Printable View
ok more info, i have the cmstacker but no it does not get stuck with the dvi screw BUT the card does rest on the southbridge.
i have a antec 550 true
i have a molex pluged in to the board, it powers up but does not give video only long beeps (i do not know if this will help but out of the 4 led at the bottom of the board only the first 3 light up)
Quote:
Originally Posted by eva2000
I use the bios on de first message of this topic on page 1.
This one:
1. LDT default set at 5x.
2. Fixed IR connection failure.
3. Fixed Boot failure when installing certain CL2 memory modules.
Get it here:
http://www.dfi.com.tw/Upload/BIOS/NF4LD201.zip
I have a strange problem- I can't change CAS Latency value in bios.
mobo work with Auto and CL2 ONLY.
If i choose CL2,5, it even not post, if CL3- it boot, restart and freeze again.
Tryed this with 2x512MB tccd, 2x256MB BH5- still same problem.
The worst thing is, if I boot-up with CL2, I can't change CL value in windows too (with A64Tweaker)- it freeze instantly.
The earlier bios (1,24/1,25) do not allow me to changing any taimings in bios, accept CL= Auto to CL=2, ANY change on other taimnigs give me no post, freeze or message "corrupted file bla-bla"
But earlier bioses allow me changing taimings in windows, including CL value.
:confused:
DFI UT NF4 SLI-D R.A00 bios- 2.09
2x512MB Patriot tccd/2x256MB BH5
winchester 3000+
PCI video
Just a little OC on Air....
http://picserver.mirror.twistspace.c...08058535//e71r
If you want to buy good memory for DFI..... buy 2x512 A-Data 566 :p: They make 300 with only 2,6V... Completely stable SuperPi/Prime. I can reach 322 3-4-4-11 too, but MemTest shows errors.
http://picserver.mirror.twistspace.c...08300359//e71r
This board like to power down completely after drastic change in ram timing...Quote:
Originally Posted by Jaan
even for those settings that store inside the cmos-reloaded i must also power the whole rig down and on it back after a while else it won't boot into windows..
corrupted file is definitely ram settings out that affect normal booting..
no problem for me w cl2 nor cl2.5 now w 0209 bios...
0201 shows tref @200mhz 3.9us
0209 shows tref @166mhz 3.9us
0209 better for tccd.
guys , have anyone noticed Hynix D43 and DFI nF4 incompatability issues? there are some people who cannot pass 210 memtest errofre e at any setting
i damn hope not......my ocz pc4200EL should hopefully run fine with this board...... :(
Hey does anyone know what the FDD connector on the middle of the board is for?
"Added stability when using SLI" or something like that DFI says.
I'm having some problems with my USB mouse, I've enabled both the keyboard and the mouse in the bios, but when booting into windows only my keyboard responds. If i pull out the mouse cable and put it in again it works, anyone know why this happens?
I did something stupid to my mobo today. I decided to try to oc the computer today, done it loads of times before, though never with a DFI mobo.
So I turned of the computer, and moved the pin so I could access 4V and 2.1V on the CPU.
Then I entered the bios and took the cpu start value to 1.45V, and then there was something else below something like VDI CPU voltage or something can't remember so I set that to 1.55V and I also changer something else to VDI * 136% or something like that. And then I restarted my computer. And now when I try to start the computer it starts for about 1/2 second and turns itself off. Please dont attack my for beeing a neewbie when it comes to DFI mobo's. Please help me.
This is what I have tried to do:
1. Moved the CMOS pin to pin 2-3 instead of 1-2 for some seconds and then back again. That didnt work.
2. Tried to move the bin which starts a safe boot or something, that didnt helt.
3. I took out the battery in the mobo and waited 15 min. That didnt work either.
you probably killed your cpu, what cooling and what cpu?Quote:
Originally Posted by furyfax
winchester 3500+, I bought it boxed. But wouldn't the mobo start even though my CPU is dead? But why is it killed? I'm not sure i understand what i did in the bios. But the board can give up to 2.1V on the CPU. So if i had switched it to 2.1V, when i restarted the computer was only on for 1/2 second, is that enough time to kill the CPU ?
check your cpu with other board 1st
2.1V :hehe:
yeah lol would like to se the 3500+ that can live with 2.1v with stock cooler :banana4:Quote:
Originally Posted by tictac
i dont have any other mobo's or money.. LOL :help:..
But did I switch to 2.1V when I did what I described en my earlier post ?
yes you switch the CPU voltage to 2.1V :hehe:
so noone has hynix D43 mem and DFI nf4 to tell us if he has met any problems?
i've got some ram im not sure if its hynix d43 or d5 but im going to test it this afternoon as i cant get my pqi tccd to work worth crap, i had it going at 240 2.5-3-3-10 and it was working great now all of the sudden it fails in memtest after about 22min
There is a broblem with my hynix d43 i have DDR500 ADATA 3 4 4 8 and i can't boot on 220 even 220x9 :eek:
Quote:
Originally Posted by brassen
I had this issue on a pre release board but not my replacement one. Make sure to use bios 209.
Nah, that's the only problem I've had with the 1/25 bios, and I don't want to try out that beta bios after all these sudden deaths.Quote:
Originally Posted by xgman
If sudden deaths were just bios related, you could rescue the board with a spare bios chip or hotflash the killed one. Obviously, this isn't the case when people suddenly have their boards completely dead, even without being able to switch them on.Quote:
Originally Posted by brassen
I also have a problem with ADATA DDR500 on the DFI NF4's.....Tried two boards and all different bios's. One for Oskar to resolve i think.
hello guys
i just purchased one of those Ultra-D :p: and i realised there is an small (but very important) bug and i'm not sure if it's cause the mobo or cause the memory controler (CPU). i can't boot with a different multiplier than 9x (i've got a a 3000+); well, i can bot a 200HTT; but not about 250+. What do you think?
i'm using the 209bios
regards!
and excuse again my english!