s7e9h3n, Things are much clearer now, here's the first cold head. :banana: Now I'll have to do it again.:eek: This is for the CPU. The video head will have the 45 ell. I'll post picts. in a few:D
Printable View
s7e9h3n, Things are much clearer now, here's the first cold head. :banana: Now I'll have to do it again.:eek: This is for the CPU. The video head will have the 45 ell. I'll post picts. in a few:D
Nice little sensor array.
Here it is, head #2:bounces:
Very nice and clean!! I bet Stephen saw this and jumped in his car and is on his way to your house. LOL
Holly god! :slobber:
These evaps look soo nice! :eek:
I wish I could also make my own evaps! :(
NICE WORK! :clap: :)
PS: .... cryo: YGPM!
s7e9h3n, Will this work out for you?:cool:
CALL ME:eek:
I didn't make the evaps, chilly_1 did. I just made the plastic parts. I like his snap ring setup. It works well.Quote:
Originally Posted by 404Power
Thanks for the complement, what is YGPM?:confused: I'm only a cryo geek, give me a break;)Quote:
Originally Posted by 404Power
"You got a Private messege"Quote:
Originally Posted by cryo-tek
look in the top right hand corner for the words "Private messeges"
Thanks !Quote:
Originally Posted by zabomb4163
looking very nice cryo :D
Oh my friggin GOD. The unit looks spectacular. Can't wait to pick it up and give my hardware some hell :DQuote:
Originally Posted by cryo-tek
Need benches tbh :)
hahaha, you lucky SOB :toast:Quote:
Originally Posted by s7e9h3n
i've been starting to get the idea in my head that i should build a SS one of these days. might not be cost effective, but it'd be a fun project. building things = happy mark :D
Shall I stick my neck out here and estimate a loaded figure on both evaps?:D
Regards
John.
Professional work Cryo !
Really great ! :toast:
I'll go for -126.3 C loaded( approximately:D ), unless Cryo has been sneeky and installed check valves in the suction side;)
Regards
John.
only single card steve?
whats going to happen to your baker18 unit?
Thanks for the vote of confidence ;) It's taken quite a lot of convincing to bring the senior members' opinions of cryo-tek around. :toast: But even that estimate may be a bit far fetched as the soleniods are ~1/4A heat load themselves. We'll have to see what happens once the unit is mounted and abused :p:Quote:
Originally Posted by pythagoras
Single card has always been my preference. I'm no 3d bencher by any sense of the word. If i have to, I'll take my Baker Gpu Phase and mount it on the yonah. Then I could attempt to mount each of these heads on a pair of 7900GTX's. That'll give me -70C on the cpu with -120C on each of the video cards :DQuote:
Originally Posted by Revv23
haha then you dont know stephen :D
Excellent work u have done there cryo guy :)
Is there any chance to make a simple photo guide for us?
Perhaps with small compressor like 3/8hp?
Ha you could do a smaller 2stage autocascade tube with a 1/5hp compressor. Its just your not going to have the capacity for a large load.Quote:
Excellent work u have done there cryo guy
Is there any chance to make a simple photo guide for us?
Perhaps something small compressor like 3/8hp?
Be sure to post up some pictures of the system fully mounted and ready to go once you get her, s7e9h3n. I'm interested to see how big the final setup ends up being between system and cooling. :) Have fun with the insulation...
Think again ;) ........Quote:
Originally Posted by n00b 0f l337