img521/5...032m7ue.th.jpg
3D stable
http://img521.imageshack.us/img521/8...70mz4ff.th.jpg
275mhz 3,4,4,8 1T
SuperPi 32M
http://img202.imageshack.us/img202/9...m2755hs.th.jpg
http://valid.x86-secret.com/show_oc?id=54834
3D stable
http://img202.imageshack.us/img202/2...able2hc.th.jpg
http://valid.x86-secret.com/show_oc?id=54836
Test Rig specs:
A64 3000+ Venice E3
DFI NF4 Ultra Infinity
2x 1GB Corsair Value Select C3
Leadtek 7800GTX 256MB
TT Silent K8 HSF
Enermax 535w All in one
Windows XP Home.
VDIMM = 2.60 volts
Vcore = 1.40 Volts
CPUz Validation http://valid.x86-secret.com/show_oc.php?id=54859
http://home.swiftdsl.com.au/~apollo1...001%20copy.jpg
http://home.swiftdsl.com.au/~apollo1...001%20copy.jpg
http://home.swiftdsl.com.au/~apollo1...t255MHz_01.jpg
http://home.swiftdsl.com.au/~apollo1...001%20copy.jpg
2x1GB Mushkin High Performance Model 991434.
Screenie: http://photo.insanelabs.com/mushkin2x1gb.jpg
Validation link: http://valid.x86-secret.com/show_oc?id=55107
I've got them yesterday from Newegg and haven't played around too much yet. I'm sure after more buring they will do better. I already like them a lot since they auto detect 2-3-2-5-1T on my DFI Ultra-D. After I RMA'd a pair of crappy OCZ OCZ4002048ELDCPE-K that didn't go past 208 at 3.0v and auto detected 2.5-3-2-5-1T I'm going to stick with these.
2x1GB GSKILL HX on MSI K8N Sli 250mhz 2.5-3-2-5 2.50V
http://img412.imageshack.us/img412/3...ench0zn.th.jpg
http://valid.x86-secret.com/show_oc?id=51944
Nice :toast:Quote:
Originally Posted by Rubex74
What Vdimm ??
Had my z503 ballistix less than a month at ddr520 and they flaked out on me. I am hoping the rma from newegg will be different batch.
Tx, Vdimm is 2.50V.Quote:
Originally Posted by alpha0ne
BB
Nice results! I have the same kit, but I have it running in an Nforce2 motherboard ATM :(Quote:
Originally Posted by Staucher
The VDIMM is pretty low, does it seem like it does better with lower voltage?
I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors.Quote:
Originally Posted by HelloIDistance
I can't speak for Stauncher obviously, by my experience so far with the same sticks has been that 2.5v-2.65v is optimal and that anything more just increases instability and errors. I noticed an increase in errors below 2.5v as well. Mine are best right at 2.60v.Quote:
Originally Posted by HelloIDistance
Exactly the same run at best with 2.5-2.6V the more brings only nothing.Quote:
Originally Posted by hawkeyefan
Very Good Mushkin :clap:
2.6 is about max for me as wellQuote:
Originally Posted by hawkeyefan
Mushkin UCCC is very very easy to work with :)
JNav89GT- Stop being a mushkin whore. All your posts seem to be about praising or defending mushkin. :rolleyes:Quote:
Originally Posted by JNav89GT
He cant, hes on the payroll :DQuote:
Originally Posted by Squire
or beta team at least.
show some more respect.
my results sent
here are my results with this memory ddr550 @ 2.7v 2750Mhz
F1-4000USU2-2GBHZ
http://tinypic.com/imibg1.jpg
http://tinypic.com/imibly.jpg
2x1024Mb Corsair XMS C2
http://www.klokking.com/bilder/28232M.JPG
Validaition : http://valid.x86-secret.com/show_oc?id=57058
Here's some 2x1GB Ballistix Z503 @ 285, frankly they are a hair more impressive at 280 and below. Down at those speeds trfc can stay at 14 and twr, twtr, and trtw will stay at 2-1-2 and max asynch 7 ns. I'm sure these would do more for me if I wanted to run more than 2.78V through them, but knock on wood, these have gone a month with those volts and I just don't want to give them more due to all the failures.
http://mysite.verizon.net/res6otqr/s...s/_smaller.jpg
http://img361.imageshack.us/img361/8...t2gb2wt.th.gif
Oh yeah baby 100% stable
Marios | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 251 MHz | 2.8v | Link! - SPi 32M Stable: Yes
http://users.forthnet.gr/ath/mloupos/276132.png
Finally had a chance to test out the replacement Ballistix. I set tCL, tRCD, tRAS, tRP, tRC, tRFC in bios and left the rest set at AUTO. I'm running Bios 623 on my DFI SLI-DR. I haven't finished modding my case, so I'm still running stock air cooling for now. I started the tests then left to grab some food, so not sure what the max-temps were. I'll try running 2 instances (1 per core) of SuperPI next. In the meantime, how does this look?
BRiT | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 295MHz | 2.7v | Link! - SPi 32M Stable: Yes
EDIT: Provided for image picture from a different host...
Alright, last run for the night... Bumped up the voltage in bios to 2.9V with +0.03v enabled, reads 2.94V in WinXP, just for this last benchmark run. Had to tweak some of the memory settings in windows to get SuperPI to finish. Any suggestions on how to get this to 305Mhz?
BRiT | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 304MHz | 2.93v | Link! - SPi 32M Stable: Yes
My first test of GSkill HX:
http://img331.imageshack.us/img331/6...541t7ci.th.jpg
Validation: http://valid.x86-secret.com/show_oc?id=58758
Seems like we have a new first place entry here... Not bad at all considering the system is still running on stock air-cooling. :cool:
Alright, first and only run for the afternoon... Bumped up the voltage in bios to 2.9V with +0.03v enabled, reads 2.94V in WinXP, just for this last benchmark run. All the memory options set in BIOS except for tREF which is set to auto and Read PreAmble set to Auto, but manually set within WinXP with A64 Tweaker.
BRiT | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 305MHz | 2.93v | Link! - SPi 32M Stable: Yes
Only had time to do a quick run at the higher fsb before the holiday. I wont have time to try pushing higher until after this weekend. I suspect I may still have some headroom left, considering this is the first I tweaked the tREF setting. This CPU's memory controller is amazing for an X2!
BRiT | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 307MHz | 3.05v | Link! - SPi 32M Stable: Yes
Nice work dude, i'll push my memory s'more ;) while trying to keep 3-3-3-6.Quote:
Originally Posted by BRiT
I have these ram PC4000
http://img527.imageshack.us/img527/6025/gold9ya.th.gif
They have chip Smasung UCCC.
The Mb on which I mount to them is one DFI-SLI DR.
That bios advised to me?
623-3
702-3
704-2BTA... oorr ???
Set 4:
278 - 3-3-2-7 - 1T - 2,6V @ DFI nf4 SLI-DR @ A64 3700 San Diego @ RockOn
Memrest - bild vom set 4:
http://img485.imageshack.us/img485/8...dern6xq.th.jpg
http://img485.imageshack.us/img485/1...ndra3dd.th.jpg
http://img485.imageshack.us/img485/8...od141be.th.jpg
http://img485.imageshack.us/img485/1...core4ub.th.jpg
Nice Brit. Have you tried higher volts?
Im looking to get 2x1GB set of ram and have read that the Crucial Balistic can hit 300Mhz.
Does it mate which of these i get as one set are black the other yellow.
http://www.crucial.com/uk/store/part...L2KIT12864Z503
http://www.crucial.com/uk/store/part...L2KIT12864L503
Heres my entry. Its not a scorcher but it does alright. Prime and super pi stable.
[IMG]http://img474.imageshack.us/img474/1...11valid6iz.png[/IMG]
http://valid.x86-secret.com/show_oc.php?id=60015
2*1gb G.Skill HZ - samsung uccc - work nice with Gigabyte nf4 sli
full stable (32m, 3d, s&m, prime, memtest) at 272 3-4-4-8 1T and 2.83v (most don't need over 2.60v to reach the limits, but -don't know why- extra vmem here helps a lot!), and maybe it is the cpu (winchester core, D0 stepping), or (and) the passively cooled chipset which gets really hot... that don't allow higher clocks with 1T - will check it out soon
spi 32mb : http://img246.imageshack.us/img246/1...tspi32m5mx.jpg
cpuz validation: http://valid.x86-secret.com/show_oc?id=61264
Some results from the new sticks ... you wont believe it, but the first two acutally died. :rolleyes:
One of these days im going to drop down to 10x multi and run the tests again. I suspect the CPU is stopping me @ 270*11 as its on silent air cooling.
Ballistix PC4000 @ 270 3-3-3-8 2.7vdimm
http://www.urettferdig.no/forman/ima...270-stable.JPG
Here's my 24\7 settings with 2x1gig of Ballsitix and my new x2 3800..
(copy and pasted from the dfi-street oc database..)
==========
Genie BIOS Settings:
FSB Bus Frequency - 289
LDT/FSB Frequency Ratio - 3
CPU/FSB Frequency Ratio - 9
PCI eXpress Frequency - 100Mhz
CPU VID StartUp Value - 1.50v
CPU VID Control - 1.5v
CPU VID Special Control - Auto
LDT Voltage Control - 1.2v
Chip Set Voltage Control - 1.6v
DRAM Voltage Control - 2.6v
DRAM Configuration Settings:
DRAM Frequency Set - 200 1:1
Command Per Clock (CPC) - Enable
CAS Latency Control (Tcl) - 3
RAS# to CAS# delay (Trcd) - 3 Bus Clocks
Min RAS# active time (Tras) - 8 Bus Clocks
Row precharge time (Trp) - 3 Bus Clocks
Row Cycle time (Trc) - 9 Bus Clocks
Row refresh cyc time (Trfc) - 16 Bus Clocks
Row to Row delay (Trrd) - 3 Bus Clocks
Write recovery time (Twr) - 3 Bus Clocks
Write to Read delay (Twtr) - 2 Bus Clocks
Read to Write delay (Trwt) - 3 Bus Clocks
Refresh Period (Tref) - Auto
Write CAS Latency (Twcl) - Auto
DRAM Bank Interleave - Enabled
DQS Skew Control - Auto
DQS Skew Value - 0
DRAM Drive Strength - Auto
DRAM Data Drive Strength - Auto
Max Async Latency - Auto
DRAM Response Time - Normal
Read Preamble Time - Auto
IdleCycle Limit - 16 Cycles
Dynamic Counter - Enable
R/W Queue Bypass - 16 x
Bypass Max - 07 x
32 Byte Granularity - Disable(4 Bursts)
==========
2x Prime95 + 3dMark2001SE + 2xCPU-Z + MBM :
http://img466.imageshack.us/img466/9...titled16tx.jpg
3dMark2003 :
http://img466.imageshack.us/img466/9...titled23kr.jpg
3dMark2005 :
http://img405.imageshack.us/img405/3...titled34ap.jpg
Everest + 2x Superpi32m :
http://img466.imageshack.us/img466/1346/untitled4ky.jpg
==========
Is the database on first page still beeing updated?
I don't know either but these G.Skill Extreme Series HZ PC4000 I have, have been running 273MHz for two weeks strait at 2.7v 3,4,4,8 1T 100% load f@h.Quote:
Originally Posted by MonkSP
http://img.photobucket.com/albums/v136/wayland7/273.jpg
Not to mention game stable on everything I've thrown at them.
I've actually had them higher in benches but don't have the screenshots handy. To my recollection they did 285! But proof is the pudding. I'll get some screenies for that :)
Last edited by EnJoY : 09-21-2005 at 09:56 AM. :eek:Quote:
Originally Posted by MonkSP
Yer so in otherwords this thread is not being updated :rolleyes: :mad:Quote:
Originally Posted by gundamit
It would be nice to get another list going that separates the memory out by type. In addition to the 32m stabilty check a 3D check perhaps, since there have been reports of 3D stabilty problems. Not sure which test would be a good one to determine stabilty in games however. :confused:
10 loops of 3dMark? or someone could make a benchmark (demo run-through) of the top5 or so games so to simulate gameplay...
or just *require* people to play games for 2hrs :woot:
Really pulling my hair out ATM because I just cant make up my mind re 2GB kit :mad:
Looking at either the G.Skill ZX or HZ or maybe the new OCZ Gold XTC PC-4000 EL ???:confused: :confused: :confused:
It seems the ZX are coming good after a few bad batches so who knows ??, I need something to keep up with the Opty 170 CCBWE 0546XPMW I bought yesterday that 'should' get to ~ 2.85 ~ 2.95GHz
Any ideas anyone, I'm useless when it comes to deciding on which ram to buy though I am still in awe of my G.Skill GH :D
Database Updated! :cool:
I added every valid entry that has been pmed to me since mid november. Don't see your result posted? You didn't pm me. :rolleyes: PM me.
Glad to see the update. :toast:Quote:
Originally Posted by EnJoY
GSkill PC4000 UCCC at 273:
http://img332.imageshack.us/img332/5...rmal8ce.th.png
Update on Patriot LLK Infineons bumped up to 267:
http://img341.imageshack.us/img341/3...7x117bn.th.png
2/18/06: Edited per TH€_BR@!N request. Sorry no validation on the UCCC and I no longer have them.
gundamit | 2x1GB Patriot LLK Infineons | 2.5-3-2-5 1T @ 267MHz | 2.67v | Link! - SPi 32M Stable: Yes
I need cpu-z validations.
You can actually see the CPU-Z validation number in the Infineon shot.Quote:
Originally Posted by EnJoY
But I don't think I did a validation for the UCCC. Maybe I'll rerun those at some point.
Pm sent for update.:D
These modules are the 5b d , that use Crucial also for the balistix model?
the diference is the 1-1 and the -4Y numbers...the rest of the codes are the same...
http://img272.imageshack.us/img272/5...wwww2bc.th.jpg
http://img24.imageshack.us/img24/9142/untitledee8ts.jpg
:)
:: Pentium M 2x1GB Results
x. Xevipiu | 2x1GB Crucial Ballistix Tracel PC4000 - Micron -5B D | 2-3-3-5 1T @ 250MHz | 2.6v | Link! - SPi 32M Stable: Yes
http://valid.x86-secret.com/show_oc?id=64238
http://img255.imageshack.us/img255/4...23353xh.th.jpg
Bye
Pentium M 2x1GB ResultsQuote:
Originally Posted by Xevipiu
x. Xevipiu | 2x1GB Crucial Ballistix Tracel PC4000 - Micron -5B D | 2-3-3-5 1T @ 251MHz | 2.6v | Link! - SPi 32M Stable: Yes
http://valid.x86-secret.com/show_oc?id=64246
http://img294.imageshack.us/img294/1...23352vc.th.jpg
Alpha0ne | 2x1GB G.Skill Extreme Series F1-4000USU2-2GBHZ - Samsung UCCC | 3-4-4-7 1T @ 280MHz | 2.72v | Link! | 32M Stable Yes
http://i16.photobucket.com/albums/b2...e/9e54158e.jpg
My OCZ EB Platinum 2GB:
freestylercs | 2x1GB OCZ PC4000EB Platinum - Infineon CE-6 | 3-3-2-8 1T @ 297MHz| 2.9v | Link! - SPi 32M/primeblend Stable: Yes
with Athlon 64
http://www.forumdeluxx.de/gallery/da...primeblend.JPG
http://www.forumdeluxx.de/gallery/da...cz_297_32M.JPG
http://www.forumdeluxx.de/gallery/da...5_298x9_1M.JPG
http://www.forumdeluxx.de/gallery/da...z_1_66V_1m.JPG
http://valid.x86-secret.com/show_oc?id=65809
free
Deleted:
Sry, didn't realise the performance of the mem controller was included.
with Multi 4 it isnt interesting.
free
how is the kingston 1gb samsung uccc? anyone use this ram ?
http://img369.imageshack.us/img369/1336/ram9tj.jpg
I just post this nice result for a friend of mine ....He ask me for the better 2x1gb kit....and I answer him Ballistix....is it right ??
:D:D
http://img68.imageshack.us/img68/315...cord1yx.th.jpg
Please, register this 3d place in chart as "playrick2001" even if it's not a registered user...or CapFTP if you can't do anything else..;)
Playrick2001 | 2x1GB Crucial Ballistix Z503 - Micron -5B D | 3-3-3-8 1T @ 306MHz | 2.9V | Link! - SPi 32M Stable: Yes
DFI nf4 Ultra-D
3700+
Air cooling
sorry Brain...we didn't made the CPuz- verification..:(
While this is for me-myself....Adata samsung UCCC+X2 4400+
http://forum.overclocklab.net/images...0x10_spi32.JPG
CapFTP | 2x1GB A-data DDR400 - Samsung UCCC | 3-4-4-8 1T @ 270MHz | 2.8V | Link! - SPi 32M Stable: Yes
DFI nf4 SLI-D
X2 4400+
Air cooling
sorry Brain...we didn't made the CPuz- verification..here too...:S
DFI NF3 Ultra + Mushkin XP PC4000 UCCC 2.7v
http://img41.imageshack.us/img41/331...024x7682wk.jpg
Hi!!
please see here my results and tweaks!!!:fact:
http://www.xtremesystems.org/forums/...ad.php?t=87394
the link now work...
`Quote:
Originally Posted by joe.latino
Its nice that you post all the screens but your not even close too 300mhz on the ram as far as i can see.
ehm...for 300mhz with this ram i should go with very hight times,so i dont think its very interesting...:rolleyes:
Well it works voor me 300mhz 3-3-3-8 TRC 11/TRFC 14 @2,81v rest of timing are fast and not lose.Quote:
Originally Posted by joe.latino
pardon but you have an Expert mb and crucial 2*1gb memory? if not...itsnt the same !!!!!
please what is your score with 3dmark05? thanks