Printable View
I'm saying good because it's not like the 0536VPAW's and I've seen 2 that will do at least 3.3-3.4 under single phase. Also the one I have will do about the same as my other two. Haven't burned it enough to know where it will end up. As you know even within the same week and stepping there is a top and bottom, so far the bottom isn't that bad. Time will tell.Quote:
Originally Posted by gundamit
Please, no punds at 6:04am :nono: , save them for pm only. :D
i think it's time to make an official database thread with all the oc results organized neatly. what shall be the requirement for getting in?
32M Stable, Tweaker Shot and CPU-Z validation. AIr, Water and Phase categories. :)
sounds good. who has enough time to maintain it? :D
Can anyone fill me in on what seems to be the *best* 2x512 ram solution for this processor on a DFI NF4-Ultra?
Thanks....I was able to hit 3ghz on my crappy ram with a MAJOR div unstable, so I'm thinking it's time to upgrade my ram!
What you guys think I should expect from a 148 CABYE 0536GPMW with a good air cooling?
first clock on opteron 144 cabge under cascade -90
hard to boot at 240 fsb 1.7 vcore on giga k8nsnxp-939, and freeze in windows at 245 :/
this opteron sux a lot :o
on air prime all the night at 1.7 vcore 292 x 9 , and boot at 270 x9
:/
Quote:
Originally Posted by freestylercs
Hey can you tell us how is your 148 going so far?
Quote:
Originally Posted by Rohan
Thats not correct: Try this: Setup at BIOS to 1.535V. Then cinfigure with clockgen 1.45V, ya will see with CPU-Z that ya will get 1.58 to 1.616V
Just order a 146 from overclockers.de they are in stock.
Hope its a goooood one
We havent got the Opterons here in Denmark yet.Quote:
Originally Posted by dinos22
Just ordered one from Germany. Dont know the stepping though.
opteron 148 w/ 2x1GB Ballistix DDR 500 , dfi ultra D w/ 7-04 bios
havent really had a chance to really tweak my memory, but it's surely a great start!
cpu temps are at around 39C
http://kwago.com/crap/opteron%20148%20at%202926mhz.GIF
Hi guys. Very stupid question I'm sure but after briefly skimming the thread here, I am still unsure the the Opterons are multi locked or not.
Are they able to go downward in multis?
Thanks!
These Opterons look fantastic. Makes me want to hold off my dual opteron build.
Didn't look at folks locations reading this thread, any Canadian members with info of retailers? NCIX has the 144 listed and shipping early next week.
@BLHealthy4life: Yes they are able to go downwards in multi's
@skirms_fr: what cpu did you have in your mobo before and what was the max HTT you hit with that? What kind of RAM are you running and are you using a divider? I'm not sure what kind of results to expect with cascade so I cannot comment on the performence of subzero temps.
before i have a winni 0448 spmw 360 x 9 max screen with bh5@ 3.85Quote:
Originally Posted by asianguy80
how is that motherboard working out for you?.... i am still waiting for my 146 to come from upgrade source. they wont be in till the 25, but i am still looking for a good agp board to put this processor onQuote:
Originally Posted by mbm
Its working OK. Doing 255x10 at 1:1 (2.5-3-3-10-1T)Quote:
Originally Posted by Naasar
People are hitting 300mhz FSB and some close to 400mhz.
I dont see it as a super OC board though. I bought it because of the AGP and PCI-E combo. If I had a PCI-E card I would get another board.
exactly why i asked. i have a x800xl agp and dont want to buy another card. did u do any mods to it?Quote:
Originally Posted by mbm
yeah they are only uplockedQuote:
Originally Posted by BLHealthy4life
with some ram that does higher mhz, i'm sure i could change the divider to 166mhz for a higher ram clock, but i finally got around to doing some real tweaking. how much more do you guys think i can get out of it? :D
http://www.xtremesystems.org/forums/...id=38593&stc=1
(btw, this is with 2x512mb ballistix, one is sorta dead, gives lots of errors in one spot ;))
(also remember that this used to be my max 1m without resorting to chilled water: http://eclipseoc.com/phpwcms_filestorage/1/1_42.png)
Ive done the Vcore mod. But it didnt gave me extra OC. Im running at 1,45V now.Quote:
Originally Posted by Naasar
whats the max load a 48 cabye should be running at? I am at 1.44v, 2900 and 40c idle 58c load :/
58c is high... but, these Opterons are by far the hotest AMD chips I've ever used, in fact, only my old 3.4 Prescott would run up the temps higher.Quote:
Originally Posted by ocZZ
With my water cooling setup I have seen load temps hit 55c... although that was at nearly 1.6v.
I'd suggest you look into upgrading your cooling system.
ouch. took me 1.55v on the stock cooler to get ~62c load temps.Quote:
Originally Posted by ocZZ
they are multi locked upwards like all the other CPUs besides FXQuote:
Originally Posted by BLHealthy4life
Where can the the 148's be had for under 300 dogs? The only one I know of is 318.
146 CABNE0530APMW 2800Mhz 1,232Vc Aircooling TR XP90 Ambient 16°C 24H Prime Custom FFTs i.pl.
http://img425.imageshack.us/img425/7...mffts24.th.jpg
i was doing some testing last night and noticed my hard drive temps were 22C heheheh i remembered your ones Rufus
great CPU btw
That worked with my Winchester, but with my opteron, the FID/VID controls are greyed out in clockgen. Anyone else notice this?Quote:
Originally Posted by Slipknot
And here is the little Pic from the Temperature.
http://img444.imageshack.us/img444/651/bild239ta.th.jpg
And with 2815Mhz 1,232Vcore is Prime still running since the 24Hour Screen at 2800Mhz.
http://img293.imageshack.us/img293/9...m26h5lr.th.jpg :banana:
Thx Dinos22,bought a new Cooler. TR SI 120 .Tommorow i will test the cooler.
yup, same problem for me. clockgen probably just has to be updated to support the opteron :DQuote:
Originally Posted by Rohan
EWIZ sell it for 285Quote:
Originally Posted by gbomb944
Or you can Try with Systool v0.1 build 617.Quote:
Originally Posted by ozzimark
Hey all, I have a humble request (which you may obviously completely disregard). As more and more of us get Opterons, it gets harder to track everyones names. So even though you stated your stepping 8 pages ago, I have completely forgotten it by the time you post your awesome screenshots! Me too dumb too merember evybodie! Would it be reasonable to request that steppings/weeks be posted above any screenshots? No big deal if you think it is. Anywho, thanks for helping me (or sorry for the inappropriate imposition of my will, pick the one that works for you).
G.Skills are here!!! Tweaking for stability; once they're kosher I'll get some results up. Stupid nF3 board - total drag.
http://store.sun.com/CMTemplate/CESe...P&catid=131490
Depending on the mobo options I guess you could move a different 939 into the workstation. I've always thought Sun boxes look cool with the big logo on the side. The top is a little square but with some ccfl's behind that front panel it would be sweet.
Got my Opty 148 to run 3Dmark'01 @ 3102Mhz on air cooling.
Not exactly a high powered video card though... :p:
http://service.futuremark.com/compare?2k1=8753330
I attached a screen shot of CPU-z. This was not taken at the same time as the 3Dmark score. 3dmark needs at least 1.58 to stabilize.
Although 1.5Vcore will let me do everything in windows (files, surf, etc.)
Cabne 0528 gpmw
i think it's a good idea.. though an even better one would be for someone who has the time and patience to keep track of it to start the "official oc database" with links to various speeds in different stepping categories :DQuote:
Originally Posted by ixtapalapaquetl
Perhaps dogsx2 may change his very first post to include an opteron rank with steppings, names, volts, bios, etc...
It shoud be a great improvement to this thread!
Yep. my (aaustralian) opty 144 CABYE 0536 is doing 3ghz w/ 1.6V on an an8 ultra.
isso é que era de valor meu amigo brazuka :toast:Quote:
Originally Posted by RafaDel
i think that too.
i lost hours to find some post about steepings and results only in this tread!!! :mad:
My final prime screenshot. apmw 0530 batch 0052 without heatspreader.
24/7 settings:
http://www.forumdeluxx.de/gallery/da...5302870S24.JPG
Thanks, Systool works great for changing VID on my opteron. I can get the max vcore now :)Quote:
Originally Posted by Rufus7
hey Riverna, i think i love that wallpaper you got there on your screenshot? you mind posting it? or letting me know where i can find those and others? thanks homie
ps: nice oc, >1.4v pwns
el rolio,
Look here.
why thank you dear sir. :DQuote:
Originally Posted by largon
see if i can find some widescreen lovin'
Its really hard to stop playing with this CPU! I think I just nudged my way on to the XS 3DMark '05 top ten list.
http://img425.imageshack.us/img425/3...40stock6bt.png
http://service.futuremark.com/compare?3dm05=1323773
Cant find a opteron wallpaper?
haha that's what I was thinking.Quote:
Originally Posted by mbm
Good job, :thumbsup: you keep playing with it and who knows how high your little opty and a pair of 7800gt's will end up.Quote:
Originally Posted by gundamit
These seem to be doing great... hopefully i'll get one soon!
Thanks. I keep thinking the 146 might end up being the strongest though. I just need to find more seal string and I'll switch again and give the 146 a crack at sub-zero. I'll try an auto glass place today to see if they have something simillar to the seal string for the Prommie.Quote:
Originally Posted by dogsx2
Speaking of the Prommie ... I popped the front of my Mach 2 open and strapped a 120mm to push more air through it, and it seems to be helping a little, but it still looks like cooling might be the limiting factor as usual.
Hi guys,
next week I will have an opteron 146 (boxed version)... If I reach good results, you will know. :D
I hope that my neo 2 platinum an my pqi memory will work with the opty without any problems... :) (:party2: )
Bye!
Here is a screen from my 148 (CABNE 0528).
http://img364.imageshack.us/img364/5...superpi9jc.png
The temp above is under load. I don't think I'm going to go any higher until I get water cooling. Will probably even back off some.
man the temp aint bad at all
Good call. I'm really liking your memory. Makes me want to buy a new pair just to bench with. :)Quote:
Originally Posted by ixtapalapaquetl
@ixtapalapaquetl:
Great results!. For 306Mhz, what about your MAL and RPT (read preamble)?
Well, some initial results from my new opteron...
It was a 148 0528 CABYE from ewiz.
When I got this chip, I was in the middle of a entire system rebuild. I moved from a Lanparty754 and mobile 3400 @ 2.7ghz to the 939 Optie. Also upgraded my waterblock from a Maze3 to Storm. I had big plans. :banana:
I am using the DFI SLI Infinity board- seems to be a decent board, but not many people are running it, so tweak guides are nonexistant. Wasnt really the best time to buy a mobo with the Xpert and ATI boards coming out, but I figured I would give it a try.
Cooling is a Swiftech Storm, MCP650, etc.
When I first got everything fired up, I could load windows up at 3ghz no problem at 1.50 volts. 3.15ghz Suicide screen was about it. Things looked good and I was sure I could stabilize 3ghz.
Unfortunately, this has been a challenge for the last day. As it stands now, I can only get 32m SPi to complete at 2850. For good water cooling, this is somewhat disapoining for me.
As mentioned, I am on a whole new setup here so there may be some kinks I need to work out. The Infinity board is stable at 320 htt when tested with a 8x multi, so I know its not chipset limited per se. I am running OCZ 3700EB (remember these? :D ) and they are good for about 255 3-2-2-10. This would be great at 3ghz, as using a divider runs them at 250 which would be perfect. Unfortunately, cant get the damn thing stable at 3ghz.
In a fit of drunken rage last night, I kicked it up to 1.675v and it primed for about 30min at 3ghz, but 32SPi still fails rather quickly. I would rather not run these volts 24/7 either.
A big problem with the Infinity right now is there is no Smartguardian app that monitors temps properly, so I am left feeling various parts of my cooling loop for a relative measure. It seems to be running quite a bit cooler than my mobile claw, which is puzzling.
--Along the lines of temps... my flow rate really took a dive when going to the storm and the new Swiftech GPU block. Water stays in the raddy longer now, which may lead to the loop being "cooler", but actual heat removal from the die may not be as good. Any one with a Storm care to chime in here?
Now as stated, the DFI 939 is a new platform for me. Many of the bios settings are the same as the Lanparty (I am using newest 8/31 bios). Does anyone have 2 or 3 BIG "everyone knows these" type tweaks for the DFI that I could try? The threads on the Lanparty boards are HUGE and I'm sure someone could save me some time. Thanks in advance.
Yeah- I am kinda disapointed.. I thought about poping the lid off, but as stated, Im not sure temps are really my problem at this point. Plus, I have a 146 coming sometime in the future that I want to try before I start chopping chips up.
Thoughts? Comments?
:toast:
That mb is junk. I got one to try(think it might be a cheap oc'er) and it died on me in less then a day. Sent it back to Newegg for full refund. I then bought a Asrock sata2 and it is a hard mb to oc(except for the master, misteroadster). I am going to wait until the new mb's come out to buy another. LD, there is no comparison between the board you got and a dfi ultra-D or sli.
I don't trust the mb reviews anymore. Alot of the mb's run 2T or won't go much over 250 on memory.
Another bad thing about the mb you have is there are less then half the memory options compared to a ultra ro sli. Rma it and get something else.
try benching with DQS Skew Mode setting = FASTER (or Descreased something in bios) and DQS Skew = 96................it should give you extra points....something eva2000 came across the other dayQuote:
Originally Posted by gundamit
Lex, I have the exact same chip 148 0528 CABYEGPMW. Mine is setting on 2.9ghz 24hour prime stable, 32m SuperPI no problem. Running 1.6v through it.
I am on water also. I did drop 17*c when I took the lid off mine, just did it last night. 17 temp drop is huge. Was running 60-61*c load with CPUBURN. Now it loads at 43-44*c. Haven't tried going past 2.9 yet, letting the chip settle in so to speak.
Is there no way to check your temps? What about Systool or Speedfan?
Concerning your Storm block, it is multitudes more restrictive than a maze3, but also the best comercial block you can buy. Although your flow did decrease I'm sure temps are far better.
Cathar won't like me saying this but you will have to try and reseat the block at it's finnicky.......eva2000 did 19xmounts to get his FX57 right........Quote:
Originally Posted by Plywood99
Quote:
Originally Posted by dinos22
Hmmm. Well its not exactly a evap head or anything... Farirly large heatspreader matched with large ridge on waterblock... tightened the set springs equally a bit at a time... not too sure if contact is a problem. I dont think I would have been able to run 1.7v at 3ghz without a :explode: , but I will check it out. THanks for sugestion.
Wow, that is huge. Maybe the CABYEs have bad heatspreader contact that was just overcome by the brute power of phase by a few people?Quote:
Originally Posted by Plywood99
I still dont think temps are my problem... I am more inclined to believe my board is a POS, but still unsure at this point. Still hoping someone has some DFI tweaks I can try.
Quote:
Originally Posted by gundamit
Stepping /week?!?!
gundamit is running a CABYE 0528 in that screenshot (on phase)
Lex, on the flip side of my IHS, it looked like the tim joint was very thick, thicker than on my clawhammer and my winnie, don't know why there would be a difference but there is. If you want I can throw up a pic for you...
I have the same stepping 146 and with a TT BT it will run about 48c under full load. The optys I have all started out very hot and with some stressing and the AS5 settling in, they all run between 43-48c under load.
The problem is you only have half the memory settings in the mb you have and SG is about half. The ultra-d is the same price as the infinity with alot more options.
If I had a proven mobo that I already knew the limits of and a way to get accurate temps, the HS on my optie would have been a keychain already. Unfortunately, I dont want to be too hasty with that when I dont really know where to source of my problem lies....
Plywood- if its not too much trouble, it would be interesting... I think I know what you are saying about the thick TIM, but pop a pic up so I can check it out.
Here is a pic of the underside of my opty 148 ihs.
The tim looks very thick. The scratch in the middle was made with my fingernail.
But then again I never took the ihs off a cpu before using it for some time. Maybe the stuff goes through phase changes and thins out, I don't know. But a 17*c drop is huge in my book.
On a side note the ihs has the S stamp on it that OPB was talking about. Anyone know what that is? It is on my 3500 Clawhammer ihs also.
http://xs50.xs.to/pics/05410/TimJoint.jpg
Memory set-up always seem to be the thing holding me up. (I'm just getting started on my Patriots again and they're reminding me how sensitive they are to voltage.) Eliminate your stick as the OC party crashers by running your system 274x11 with the 3:4 (150) divider which should take the sticks down to PC3200 speeds. If you still have a problem with 32M stability, try one stick at a time.Quote:
Originally Posted by LexDiamonds
What kind of PSU are you running? If you have a spare you can run jumped use it to power your pump and any fans to decrease the load on the PSU feeding your components. If it stabilizes your OC you might want to look for a better PSU.
Quote:
Originally Posted by gundamit
Yeah, Ive already eliminated my DDR sticks as the problem. I know from previous experience where they are stable at and have always ran them under this limit thusfar. In hindsight, I was actually hoping to maybe push them a little further with the benefits of the improved mem controller and dual channel as my allies.
I have a OCZ 600, so I know my PS is not slacking on the job. I have my 3.3 pot set to about 3.4 to provide the full 3.2 via bios to my EB sticks.
Thanks for sugestions......
Is this tweak specific to Winbond BH/CH type memory? In any case, when I get back to 3D benching I'll give it a try. Perc is sending me some more seal string so I can swap in my 146 next week. Until then I'm working on my water blocks for the video cards.Quote:
Originally Posted by dinos22
looks like the 148 CABYE isn't too bad either......I'll be happy to get prime stable at 3.30Ghz for 24/7 :D :D
Gundamit, did you removed the IHS or is it still on?
i think he had a 2GB kit of something and probably TCCD can't remember last time he used BH5Quote:
Originally Posted by gundamit
I would go for Mushkin Redlines XP4000 :woot:Quote:
Originally Posted by Sinnerman49
Still on. It might not make contact with the evap head and if I remove IHS. Also I might end up selling it - some buyers might not like it already removed.Quote:
Originally Posted by ben805
i think my 1M time was slightly faster too with this setting
http://img437.imageshack.us/img437/2...e27641s4zj.jpg
That's a pretty good time there d22. Is that on wc?Quote:
Originally Posted by dinos22
That TIM job does kind of suck. It looks like it maybe had some air pockets unless those voids were left on the core.
As for the infinity tweaks I don't have an infinity or an opti but I'm thinking you might be able to do all the mem tweaks with a64 tweaker.
If the special vids on that board are available you should print the voltage table from the guide and try different variants since some vids of equivalent voltage are more stable than others.
http://www.dfi-street.com/forum/showthread.php?t=20823
Systool and speedfan works on some gigabytes which also have the IT8712F which is supposed to be whats on the infinity. http://www.dfi-street.com/forum/atta...achmentid=2477
Not to get OT but post how it goes as I'm curious if the infinity can be made to work more or less as well as the lanparty.
I put a 146 in an old neo2 rig they use in the house. When your used to a dfi with all the memory tweaks and then you only have the basic 4, it really makes a big difference in how much of a stable oc you can get. I didn't want to mess around with the TT BT or the hyper6 so I put a smartcat fan on an old silent boost cooler. If I remember right, the MSI core center did not read temps right. It shows 52c idle but I can feel all around it and it doesn't feel hot at all. Anyway, here's a ss with zero memory tweaks (that's why the time stinks). I could run windows at 3000 1:1 but pi wouldn't finish.
Just realised I had ram on 2t.
http://img426.imageshack.us/img426/9...0neo3kd.th.jpg
I've had both boards and the lanparty is a lot better board for the same price. Why would you want to pay the same money and then have to use a bunch of software to try to get where the other mb is already? :confused: You also get all the round cables with the ultra, infinity only has 1 ribbon and floppy ribbon. Smart guard is less and all bio options including dividers are less. Dividers and memory setting are the most important on a 64.Quote:
Originally Posted by gbomb944
It's easy to be curious if something can be made to work if your not the one trying to make it work. :slap:
thanks....yeah i'm on water................BUT I have some problems with 32M times.........not as bad as AFI but certainly pissing me off.............has anyone else compared their 32M times against their old SD or Venice figures hereQuote:
Originally Posted by dogsx2
1M times are unbelievably fast BUT 8M and 32M times are :banana::banana::banana::banana:house..........
Abit AN8 Ultra with Venice at 2.9Ghz RAM on 263MHz 2.5-3-3-6 (GSkill TCCD)
32M SuperPI 25m 50sec
http://img364.imageshack.us/img364/9...pigskillle.jpg
DFI SLI-D with Opteron at 2.9Ghz RAM on 290MHz 2.5-4-3-7 (GSkill TCCD)
32M SuperPI 26m 00sec
http://img414.imageshack.us/img414/9...zdivider6h.jpg
Here is the first Opteron 175 with some OCing action from a fellow OCAU member
Quote:
Originally Posted by Mezmerize
Quote:
Originally Posted by Mezmerize
Quote:
Originally Posted by Mezmerize
I know how bad it sucks to try to make stuff work, which is why I offered what I did, but I didn't tell him to buy it so he could be my guinea pig. :stick: He already bought it and I just offered him some ideas on how to do stuff that he asked for.Quote:
It's easy to be curious if something can be made to work if your not the one trying to make it work
Not sure about a "bunch of software" either since everybody loads a64tweaker and the only difference between smartguardian and speedfan or systool is it doesn't come on the cd in the box. Even guys with ut's have to use a custom config to make mbm5 work. Who oc's that doesn't have to load 8 million bechmarks and tweak tools anyway?
There's also about $50 difference between an sli-dr and an sli infinity so they're not the same price. The ultras are the same but then you have to mod the board which is probably better but I've never modded one and I hear they are putting epoxy over the parts you have to connect now to make it harder. Also nvidia is trying to make drivers to fork up the modded boards so if they pull it off the cheap sli goes down the drain.
If he can't use the vid's then that would kind of suck but if he can get his mem with a64tweaker I don't see how he's hurt too bad.
Got my 148 CABNE 0528 the other day and I'm still playing around with it but I got this so far.
http://img426.imageshack.us/img426/9770/test0bx.jpg
Awesome. Where did you buy it ?Quote:
Originally Posted by DragonFire
:woot:
here is some more OCing by that Opteron 175..........it's looking good
Quote:
Originally Posted by Mezmerize
What kind of aircooling is he using??
TT Big TyphoonQuote:
Originally Posted by Vapor
anybody heard of this stepping ?
CABYE 0535 XPMW
If so tell me some results :)
Somewhere between CABGEs and CAGNEs
0536 cabye cpgw
what about that?
Isn't there a list of OC result with stepping of Opterrons s939 CPU's ?
No. There are general rules of thumb though: CABGE < CABYE < CABNE. We don't have enough data to make any other statements though.
Dinos22, do you know what the markings/week on that 175 are?
CABGE SUX yaaaaaaaaaaaahhhhh :slapass:Quote:
Originally Posted by Vapor
I'll answer since he's probably gone to bed...it's a CCBWE 0534SPMW.Quote:
Originally Posted by Martin Cracauer
( http://forums.overclockers.com.au/sh...41#post5111241 if anyone else from OCAU wants to verify)
While I'm waiting for some more seal string I decided to start playing around with the Asrock 939Dual I picked up for $70 from Ewiz. There are a few threads showing this mobo has some potential with a couple volt mods. I thought it might be a good match for the Opteron because they're both cheap and the Opty doesn't really require much voltage. Without a volt mod, the mobo only gives 1.45v.
Dogsx2 also got this budget board and pm'ed me that he was less than pleased with it. After reading a bit more I decided to start by flashing it to a OCWB beta bios #1 that I picked up here.
Like the EVGA mobo I tested, this bios doesn't include a lot of tweaks, but it remembers its bios settings when OC'ing unlike the EVGA. No Clockgen exists AFAIK for this ULI chipset so it had better. :)
Right now HTT seems limited enough that I'm kicking myself for choosing the 144 (while my 146 just sits) to have first crack at this board. The bios started acting a bit strange around 326HTT so this 144 isn't going to see the same 3ghz it saw on the DFI. I picked out some Twinmos CH UTT and threw a big divider at it. Vdimm selections include "normal" and "high" People with Winbond based memory may want to take a serious look at the vdimm mod.
So here's my start point with this mobo.
http://img215.imageshack.us/img215/1246/312x97mr.png
At PC3200 speed maintaining 1T doesn't seem to be a problem, although that been a problem reported by some with this board and I expect it'll rear its head soon.
I have no idea how far this board will get. How much should you expect for $70? A mildly OC'ed (1ghz :) ) stable game platform wouldn't be too much to ask for right?
uh, i know this may not be right, but im posting it here anyways. since my 146 is on its way, i wanted to just get a record of my outgoing OC. i ran this computer pre WC at 2.5 all year till sept. this is where im at now. at the very least i could learn some things about my mem tweaking, even tho without active cooling it seems 2.6v is my usable voltage limit.
http://valid.x86-secret.com/show_oc?id=43861
this screenshot taken after the 32m completion in superPi