Aaah, I gonna try that, thanks :toast:Quote:
Originally Posted by Jack
Aaah, I gonna try that, thanks :toast:Quote:
Originally Posted by Jack
dont know why you guys are having probs.
Gigabyte K8NS Ultra 939 (F5 flashed bios)
AMD Athlon64 3000+ 939 (0.09)
Stock Heatsink Fan
Max Stable OC - Primed 15 Hours and Pied 15 times in a row
x9.0 x 272.45 = 2451.4mhz (1.488 volts)
133mhz Memory Timing stock volts
it actually works really great for a cheap setup. :)
I have some problems with 2*256mb KHX3000 BH5 Singlesided mems, what BIOS is best for my MSI K8N Neo2 Platinum 54G
Cant get realy nice FSBs out from those sticks :(
I have BOOSTER but no high FSB's
Mems do over 270FSB cas2-2-2-5 on Abit&DFI nF2 and DFI LP 250GB nF3
where can i find modded variants bios????
I've read several posts about the MSI Neo2 nforce3 having a poor chipset fan and after about a week with this sucker i'd have to agree. It gives off a high-pitched whine during operation. I had to disconnect it, it was driving me insane. Can we list this as a con of the msi neo2?
Quote:
Originally Posted by kublikhan
Too cheap for you? Can you replace it easily?
Or try ClockGen (made by same people as CPU-Z) it lets you change the HTT and the voltage, without crashing your systems like Core Center sometimes can. :mad:Quote:
Originally Posted by Dani
ClockGen
hey guyz!
I have 1 GB of A-data ddr 566 running on an ABit AV 8 in slot 3 and 4. I can´t increase RAM voltage, otherwise my pc speaker starts beeping and will never stop. only cmos reset gets stopped the beeping. I also can run it at 2,5-3-3-6 @ 1 T, if i try 2-2-2-5 @ 1T, the system boots until the user selection menu and then i get the error "0x0000008E" in a bluescreen. Memtest can´t dicover ANY single error.... :(
I AM GETTING MAD HERE!!!!!! PLZ HELLLPPP!!! :banana4:
Everything is working fine now, I got my Vcore with CoreCenter and with ClockGen, in Prime I've got 1.96V out of MSI 54G :toast:
nice :toast:Quote:
Originally Posted by Dani
and did you manage to get your memory working at ~270MHz?
Yep, but in SC mode cas2-2-2-5 blaablaablaa=tight settings :p:Quote:
Originally Posted by Jack
Can't get high FSB in DC mode with my 256mb SS BH5, tried with:
- slot1 -> KHX3000 SS BH5
- slot2 -> KHX3000 SS BH5
- slot4 -> Booster
- slot1 -> KHX3000 SS BH5
- slot3 -> KHX3000 SS BH5
..and..
- slot1 -> KHX3000 SS BH5
- slot2 -> KHX3500 DS DW50
..and then I kicked my PC and went out for beer :mad: :D
Dani, flash your motherboard with the bios F7 from the K8NSNXP-939.
It will increase the htt ;)
i dont think you wanna flash a gigabyte bios in a msi board :stick:Quote:
Originally Posted by Chouny
oooops i am tired... :banana4:
i read too fast :eek: i thought that Dani's motherboard was a gigabyte ;)
So, for gigabyte's owners, Bios F7 is increasing stable htt :toast:
if i want 300HTT, does that mean i need to put my HTT down to 2x or 2.5x? or wot?!
Some more info on MSI k8t neo2-fir via k8t800pro:
- Locks don't work. Tested both VIA-SATA and Prromise-SATA My SATA RAID-0 looses 50% of it's transfer speed after HTT 265, so I am currently limited to 2620 Mhz on my 3200+ (It would run 2800 with no worries :( ) Also AGP get's corrupted.
- Very little memory settings in bios (Using 3.2, havent found any modded bioses)
+ Takes acceptable HTT, I have clean Screenshot of 365, it even did a PiFast-run with that.
EDIT: Even with Vcore-mod I couldn't get a SuperPI with 2900, 2880 being the fastest :mad: It's a pitty, 2800 with mem in 1:1 would be nice, chip could do it with a little Vcore boost.
CP :)
after reading this review of the epox-9npa (nf4 ultra) at xbitlabs i have some questions...
as you can see, the performace of a a64 3800+ was tested at stock settings (12x200), and at 8x300 with T1 and nice timings
u might notice the bad speed compared to the good old msi nf3u, but i try to look beyond that ;) and notice how small the average performance jump is from 12x200 speeds to 8x300 speeds...
since i was planning to buy a winchester 3200+ and a nf4u, i was wondering, does the overall performance (not pifast and 3dmark alone ;)) improve from lowering the multiplier and increasing the fsb/mem? i know most people here lower their multiplier of a 3200+ from 10 to 9, sometimes even 8... but does that really improve things?
unfortunatly the review doesnt contain test at other multipliers, so the review wont be able to tell me....
but can you?
:D
Anyone tested the MSI Neo2 with the new Winbond UTT memory? I have 2 gigs of that stuff (4X512) and I'm thinking of buying this board ... I must make sure first it works though :p:
Got the ASUS SLI Deluxe today + Winchester 3200+ wait till I get Xp 120 and Mushkin RAM sticks (TCCD), i will start some serious OC.
On default with Leadtek PCX6600GT Extreme version (550/1150) 8600p in 3D Mark03 almost same scores like my old DFI nF3 250GB with 3000+ (soc.754)@2.3GHz and AGP Leadtek6600GT@575/1150 :)
Just wanted to add some info on the Soltek..
vdimm mod is the same is the nf7s and A7N nf2 boards.. same IC... tried it last night and runs fine up to 3.0v until Overvoltage protection kicks in...
board has solid vcore on mine up to 1.70 although fluctuates down to 1.68 under load...
locks do work, although the board tops out at 260 and is really only stable at around 248-250....
This board would probably love BH-5 since after doing the vdimm i still can't get it to run 2-2-2... best is 2-3-3-8
this is just some stuff ive gotten after tweaking on this thing for almost a month...
its a good solid board and has never given me grief other than the lack of a high FSB...
Hey there I have close to the same set up, Winchester 3200+, xp120, OCZ Platinum EL Rev. 2, A8n delux, Pc Power and Cooling 510 express Sli, Mitsubishi 2070sb, x800xt. I just got it all up and running today and I need some advice on how to overclock it. Any suggestions or experiance with settings that worked well would be great. Thanks!Quote:
Originally Posted by BeachKEN
Epox 9NDA3+ Update-
Newest 1/11/05 BIOS still doesn't fix the SATA Port 3/4 lock problem.
Ports 1/2 are not compatable with any of the Arctic cooling VGA coolers (6800gt in this case).
i have a problem with my neo 2:
The mainboard don't recognize my Soundblaster audigy 2 zs.I tried every pci slot with bios 1.3, 1.36 bitpower and 1.4, but nothing. I also tried another pci card, but no way. The sistem not detect.
Some one can help me :(
Not now man, one of mosfets under the ASUS heatsink was burned yesterday, so I posted the mobo for RMA. Really a big fun with this mobo, cause I was still on default (waiting for new PAPST on Xp120). :eek:Quote:
Originally Posted by m4tt
hmm... did you dissable the 'agressive timming'' option? i guess yeah... but ,,,Quote:
Originally Posted by Dani
here is my problem;
I've got the neo2 with a pair of corsair c2 rev1.4 and an OCZ booster
the first time i pluged the booster it was set to 3.9V (i though it was set in the min.) and if i 'insert' a part in the 4º (where the booster was) slot of the mobo it doesn't boot :confused:.
i told that the mobo doesen't boot with a part in the 4º slot to the guy of the shop (trying him to change it for a new one) and this guy said "that's normal, cause the 4º slot is not the recomended for only a Dimm :eek: , you gotta check your mobo's manual to se...."
is that :banana::banana::banana::banana: true? or this guy was only kidding me?
cheers :toast:
PS: sorry 4 my english is not so good....