tried higher vcore for 2700mhz.. seems a bit low to me :)
Printable View
tried higher vcore for 2700mhz.. seems a bit low to me :)
Its not about low vcore, but too high temps. I have tried to raise vcore up to 1.9V, but it works even worse because temps raise even higher.Quote:
Originally posted by bias_hjorth
tried higher vcore for 2700mhz.. seems a bit low to me :)
you sure the evap head isnt bended or non flat or what have you?...havent heard of that bad contact between heatspreader and cpu.. :)
Evap temps are good (too good :rolleyes: ) and contact between evaporator and heatspreader is perfect. Because chip overclocks so well with stock cooling, I cant really believe that contact between heatspreader and core is bad :(Quote:
Originally posted by bias_hjorth
you sure the evap head isnt bended or non flat or what have you?...havent heard of that bad contact between heatspreader and cpu.. :)
Dunno whats wrong with it, but I selling the chip away and getting a prescott instead :D
I'm testing my AN50R with a K8NNXP 940 bios
@bias_hjorth
your german ist ok the first sentences was right
hmm ok i think about this to change it r134 out and r404 in !!
but thanks for your answer
willkommen.. :D
I'll be interested to see what comes of this :)Quote:
Originally posted by cpulloverclock
I'm testing my AN50R with a K8NNXP 940 bios
What gains are you expecting?
Did you have to do anything special to get this Gigabyte BIOS to work with the AN50R?
Up to 2.55 SuperPI and 3dmark stable :D
2.6 gives me a round error in SuperPI which means more volts right? Gona Vmod this weekend hopefully :)
Cooling=stock HS with SF2
Good luck, you crazy dude :DQuote:
Originally posted by cpulloverclock
thx :)
I want more
no gain, a bios K8NHA+ is bestQuote:
Originally posted by CodeRed
I'll be interested to see what comes of this :)
What gains are you expecting?
Did you have to do anything special to get this Gigabyte BIOS to work with the AN50R?
awdflash ****.bin /f = reprogram the boot block /cc = clear cmos
You're using a Biostar BIOS on the AN50R? That's nuts. Interesting, though... what made you think to do that? What kind of cross-board problems are there? Any advantages?
Just to let you guys know.. NEVER Buy a A64 2800+.. Have had 2 of them and neither lasted an hour before Dying..
First one lasted 1 hour Then would not Post.. Some slight Overclocking...
The second one lasted 15 Minutes and was at Stock the whole time :eek:
At that point I would be looking for a new mobo or psu or something else.Quote:
Originally posted by hag6br
Just to let you guys know.. NEVER Buy a A64 2800+.. Have had 2 of them and neither lasted an hour before Dying..
First one lasted 1 hour Then would not Post.. Some slight Overclocking...
The second one lasted 15 Minutes and was at Stock the whole time :eek:
Nope.. My 3200+ has been through Hell and Back and still keeps running.. That includes a Vcore as High as 2V and Vdimm as high as 4V and it still runs great... BTW, the Mobo is a Shuttle AN50R..Quote:
Originally posted by Nyge
At that point I would be looking for a new mobo or psu or something else.
The 2800+ 's just did not make it..
http://cal930.hp.infoseek.co.jp/AN50R10428S.png
CLOCK:3019.52MHz@(274.50MHz x11j
CPU: Athlon64 3400+ CAATC 0406RPMW
CPUCOOLING: “º“’“Û‚ÝiDRYICE+ƒƒ^ƒm[ƒ‹jiroom temp16Žj
Vcore: 1.80V
Vddr: 3.43V
Vio: 3.40V
M/B: Shuttle@AN50R:moding(Rev1.3)
bios:K8NHA Pro 0319
Power suplly: AOPEN FSP530-60GN
Memory: TWINMOS BH-5 2462D 256MB
Memoryseting: AUTO LDT~1 CL2.5@8-12-2-2-5-2-2-‚P-2 1~2064
HDD: Maxtor 6Y080P0
OS: Windows win2003
Hi!
BIOS of K8NHA Pro was put into AN50R. a result -- 3019MHz -- superpi -- 28s -- it was able to obtain . However, K8NHA Pro can obtain 28s by 2970MHz.
Sick.. WC with a a64 right?
great to sick the japanese join the sickness.. Now is gonna be whicked :)
congrats :toast:Quote:
Originally posted by CAL930
http://cal930.hp.infoseek.co.jp/AN50R10428S.png
CLOCK:3019.52MHz@(274.50MHz x11j
CPU: Athlon64 3400+ CAATC 0406RPMW
CPUCOOLING: “º“’“Û‚ÝiDRYICE+ƒƒ^ƒm[ƒ‹jiroom temp16Žj
Vcore: 1.80V
Vddr: 3.43V
Vio: 3.40V
M/B: Shuttle@AN50R:moding(Rev1.3)
bios:K8NHA Pro 0319
Power suplly: AOPEN FSP530-60GN
Memory: TWINMOS BH-5 2462D 256MB
Memoryseting: AUTO LDT~1 CL2.5@8-12-2-2-5-2-2-‚P-2 1~2064
HDD: Maxtor 6Y080P0
OS: Windows win2003
Hi!
BIOS of K8NHA Pro was put into AN50R. a result -- 3019MHz -- superpi -- 28s -- it was able to obtain . However, K8NHA Pro can obtain 28s by 2970MHz.
I get 37s at 2190MHz with a K8NHA PRO bios for my shuttle
I had 2 K8NHA PRO and both are dead...
by newbeetle with his Biostar :
http://219.113.251.125/c-board/file/...3D27S%2BWS.gif
and U with a K8NHA PRo :
http://cal930.hp.infoseek.co.jp/28s.jpg
Here's my A64 @ 2.56GHz with 1.7v on AIR @ 39c. I need to rebench because I'm on water now and as soon as I get my 226W TEC I'll see what I can get out of it.
That's nice clocks on air. Can you tell me the stepping of the cpu? I'm looking for a new oc-beast (again), to put under phase-channge. That would be my third A64. :)Quote:
Originally posted by GAMER512
Here's my A64 @ 2.56GHz with 1.7v on AIR @ 39c. I need to rebench because I'm on water now and as soon as I get my 226W TEC I'll see what I can get out of it.
Max clock (unbenchable)
http://users.bigpond.net.au/fxr91/bench/maxclock.jpg
Vapo LS (unmodded), AN50-R (vmodded), vdimm @3.6, vcore 1.95
This is using OCZ PC3500EB 256MB (2.5-4-4-8)
Max 1:1 is 270HTT (unstable) :)
Going to be doing more testing later to see just where I can get to :)
I heard that A64 3200+ CG are the best overclockers...
Is that true? :stick: if so, what is the full stepping of these CPU's?
Another question: what is the differnce between a 3200+ CG and a 3200+ C0?
and what is a DTR chip?
thanks.
A DTR is a "DeskTop Replacement" chip. It is an A64 with the IHS removed, meaning you have to do some modifying of your cooling solution to touch the core as it sits lower than the IHS.
From what I know, the only real difference between the C0 and the CG stepping of cpu's is that the memory compatability was improved with the CG.
Great, thanks!Quote:
Originally posted by fxr91
From what I know, the only real difference between the C0 and the CG stepping of cpu's is that the memory compatability was improved with the CG.
I heard also that there is A difference between the chache (512Kb/1Mb) and the multi (11x/10x), is that true?
Oh, and what about overclocking capabilities?
(This is for personal knowledge only, im very satisfied with my chip ;)).
Still tweaking.
Stabil at 3340-3360 now.
Schreenshot::D
sweet stuff dudes.
macci's benching live if anyone is interested.
http://www.muropaketti.com/webcam/
there is a thread in the 3d forum and at planetmars
I got an A64 3400+
it never even got hot to 225 FSB when the mobo crapped out.
:toast:Quote:
Originally posted by Tom Holck
Still tweaking.
Stabil at 3340-3360 now.
Schreenshot::D
I see you are still overclocking them FX's :slobber:
:slobber: That is great Tom! I'm seeing foward to see some benches, when you get your X800Pro/XT :banana:Quote:
Originally posted by Tom Holck
Still tweaking.
Stabil at 3340-3360 now.
Schreenshot::D
CPULL
where are the mods for the biostar?
damn nice all of you!
Yeah my stepping is CAAOC 0352 XPMW and I've had another 3000+ with the same stepping that did 2.55GHz with 1.7v on AIR.Quote:
Originally posted by Nyge
That's nice clocks on air. Can you tell me the stepping of the cpu? I'm looking for a new oc-beast (again), to put under phase-channge. That would be my third A64. :)
If I got an option to choose single 3200+, which one should i go for to give the best clocks?
CG ClawHammer
CG NewCastel
C0 ClawHammer
C0 NewCastel
Again, i want this best clocker!
(tell me the week also)
I would choose for this one :Quote:
Originally posted by Primal
If I got an option to choose single 3200+, which one should i go for to give the best clocks?
CG ClawHammer
CG NewCastel
C0 ClawHammer
C0 NewCastel
Again, i want this best clocker!
(tell me the week also)
CG NewCastle
Am looking for one myself, because it has got the real juicy MP 11 :banana: :toast:
It also got improved memory compatebility wich is very nice when it comes to BH-5 in 512 MB sticks !!!
It also preforms a bit better at default than its clawhammer 1 MB brother.
When it comes to week dates always choose the most recent !!
Great man, thanks for the help! :banana:
Should I go for green or brown chip?
you know what is the full stepping of NewCastle CG?
Oh, and what about overclocking capabilities compared to ClawHammers C0/CG?
thanks :toast:
The color doenst realy matter.Quote:
Originally posted by Primal
Great man, thanks for the help! :banana:
Should I go for green or brown chip?
you know what is the full stepping of NewCastle CG?
Oh, and what about overclocking capabilities compared to ClawHammers C0/CG?
thanks :toast:
You can recognice a typical core as stated below :
Athlon64 3400+ 2200MHz 1MB ADA3400AEP5AR (CG)
Athlon64 3400+ 2200MHz 1MB ADA3400AEP5AP (C0)
Athlon64 3200+ 2200MHz 512KB ADA3200AEP4AX (CG)
Athlon64 3200+ 2000MHz 1MB ADA3200AEP5AR (CG)
Athlon64 3200+ 2000MHz 1MB ADA3200AEP5AP (C0)
Athlon64 3000+ 2000MHz 512KB ADA3000AEP4AX (CG)
Athlon64 3000+ 2000MHz 512KB ADA3000AEP4AR (CG)
Athlon64 3000+ 2000MHz 512KB ADA3000AEP4AP (C0)
Athlon64 2800+ 1800MHz 512KB ADA2800AEP4AX (CG
Any CPU that is NewCastle core must be CG right?
But there are CG's that are ClawHammer right?
Yep thats true the 3000+ CG is easy to recognice but with the 3200+ you must look for the 2.2 Ghz (512 Kb Cache) version.Quote:
Originally posted by Primal
Any CPU that is NewCastle core must be CG right?
But there are CG's that are ClawHammer right?
If i'll find this version OCing is guaranteed no matter the week, batch etc. (Sure i'll try to find the newest week, and best batch)?
Again, you sure PCB color doesn't matter?
http://www.xtremesystems.org/forums/...threadid=35186 :stick:Quote:
Originally posted by SmokeyTheBandit
It also preforms a bit better at default than its clawhammer 1 MB brother.
As you can see in 90 % of the normal daily used appz it is a bit faster.Quote:
Sure 3D Mark/Pifast gives a bit higher scores but im more interesed in the encoding of DVDs for example and gaming etc. and i know that in these cases Mhz is more effective than cache.
The change of getting higher clocks with the Newcastle 3200+ is much bigger.
Ill bet a 2800Mhz Clawhammer is slower than an 3000 Mhz Newcastle ;)
But this is something we have to encounter ourselfs in the next few weeks.
I hope i get my 3200+ newcastle tommorrow together with my brand new and modded EPoX 8KDA3+ :D:D
Interesting, I didn't see any compairisons for encoding. If you have a link for that it would be great. I would also think that most games would follow 2001se, which clock for clock you lose 700 points and it takes the extra 200mhz to draw almost even. from what I've seen you'd have to overclock to around 200mhz higher with the NC. Meaning your 2.85 NC would be on par with a 2.65-2.7 CL. If you have some encoding test and stuff it might be interesting to see the difference.
I will look for a couple of screenies with encoding differences.Quote:
Originally posted by pkrew
Interesting, I didn't see any compairisons for encoding. If you have a link for that it would be great. I would also think that most games would follow 2001se, which clock for clock you lose 700 points and it takes the extra 200mhz to draw almost even. from what I've seen you'd have to overclock to around 200mhz higher with the NC. Meaning your 2.85 NC would be on par with a 2.65-2.7 CL. If you have some encoding test and stuff it might be interesting to see the difference.
If you look here at the Pifast link below you see the score of the 3400+ from Z3us and my 3000+
http://www.ministryofoverclocking.ne....php?klasse=10
Z3us 3400+ @ 2.56
SmokeyTheBandit 3000+ @ 2.81
Well if you see the scores than you will see that it isnt on pair with the Newcastle even though it is a 1 MB around 2.6 Ghz.
:banana:
I think a 1 MB version will improve the scores on the same speeds by 1 / 1.5 Sec.
Well, I kinda want A CPU that's overclocks the best when i'll put it under the prommy.
So, the chosen one is 3200+ NewCastle CG or 3200+ ClawHammer CG? (No way i'm going for C0.. compatibility with 512Mb sticks is critical for me).
Thanks, Roy :toast:
its a little slow, but you're about right for pfast. Just for fun lets keep going
YipQuote:
Originally posted by Primal
But there are CG's that are ClawHammer right?
ADA3400AEP5AR
CAAPC 0407SPMW
Anyway, should I got for ClawHammer CG or NewCastle CG?
(I want the best OCer).
freaks !!!!!
Well i ordered an new chip :D:D
Athlon 64 3200+ Newcastle - AX - 0414 - XPMW :banana:
I hope this will finally let me break the 3 ghz stable barrier :D :P
This should go nicly on my new EPoX 8KDA3+ (nForce 3 250 GB).
Will let you guys know what its capable of :)
:toast:
Can't wait for the results, if it's good i'll buy it too :toast:Quote:
Originally posted by SmokeyTheBandit
Well i ordered an new chip :D:D
Athlon 64 3200+ Newcastle - AX - 0414 - XPMW :banana:
I hope this will finally let me break the 3 ghz stable barrier :D :P
This should go nicly on my new EPoX 8KDA3+ (nForce 3 250 GB).
Will let you guys know what its capable of :)
:toast:
Anyway, it's that NewCastle with 2.2Ghz & 512k chace?
A very short answer : YES :banana: :toast:Quote:
Originally posted by Primal
Can't wait for the results, if it's good i'll buy it too :toast:
Anyway, it's that NewCastle with 2.2Ghz & 512k chace?
Cool!Quote:
Originally posted by SmokeyTheBandit
A very short answer : YES :banana: :toast:
Already saw you updated your sig...
Yep im looking for vmods for the EPoX 8KDA3+ because i want to put them on before i put this motherboard + cpu under the prom :rolleyes:Quote:
Originally posted by Primal
Cool!
Already saw you updated your sig...
Why did you choose the EPoX upon GigaByte, Chaintech and more..?
Because this is the only one thats available here in holland besides the Chaintech.Quote:
Originally posted by Primal
Why did you choose the EPoX upon GigaByte, Chaintech and more..?
The Chaintech 250 preforms the same as his 150 brother , that is unacceptable offcourse (new chipset = beter preformace).
And the EPoX has 6 S-ATA controllers onboard wich i use so thats a must for me.
The other brands have not arrived here and will not arrive in a few weeks if you ask me.
I think that i will order my new Abit KV8 Pro tomorrow :p:
I'm gonna post some results in here when Abit has released the new BIOS ;)
Check this out:
http://www.anandtech.com/chipsets/showdoc.html?i=2063
Great review, I recommend it, very useful for people who wants to buy an A64+2nd mobo's at these days...
By the way, the Epox 8KDA3+ is the winner :banana:
It overclock the best, preforms extremely well and has a great variety of features. thought i'd go for the K8NS, but no... :rotf:
NF3250Gb rocks!
The Epox, oc's just as much as the Abit, 2480MHz... And the Abit has vcore up to 1.8v and vdimm 3.2 in ocguru, so i would pick the Abit, IF they soon release a new bios with agp/pci lock fix.
The MSI K8N Neo plat. looks nice too :) vcore op to 1.81v but only vdimm 2.85v
looks okay but nothing to change your excisting nf3 150 mobo over IMO :)
Well... I will change it with the Abit, but only if I know that there is'nt any problems with the agp/pci lock and multiplier-selection etc. :rolleyes:Quote:
Originally posted by bias_hjorth
looks okay but nothing to change your excisting nf3 150 mobo over IMO :)
If you read more carefully, you´ll se Abit have already fixed the agp/pci lock. All shipping boards will have working agp/pci lock.Quote:
Originally posted by K32A
The Epox, oc's just as much as the Abit, 2480MHz... And the Abit has vcore up to 1.8v and vdimm 3.2 in ocguru, so i would pick the Abit, IF they soon release a new bios with agp/pci lock fix.
The MSI K8N Neo plat. looks nice too :) vcore op to 1.81v but only vdimm 2.85v
Im acually going to give the K8V Pro a try tho its Via chipset.
Formann...
oops, my mistake.
But the Abit still have some probs. with the multiplier selection, and it also boots up with x9 multi on x10 cpu's... That what the test says
Agreed. My K8NPRO will do 350 FSB (Raid 0) and that`s good enough for me. Only thing missing is hardware firewall and I could care less.Quote:
Originally posted by bias_hjorth
looks okay but nothing to change your excisting nf3 150 mobo over IMO :)
1.8vcore with water, is that too much?
No it ain't. I have had 1.9V for several weeks now.Quote:
Originally posted by K32A
1.8vcore with water, is that too much?
Thx ;)
hello :banana:
Does core revsion AX (DH7-CG like 939) on sock 754 have a better overcloking results ?
does it have a probleme with 512 bh5 sticks and core Co ?
thanks
http://home.quicknet.nl/qn/prive/pjm...ifast43.81.JPGQuote:
Originally posted by damsxx
hello :banana:
Does core revsion AX (DH7-CG like 939) on sock 754 have a better overcloking results ?
does it have a probleme with 512 bh5 sticks and core Co ?
thanks
This is done with 2x 512 MB BH-5 Stix and a 3200+ NC AX Core ;)
So yeah its much better :D
Smokey, after I saw your OCing results I think i'm ready to buy 3200+ NewCastle! :banana: Awesome results man, congrats!
Oh and what's limiting you on the way to the 3Ghz club?
How much Vcore & Vdimm? & Dividers? Thanks...
i'll think i'll get NC 3200+/EP-8KDA3+/OCZ EB/X800Pro next week... :toast:
Heej im figuring out this mobo , its got some bios issues wich have to be solved before i can take full advantage of this awesome motherboard.Quote:
Originally posted by Primal
Smokey, after I saw your OCing results I think i'm ready to buy 3200+ NewCastle! :banana: Awesome results man, congrats!
Oh and what's limiting you on the way to the 3Ghz club?
How much Vcore & Vdimm? & Dividers? Thanks...
i'll think i'll get NC 3200+/EP-8KDA3+/OCZ EB/X800Pro next week... :toast:
An example is that it runs much much more stable with 2x 512 mb dimms in stead of 1 wich is very strange :stick: .
I cannot run 10x 290 + with 1x 512 MB dimm but only with 2.
Another example is the Dimm + Core voltages wich arent very stable with or without the Vcore or VDimm mod.
A new result :D ;)
http://home.quicknet.nl/qn/prive/pjm...ifast43.58.JPG
Vcore @1.9 V
Vdimm @ 3.32 V
This is done with my brand new Enermax 550 Watt PSU ( 36A @ 12V :toast: :slobber: )
Just got my 3200+ (0411) and a Chaintech nForce3 znf 250
I've got some Corsair pc4000 Xms, MachI and Zalman NB47J for the NB.
Rigth now it is stable at 2600mhz, but anything over that is unstabil.
What can I expect to hit whit a Vmod?
Btw Friday i will get a a64 3200+(caamc o344) anyone knows something about that stepping?
sorry for my english
caamc is a good old stepping.. I have a similar.. although 2600mhz seems a tad too low.. what vcore etc are ya running?... btw. those xms4000 really kills your performance..
bias_hjorth:
Vcore 1.7 max for my mobo, Vmod should do the work, what you mean when you say that xms4000 will kill my performance?
high latency and high mhz is not the best combination :)
Well, I don't think these minor probs will prevent me from buying this great board... :DQuote:
Originally posted by SmokeyTheBandit
Heej im figuring out this mobo , its got some bios issues wich have to be solved before i can take full advantage of this awesome motherboard.
An example is that it runs much much more stable with 2x 512 mb dimms in stead of 1 wich is very strange :stick: .
I cannot run 10x 290 + with 1x 512 MB dimm but only with 2.
Another example is the Dimm + Core voltages wich arent very stable with or without the Vcore or VDimm mod.
A new result :D
*IMG*
Vcore @1.9 V
Vdimm @ 3.32 V
This is done with my brand new Enermax 550 Watt PSU ( 36A @ 12V :toast: :slobber: )
By the way this week im getting Forton 530W or PC P&C 510 ATX-Deluxe !! :banana: should handle my a64 very well...... :D
Anybody have a 3200+ @ 1.9V being watercooled?
been there on air with a 0352 3000+
my a64 3000(clawhammer) maxed out at 2354 mhz on stock air, no vmods on a k8n pro. Is this good or bad? It is a CAATC stepping.
Hello
My A64 3200+ (CAAMC 0341WPMW) is doing 2338 MHz at 1,68 V which ist the max. voltage my Board provides.
greetz
Hotspot
PS: Runs with watercooling 39°C under load.
yeah! i have an a64 3200 caamc on shuttle an50r with 1,92 vcore it runs stable at 2530mhz ,and the temps are 46-56 cooled by asetek watercooling .i will try a vapo this month :d
WOW!!!!:confused: 46-56C on watercool thats really high, but then again I havent heard great things about those asetek waterblocks, what kind of rad/fan configuration do you have?
i use the large rad with 2x120 fan and ls30 pump but this temps i get when i clock to 2530mhz at 1,92v!!
are you sure you need 1.92 to reach 2530.. I believe thats a tad below standard for the a64 3000 cpu :)
What kind of 120mm fans are you using? Stealths...lol:confused:
Does your board offer a chipset vmod? I think that is what is holding you back.
I think that you should remount your waterblock. I think that bad contact is holding you backQuote:
Originally posted by ogica
i use the large rad with 2x120 fan and ls30 pump but this temps i get when i clock to 2530mhz at 1,92v!!
I'm running a watercooled A64 and the stressed temp is 36g with a roomtemp of 30g (watertemp is also 30g)
Full setup: Airplex EVO360 with 2x120mm Papst @ 1500rpm, Swiftech MCW5000-64 (also not a very high-end block)
A64 3200+ 1MB @ 2400MHz 1,8v (normally a hotter chip than yours ;) )
I don't think that my temps will rise that much when I give my chip another 0,2v
Btw, max oc of my cpu:
http://www.voidyourwarranty.nl/image...en/46.77rs.JPG
http://www.voidyourwarranty.nl/image...chen/46.77.JPG
Running @ chilled water of 5g
i will try with an antartica head next week :d
also at 1.968v how cold is your cpu ?
At that moment of benching it was about 25 degrees full stressed.Quote:
Originally posted by ogica
i will try with an antartica head next week :d
also at 1.968v how cold is your cpu ?
I tested specially for you the temps with more normal watertemps, and after 5 minuts of prime95 (small blocks) my cpu was 43g full stressed. Watertemp at that moment was 27 degrees
I didn't test any longer cause I could actually smell my mosfets burning :eek: (no kidding)
During benching they are cooled by a 120mm fan @ 12v, but when gaming I only cool them with a 80mm @ 5v (no sinks) so they didn't like this test at all :P
screenshots:
http://www.voidyourwarranty.nl/image...emp_testrs.JPG
http://www.voidyourwarranty.nl/image..._temp_test.JPG
i am still waiting for the vapo xe :d
SynGroW Almost 2.0vcore to get 2400MHz :| Thats insane... Have'nt you tried with 1.7vcore or something like that ?
My A64 3200+ Clawhammer will do 2419Mhz stable with 1.68vcore...
LOL, that was only to show what kind of cpu temps I would get @ 2vQuote:
Originally posted by K32A
SynGroW Almost 2.0vcore to get 2400MHz :| Thats insane... Have'nt you tried with 1.7vcore or something like that ?
My A64 3200+ Clawhammer will do 2419Mhz stable with 1.68vcore...
My cpu does 2400MHz totaly stable @ 1,75v
My max is at 2600MHz at about 1,9v
Lol - In a minute a thought u've got the bad'est chip in the world :-D
i want to buy another a64 3200 :d
anyone to want to sell ?:p
a better oc than mine :(
2400 at 1,82 (stable)
I am back at 2500mhz with my new and freshly modded VNF3-250. However I now need more volts to run 2.5 stable. Using the 5:6 memory divider on my AN50R I did 2.5ghz stable @ 1.74v, now at 1:1 I need 1.79v to do it stable. Is this typical?
i want to buy a good oc chip :d maybe to hit 3gh on vapo xe
a64 :d
who hit 2600 on air or over 2600 on water :d
pls who can help me?
:p
browse though this thread.. some did.. :) but 3ghz on a XE.. come on...
A 3ghz 2V A64 is over 210 watts of heat... Can an XE even handle that?
xe can handle 180w.
anyway at least 2700-2800mhz :d i wish a good oc chip :d
my friend has now an a64 3400 wich does 2700 mhz on my asetek water with 1,850 :d i think will rullz :d
My results :
http://koti.mbnet.fi/jiipee75/Epox%2...xSpiM8_5_49.gi
CPU can go higher than that but RAM don´t