X1800 Xl = Wow!

Printable View

Show 100 post(s) from this thread on one page

02-13-2006, 12:08 PM
vassmar

Quote:

Originally Posted by Kriller

I tested my HIS XL before, 650,70 / 630 with stock cooler and 1,2v. I don't think I will go higher, the temps are really high. I'll pu my waterblock on it tomorrow. I got 9334 3dmarks on my 24/7 config (that is alot of services an cpu at 11x250)

I don't understand why my mems clocks so bad, 650 gives alot of artis in windows, and 700 is messed up =) I suspect that I may have 1,6ns chips or that the timings are too tight. I am using ATI-Tool.

Dunno if it will be any help, but I also got the HIS, but with the 1.4ns mems tho, and I had the same problem with the artis at the rams. But when i increased the volts they basicly disappeared, atleast up to 680mhz, but I didn't go any higher cous I was using the stock cooler.
Don't remember exactly what the volts was, but try to just pump them up abit at the time and see what happens, maybe it works, maybe not ;)

I'll fit a copper cpu cooler at my card this week, so hopefully i'll do better than my previous scores/clocks. :D
02-13-2006, 12:12 PM
deathman20

Hey curious has anyone seen a bios editor so we can set voltages/clocks at bootup? I'd love one think it would be less stressful on the card also.
02-13-2006, 05:28 PM
tvdang7

ok i got ram sinks on my mem and my regulators and yet my regulator temps have went up 2-3..............wierd....

maybe my room was warmer this time around..... but it got my paranoid.
02-15-2006, 03:57 PM
deathman20

Yay moving up on my score :)

http://service.futuremark.com/compare?3dm06=131222
02-15-2006, 04:22 PM
tvdang7

hey is yalls ram hot? mine isnt warm
02-15-2006, 07:49 PM
deathman20

Hot lol, mines cool. I had a thermal probe on it and it was bearly warmer then the case tempature on the heatsink so add about 10C and thats what the real temp of the chip is. So mine runs ~ between 45-55C
02-15-2006, 08:21 PM
tvdang7

my x800 XT ram chips were so hot i couldnt touch em for more than 5 seconds.

y do these run so cool?

1 more problem.

In bf2 my frame rates go to crap. i dont get it. im 100% sure its overclock related. im lik 40-50 sometimes i dip into the 35's sometimes. but when im on stock settings its like 60+ all the time. are my regulators not regulating? i got a fan blowing on it already with heatsinks on em copper ones too.
02-15-2006, 11:33 PM
don_vercetti

Quote:

Originally Posted by deathman20

Hot lol, mines cool. I had a thermal probe on it and it was bearly warmer then the case tempature on the heatsink so add about 10C and thats what the real temp of the chip is. So mine runs ~ between 45-55C

do you run them naked? Or do i read that you have heatsinks on them..
02-16-2006, 06:49 AM
deathman20

Quote:

Originally Posted by don_vercetti

do you run them naked? Or do i read that you have heatsinks on them..

No they got a heatsink on them.
02-16-2006, 06:50 AM
tvdang7

i have copper heatsinks on them and a fan blowing on it.
02-16-2006, 07:36 AM
Kriller

Quote:

Originally Posted by vassmar

Dunno if it will be any help, but I also got the HIS, but with the 1.4ns mems tho, and I had the same problem with the artis at the rams. But when i increased the volts they basicly disappeared, atleast up to 680mhz, but I didn't go any higher cous I was using the stock cooler.
Don't remember exactly what the volts was, but try to just pump them up abit at the time and see what happens, maybe it works, maybe not ;)

I'll fit a copper cpu cooler at my card this week, so hopefully i'll do better than my previous scores/clocks. :D

I will try that! Still on the stock cooler thou, but a new maze4 on the way.

What scores do you got? I have 9500/17800/37600 in 05/03/01, with only the stock cooler, no extra fan. I can get higher scores, but the core runs so darn hot so I'll wait for the water...
02-16-2006, 07:47 AM
don_vercetti

I'm running the RAM nekkid, it's currently doing 600mhz 1.9v. Haven't tried higher, either. Scoring 8972 in 05 at 625/600. Very nice card.
02-16-2006, 02:02 PM
vassmar

Quote:

Originally Posted by Kriller

I will try that! Still on the stock cooler thou, but a new maze4 on the way.

What scores do you got? I have 9500/17800/37600 in 05/03/01, with only the stock cooler, no extra fan. I can get higher scores, but the core runs so darn hot so I'll wait for the water...

Gonna be sweet with the maze4 :D

I have only benched 05 yet, when the card was new in december, becasue i've been too lazy to try all progs. :P
But anyway... i got 9162 @ 621/688 (stock cooler). Cpu was at 2.7ghz and rams at "too slow speed (192Mhz)", i can't run them over 210Mhz with my DFI mobo and that's not very good...

But as I've mentioned before, I'll fit a new cooler soon and then I'll run thru all the 3dmarks, the card can defently go higher than my previous clocks with some more testing and better cooling.
I'll post the results as I go...

btw, those scores are pretty nice for a stock cooler ;)
02-19-2006, 10:27 PM
tvdang7

man this thread gonna die soon since hte x1800 is discontinued now. .......

guess its been a good stong thread for this series.
02-20-2006, 01:21 AM
Kriller

Anyone knows when X1900XL arrives? And the speccs?

My new maze4 is probably here in one hour or so :D My XL idle at insane temps with the stock cooler (and clocks), over 60 degress is standard when the fan is controlled by the card, I have checked the contact on the cooler, and it seems fine, I had much better temps with the thermal pad than the as3...
02-20-2006, 05:50 AM
JonnyCTX

http://img380.imageshack.us/img380/2880/98001lw.jpg

That's the most i'm gona get the card to i think :(:(

1.175v through the core, any more and it crashes!!!

Zalman VF-700 CU + Thermalright XP-120 for cpu

all air!
02-20-2006, 06:02 AM
Kriller

Weird with the core-voltage, lucky you that got good ram-chips! Isn't your score a little low btw?

check my 9585: http://service.futuremark.com/compare?3dm05=1803037
02-20-2006, 06:04 AM
deathman20

Quote:

Originally Posted by JonnyCTX

That's the most i'm gona get the card to i think :(:(

1.175v through the core, any more and it crashes!!!

Zalman VF-700 CU + Thermalright XP-120 for cpu

all air!

Congrats there man. Your right up there with me in my highest of clocks. But that is an sweet OC for such a low V. Wish I was that lucky.

http://service.futuremark.com/compare?3dm05=1814021

Comparison this is one I did recently but still need to move up the OC on the core for max. The 6.2 drivers allowed me to downclock my OC 25Mhz on the core and still came ahead on the score from my previous one. Just wish I could hit 650 like I did one time I did way back, must of been some very cool day.
02-20-2006, 06:05 AM
JonnyCTX

Quote:

Originally Posted by Kriller

Weird with the core-voltage, lucky you that got good ram-chips! Isn't your score a little low btw?

check my 9585: http://service.futuremark.com/compare?3dm05=1803037

Why do you think that the score is low? Should it have got much higher at those clocks?
02-20-2006, 06:08 AM
deathman20

Quote:

Originally Posted by JonnyCTX

Why do you think that the score is low? Should it have got much higher at those clocks?

I'd say your score is almost right on. Maybe some background apps could be throwing it off but I think its right for the range.
02-20-2006, 08:07 AM
LowRun

1 Attachment(s)

Quote:

Originally Posted by JonnyCTX

Why do you think that the score is low? Should it have got much higher at those clocks?

We pretty much step on each other's feet there.
02-24-2006, 06:14 AM
Stelios

1.275VGpu , 2.05Vmem . X1800XL with zalman V700CU.

No tweaking , no LOD . :)
CPU can ran 3300+Mhz on a single stage .
02-24-2006, 08:51 AM
tvdang7

man yall making me jelous. i cant(dont want more volts than already) go high than 675 on ram. but i have 1.6 chips tho.

can some one answer this.

in ati tool if i click the auto overclock thing it goes really high like i can hit 700 before it crashes but if i set it my self to like 680 or so it crashes. same with core auto goes to around 680-700 but if i do 660 manual it crashes instantly.
02-24-2006, 09:01 AM
deathman20

I'm jelous to all who can pump more then 1.225V in it for any stable period of time and still get a good OC out of the card. I run so much cooler then some with just a tad higher voltage and yet they can still hit the high OC's. Grrr.
02-24-2006, 09:38 AM
OV3RCLOCK3R

I got hold of Jonny boy's x1800xl card:D

But need some help, When using overclocker, i can set my ram clock to 700 (1.4ghz) easily but when using Ati tool, if i set it to 700, Instantly, lots of artifacts appear on the screen and then the system BSODS although through overclocker, 1.4ghz is fine and i can game for hours at that speed.

Can anyone tell me what this is happening and i have the 1.4ns ram:)
02-24-2006, 10:11 AM
don_vercetti

simple, overclocker loosens the timings. ATItool doesn't.

And Deathman, if i try to 'pump' 1.15v into my card, i get a crash. And this is watercooled, with plenty of fannage, in an ambient temp of 10-15c.
02-24-2006, 01:32 PM
deathman20

You have to up the voltage on the memory. 2.0-2.15V is where I see some peoples cards hitting the 700 mark (mines just under 2.1V). Also crank up the MVVDQ to 2V at least, and move it higher if need be later. As don_vercetti said, Overclocker looses timings. I could hit 830Mhz on stock voltages, yet running at 700Mhz through ATITool yielded me nearly a 600point gain in 05 tests on the first set of drivers that was out for the card.
02-24-2006, 01:34 PM
deathman20

Quote:

Originally Posted by don_vercetti

simple, overclocker loosens the timings. ATItool doesn't.

And Deathman, if i try to 'pump' 1.15v into my card, i get a crash. And this is watercooled, with plenty of fannage, in an ambient temp of 10-15c.

It sucks doesn't it? That you can't put more in and yet you know you have more then enough cooling.
02-24-2006, 01:41 PM
don_vercetti

Damn straight. In the current british weather and my 120.3, it keeps the card down to around 30c core. 30c!!!!!! And that's loaded as well.

And the core goes up to 610 on stock, going to 1.125 gets me to around 645, and i can't go higher! It is unbelievably frustrating.

Happily, my RAM can reach about 670mhz with 1.95v, and i haven't tried higher, so not all is lost.
02-24-2006, 02:21 PM
deathman20

Doing very well on the core and ram at least mine gets around that speed on core with 1.25V and memory takes about 2.0V to get that fast so you definatly got room on the ram at least.
02-24-2006, 02:40 PM
don_vercetti

yeah.

Any word on BIOS flashing helping out with more voltage? Or anyway of soldering on the missing mosfet, to help out the power regs a bit?
02-24-2006, 02:41 PM
don_vercetti

Sorry, double post. Connection went a bit screwy.
02-24-2006, 06:37 PM
sickness

When you guys use Overclocker.exe, are you able to use the 2D clocks/3D clocks radio buttons? I see some people able to use them but they are disabled for me.
02-24-2006, 07:44 PM
OV3RCLOCK3R

Quote:

Originally Posted by sickness

When you guys use Overclocker.exe, are you able to use the 2D clocks/3D clocks radio buttons? I see some people able to use them but they are disabled for me.

X1800Xl doesnt have 2d/3d clocks:(:stick:
02-24-2006, 08:53 PM
deathman20

Quote:

Originally Posted by don_vercetti

yeah.

Any word on BIOS flashing helping out with more voltage? Or anyway of soldering on the missing mosfet, to help out the power regs a bit?

Viperjon did something with his card that really upped the possibilites of more voltage. Truely if someone had a dead XL or XT laying around and you could do some sodering im sure you could get an extra power regulator on the board if all the traces are there.

Oh besides bios flash I'd love to get one where I could actually enter my clock speed from default. That would be really nice.
02-24-2006, 08:57 PM
deathman20

Quote:

Originally Posted by OV3RCLOCK3R

X1800Xl doesnt have 2d/3d clocks:(:stick:

Yup doesn't need it as much as the XT's did because its using so much less power.
02-24-2006, 11:48 PM
don_vercetti

Quote:

Originally Posted by deathman20

Viperjon did something with his card that really upped the possibilites of more voltage. Truely if someone had a dead XL or XT laying around and you could do some sodering im sure you could get an extra power regulator on the board if all the traces are there.

Oh besides bios flash I'd love to get one where I could actually enter my clock speed from default. That would be really nice.

hmmm. It would be worth doing, imho. Think of this, the default voltage of the x1800xl is 1.075v, where the x1800xt is 1.3v. And the X1800XT has 6 regs, while the x1800xl has 5.
Now if we work out 5/6ths of 1.3v...we get 1.083...which is almost exactly the voltage of the x1800xl.

Therefore, i would imagine soldering a sixth one on would seriously help the voltage situation...right?

Time to find a dead x1800.....
02-25-2006, 03:32 AM
persivore

Quote:

Originally Posted by don_vercetti

hmmm. It would be worth doing, imho. Think of this, the default voltage of the x1800xl is 1.075v, where the x1800xt is 1.3v. And the X1800XT has 6 regs, while the x1800xl has 5.
Now if we work out 5/6ths of 1.3v...we get 1.083...which is almost exactly the voltage of the x1800xl.

Therefore, i would imagine soldering a sixth one on would seriously help the voltage situation...right?

Time to find a dead x1800.....

The missing MOSFET and inductor pair on the X1800XL is for the Vdd supply iirc. The Vgpu uses a 3 phase regulator, which is the same as the XT cards. The MOSFETs on the cards are BGA types, so it might be quite difficult to add the missing MOSFET without the correct tools.
02-25-2006, 03:41 AM
don_vercetti

oh ok
there go my hopes, blasted into smoke.
02-25-2006, 08:13 AM
deathman20

Quote:

Originally Posted by persivore

The missing MOSFET and inductor pair on the X1800XL is for the Vdd supply iirc. The Vgpu uses a 3 phase regulator, which is the same as the XT cards. The MOSFETs on the cards are BGA types, so it might be quite difficult to add the missing MOSFET without the correct tools.

WHere did you find that bit of info?
02-25-2006, 08:45 AM
OV3RCLOCK3R

Quote:

Originally Posted by deathman20

WHere did you find that bit of info?

I would like to know aswell:)

Didn't some of the first X1800XT's have 5 power mosfets aswell?
02-25-2006, 08:51 AM
deathman20

Ya I think some of the first XT's did just have 5. But well 6 is always better then 5 :)
02-25-2006, 09:09 AM
persivore

I've just checked on my card again, and the missing MOSFET/inductor pair are for Vgpu. The XT's have a 4 phase Vgpu supply, and the XL's have a 3 phase supply. The other 2 MOSFET/inductor pairs are for the Vdd/Vddq supplies.

There might still be some hope that adding the missing phase might help increase the overclock, but i'm not confident that it will increase the GPU's voltage tolerance. I think that it is more down to the A14 core revision, and the problems ATI had producing the R520 cores.

The best way to work out if the extra Vgpu phase will help the voltage tolerance of the GPU would be to look at the XT cards with the missing 4th phase.
02-25-2006, 09:14 AM
deathman20

There is hope :) Wahoo :)

But of course its all limited on the A14 revision but its always worth a try.
02-25-2006, 09:17 AM
OV3RCLOCK3R

Quote:

Originally Posted by deathman20

There is hope :) Wahoo :)

But of course its all limited on the A14 revision but its always worth a try.

I've noticed that that where the missing reg is, there are some other missing stuff aswell, on the back of the card
02-25-2006, 09:20 AM
don_vercetti

Quote:

Originally Posted by persivore

I've just checked on my card again, and the missing MOSFET/inductor pair are for Vgpu. The XT's have a 4 phase Vgpu supply, and the XL's have a 3 phase supply. The other 2 MOSFET/inductor pairs are for the Vdd/Vddq supplies.

There might still be some hope that adding the missing phase might help increase the overclock, but i'm not confident that it will increase the GPU's voltage tolerance. I think that it is more down to the A14 core revision, and the problems ATI had producing the R520 cores.

The best way to work out if the extra Vgpu phase will help the voltage tolerance of the GPU would be to look at the XT cards with the missing 4th phase.

So just to get it straight, if i were to find an old, dead, x1800, i could remove one mosfet and the two inductors on the other side, solder them on, and it would at least work?

Since i wouldn't imagine the risk to be too high, i'd say it's certainly worth a try.

EDIT

looking at the back of the card, i can see Overclockers right. We're also missing some transistors from there as well.

So, anyone got a dead x1800 they'd donate to the cause? Or know where i can get these Pulse mosfets from? And the accompanying inductors, of course.
02-25-2006, 09:40 AM
cadaveca

lol. I've made a mod already to one XL..and persivore is right...the missing inductprs belong to ram volts, and nothing else. you also need the 256mb bios, which i have been trying to get....
02-25-2006, 10:03 AM
persivore

Quote:

Originally Posted by don_vercetti

So just to get it straight, if i were to find an old, dead, x1800, i could remove one mosfet and the two inductors on the other side, solder them on, and it would at least work?

Since i wouldn't imagine the risk to be too high, i'd say it's certainly worth a try.

There might be some other components which would need to be added, such as resistors between the Vgpu regulator and the the MOSFETs gates and current sensing resistors. You might also need to remove parts from the card, to indicate to the Vgpu regulator that the 4th phase is present too. It would probably be easiest to compare a card with 4 phase Vgpu to a card with only 3 to work out which components are missing.

Quote:

Originally Posted by cadaveca

lol. I've made a mod already to one XL..and persivore is right...the missing inductprs belong to ram volts, and nothing else. you also need the 256mb bios, which i have been trying to get....

What mods have you done to your card? Are you sure that the missing components belong to the RAM supply? It looks like the missing components are for the Vgpu regulator after checking on my card :confused:
02-25-2006, 10:26 AM
cadaveca

hmm....gpu volts? maybe that's why i never saw a change.

i've added all the components besides the silicon/germanium whatever it is.

i can laugh at myself now...of course there was no change.

what is that, persivore? I only have an idea as to what it does, not what it really is. I have xl, xt and x19xt, xl has no power-jump, so i figured the xtra phase might have something to do with it. heh. soldered the stuff on i could, and there was no change....

lol

so i thought it was for ram power...

lol
03-04-2006, 01:48 AM
Ig]N[iS

Hi all,
I'm waiting for a Sapphire X1800XL to arrive... I have already bought an AquagrATIx 1800 (a waterblock made for x1800) to cool it with my water cooling system.
1) I've read about two versions of this VGA : A14 & A15... what's the difference between them? and how can i know which type is mine?

2) To rise up ur voltages u use the overclocker.exe or Ati tool? I ask it because i read that overclocker's voltages are not always the true voltages...

Waiting for ur reply ;)
03-04-2006, 02:46 AM
Kriller

Just use ATI-Tool, it doesnt change the timings and the voltage options works fine.
03-04-2006, 04:11 AM
Ig]N[iS

and for the memory voltage u rise MVDDC & MVDDQ from ATItool at the same time? I have to rise them togheter?
03-05-2006, 11:40 AM
Aerou

Im just confused with the voltages,
which one works and is "true"? atitool or overclocker???
when I adjust mem voltages in overclocker atitool shows them, but when I adjust voltages in atitool overclocker shows them at its the default :stick:
I think it will be DMM time!
03-05-2006, 02:26 PM
Ig]N[iS

I knew that u have to adjust them from che ATI tool, but which mem volt i have to rise? MVDDC or MVDDQ???
03-05-2006, 08:57 PM
OV3RCLOCK3R

Quote:

Originally Posted by Ig]N[iS

I knew that u have to adjust them from che ATI tool, but which mem volt i have to rise? MVDDC or MVDDQ???

MVDDC:)
03-05-2006, 09:21 PM
Henry

Here's my X1800XL 3DMark05 score :

http://service.futuremark.com/compare?3dm05=1859960 = 10.035 pts.

That's with 670/729 (1.275v/2.1v), stock cooling.
03-06-2006, 01:24 AM
Ig]N[iS

where as...what is the MVDDQ??
03-11-2006, 06:14 PM
OV3RCLOCK3R

Is it only my card or does it happen to anyone else's aswell?

If i set the vgpu volts anything over 1.150v, anything 3d and it freezes so 1.150v is my limit. Does this happen to anyone else?
03-11-2006, 06:57 PM
deathman20

Quote:

Originally Posted by OV3RCLOCK3R

Is it only my card or does it happen to anyone else's aswell?

If i set the vgpu volts anything over 1.150v, anything 3d and it freezes so 1.150v is my limit. Does this happen to anyone else?

This is because of either the power source (the volt regulators) or the chip itself can't handle the high voltage. I've seen a few that can't take it over 1.15V and some have taken it quiet a bit higher. I top out at 1.225, and can hit 1.25 for 3D mark runs some times.
03-11-2006, 07:27 PM
OV3RCLOCK3R

Quote:

Originally Posted by deathman20

This is because of either the power source (the volt regulators) or the chip itself can't handle the high voltage. I've seen a few that can't take it over 1.15V and some have taken it quiet a bit higher. I top out at 1.225, and can hit 1.25 for 3D mark runs some times.

Kewl, Thanks for help and does MVDDQ voltage help with anything?:confused:
03-11-2006, 09:22 PM
perkam

Lets keep this thread alive until end of march :p Buyer sof the X1800GTO (aka 12 pipe X1800XL) will need all the help they can get to get their cards to break 600 on their mem and GPU :)

Perkam
03-12-2006, 09:52 AM
deathman20

Quote:

Originally Posted by OV3RCLOCK3R

Kewl, Thanks for help and does MVDDQ voltage help with anything?:confused:

MVDDQ deals with the ram. It helps out on higher clocks thats basically all I know on that, but making sure that the MVDDQ does not go above MVDDC. All I've found so far is that would be a bad thing and would likely damage the memory.
03-27-2006, 07:48 PM
Pyr0

anyone know of a software app that works in windows x64 to change voltages on an X1800 series card ?
03-27-2006, 10:18 PM
RyderOCZ

Good explanation here about what the voltages are: http://forums.techpowerup.com/showpo...&postcount=135
04-04-2006, 03:54 AM
Kashelz

Here are some results of my Sapphire X1800XL 256Mb VIVO with 1.4ns memory! Memory overclocked nice, first with lower core I was able to test 720Mhz, but with higher core frequency of 656Mhz memory went to 769 :D Best I coud get stable for benching was 656/769 (1539)!

http://foto.apollo.lv/files/Kashelz/large/189688.jpg

My achievements:
3DMark03 18732 from ~ 14400!
http://foto.apollo.lv/files/Kashelz/large/189695.jpg

3DMark05 10282 from ~ 7590!
http://foto.apollo.lv/files/Kashelz/large/189696.jpg

3DMark06 4439 from ~ 3250!
http://foto.apollo.lv/files/Kashelz/large/189697.jpg
04-04-2006, 08:30 AM
deathman20

Nice improvement :)

What type of voltage you using? I'm really curious about how much you are putting into the memory since I know mine can hit 730 relatively easy, and 700 is a piece of cake.
04-04-2006, 09:58 AM
Kashelz

You can se my voltages in pictures ;)

But Ok, Im useing something like this:
VGPU: 1.225v
MVDDC: 2.315v
MVDDQ: 2.050v

Memory is interesting thing, when my core is @ 500 Mhz, max memory 715 - 720, when my core is at 650, then memory goes to 769, strange, but interesting! Dont know if I need so high votage with high core fruequency! For first testing I overclocked core and memory separately! Here what coud I get with what voltage:

Code:

1 min ATITool 0.25 b14 3D stabile for lockups! VGPU Core GPU Overclock Mhz 1.075v 550 1.100v 575 1.125v 594 1.150v 610 1.175v 630 1.200v 640 1.225v 659 * 1.250v 675 * 1.275v 685 1.300v 702 1.325v --- 1 min ATITool 0.25 b12 Artifacts free/3D stabile for lockups! MVDDC/MVDDQ Mem Overclock Mhz 1.889v/1.889v 549 1.903v/1.903v 567 1.930v/1.930v 571.5 1.957v/1.957v 580 1.985v/1.985v 585 2.012v/2.012v 589.5 2.039v/2.039v 594 2.067v/2.067v 594 ---- 2.302v/2.151v 706.5 2.302v/2.004v 720 2.250v/2.004v 706.5

Tested memory till 2.067v/2.067v, then I puted high votage and looked were can I get - become boring for me :slap: Maybe I can get lower, I hope so, but for testing, not 24/7 usage its ok! And it will not hurt mem chips, if they ar cooled well :)

Now I should look what can I get stabile for 24/7 usage, core sometimes goes to 670 ok or even more for some time, sometimes not, damn that they are A14 ones:nono:
05-04-2006, 09:07 AM
KoHaN69

hey guys, i got a connect3d x1800 gto flashed to 16 pipes
same lock up 1t 1.2v on the core,
I'm tryin to push the ram now

700mhz @ 2.2v mem, i/o: 2.0v

Running on stock heatsink, with the fan 100% duty and another 20mm fan blowin at the voltage regulaotrs at full speed.

I was posting in this thread earlier:

http://www.xtremesystems.org/forums/...44#post1432644

http://www.xtremesystems.org/forums/...ad.php?t=94602
05-04-2006, 12:28 PM
KoHaN69

Quote:

Originally Posted by Pedro Rocha

I just mount 1 Gecube X1800XL for testing, where is what I got with stock cooling :

http://pedrorocha.planetaclix.pt/X18...ark05_9706.jpg

Not bad at all :) , with the Zalman I should see some improvements but it is just a test card before my X1800XT cards arrive ..

DAMN!!!

i GOT my gto (16, like xl) cant do past 1.11v on the core
how did u manage 1.225?

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 07:14 AM.

XtremeSystems