Printable View
The one pic was one of the first tries. Now all the chips have full contact. I won 11mhz extra. From 260 2-2-5 to 271 2-2-2-0 stable. The water have about 15 degrees. In winter time when it will be very cold outside about -20°C I will try give the bh5 -30°C. The water is phase change cooled to 15°C. Lower I have to insulate and insulating for rams is not so easy. So when it is outside cold I don't have to insulate. I hope for 280mhz :D 32M Super Pi.
Here you can see some benches:
link 1
link 2
http://img440.imageshack.us/my.php?i...agen0022sv.jpg
http://img364.imageshack.us/my.php?image=250323mu.jpg
2x512mb Geil Ultra-X Utt/Bh-5 :)
Preview Oc :cool:
Fortunately, I have a mach II gt block and a MSI Neo2 Platinum that works perfect for sitting two 80MM fans on top of the block and allowing the power cords on the right to hold the fans in place.
2x512MB TwinMos CH-5 with heatsinks
http://www.shrani.si/pics/kif_0672136217_resized.jpg
2x 80x80x15mm Zalman OP-1 fans on the plexiglass bracket
http://www.shrani.si/pics/kif_0700136225_resized.jpg
Everything installed in the Chieftec Big Dragon case:
http://www.shrani.si/pics/kif_0706136221_resized.jpg
Hey where can I get some of those heatsinks Bladesinger?
I purchased them here in Slovenia. They cost ~2 $ per piece.
In Australia, I don't have a clue.
I think they are videocard memory coolers (2 pieces came in
the box) - similar heatsinks were found on the GF2 cards :D
What brand are those heatsinks?
And dit you gain any mhz with it?
My ghetto ram under a fan. 2x256MB Nanya PC2700 @ 145MHz (2.5-3-3-7-2T)
I should really tighten down those timings, lol.
Soon to have some Crucial Ballistix.
http://www.xtremesystems.org/forums/...id=40041&stc=1
I was feeling really lazy so I just snapped the pic through my window. :slap:
About the brand - No idea :confused: As far as I recall the box just states
ram cooler - no manufacturer. If I see it in the store I will check it for you
(probably Monday).
No, havent tested it yet. Naked they did about 244 Mhz on 3.1v +.03v option
on the DFI NF4 (bios reads ~3.19v). That was memtest #5 50 pasess - can't
do more than 3.1v with my current PSU (it's a 20-pin Chieftec 420W PSU :rolleyes: ). Santa's bringing a new one :D
But I intend to run a few test in the following days if there will be enough time.
Thanks in advance dude!Quote:
Originally Posted by Bladesinger7x
Was looking for such a nice ramcooling on my 2x512mb mushkin bh-6 :banana:
El Snorro, here you go. Picture quality sucks - it was taken by a
mobile phone :rolleyes:
http://www.shrani.si/pics/slika%2824144755.jpg
http://www.shrani.si/pics/slika%2825144756.jpg
Also direct link: http://www.spirecoolers.com/hdd.asp?ProdID=37
Yaaaay, it is snowing here :D :D :D
http://users.telenet.be/taye/pics/H2O%20cooling.JPG
Don't mind the towwel at the bottom of the case. That's only temporary to avoid pump noise/vibration. I still have to find a permanant solution.
http://www.xtremesystems.org/forums/...id=40221&stc=1
http://www.xtremesystems.org/forums/...id=40222&stc=1
Cools everything down nicely. ~30cm wide, ~1000cfm, 240vAC. Oh yeah baby.
Ryan
Ok thanks so they are Spire.Quote:
Originally Posted by Bladesinger7x
Can get to that product here in Holland I think!
Thanks!
This is how I see RAM cooling.
Simple homemade blocks.
Quote:
Originally Posted by FrozenPC4Brain
I'd like to see that installed and running!! :slobber:
Did you gain anything from watercooling them? :clap:
FrozenPC4Brain
Nice idea. Looks simple too
dude - how loud?? :stick: :toast:Quote:
Originally Posted by Banzai
http://www.xtremesystems.org/forums/...6&d=113587278580mm panaflo l1a
I went with the koolance ram coolers
http://www.koolance.com/homeimage03.jpg
Quote:
Originally Posted by irev210
Did you see any improvements over air cooling?
Quote:
Originally Posted by sam3755
im using that method with a 80mm coolermaster fan
here it is...been using this conf for years now....
They aint running 100% cos that would have been overkill...lol
ramsinks used are aluminium and the fans (DELTA) are attached directly on the ram sticks with the mach 2 seal string...
Ram is OCZ 3700EB
http://briefcase.pathfinder.gr/download/267942
Sorry for bringin this old thread back up, but this is very interesting, and it would be pitty if we didn't continue it!