Printable View
I got it working but stopped for a couple of back surgeries...will pick back up on it when I have more time. It's fun but not very practical for every day use.Quote:
Originally posted by Tettejaak
Lol, didn't even thought about it :)
offtopic: @theDude: some months ago you were planning to make a direct die wc. How did it end up? :)
Hi All
have my waterchill system up and running, i have a NF7-S mobo with a 2500 barton, have it clocked to 2.6ghz, but want to know what is a safe voltage to keep the core at, that is is the voltage ok up high if the cpu temp is low, present temp is sitting between 41 on ide and 50 working, the system is 218FSB at 12x multiplier, at 2.1v, cant get the FSB above 219, but do have new ram comming OCZ 3700 dual 1Ghz,
Thanks
silentRunner
This happens with my a7n8x too.Quote:
Originally posted by DaGooch
This is very similar to my 166MHz XP2600+ chip on an Epox 8RDA+. I can not run high FSB and will always crash entering windows with the 166FSB jumper on past 190MHz. I take the jumper off and the chip defaults to a XP2000+ and maximum stable FSB of 225MHz with ease.
NF7-s does have this jumper, too?
hum... this is a very interesting thread. im running a 2600(none barton core) 333 chip with an abit nf7's v2 using the orrigional bios that came with the board. (volt modded by mr.zee) and my 2600 with out blowing or cutting any of the L12 bridges hits much above the 200 fsb mark... benchen i usually have my overclock set at. 11x 220ish (depending on how cold my computer is). The only weird the only weird thing with my 2600 is havving is; it has issues some times. meaning. some times im able to run 10.5x 232 (prime for overclocking) but as of lately i can only run at 11x220ish which is weird not to mention makeing me mad because 10.5x232 was prime stable untill i tryed a little more overclock then bomb clear ccmos. and i was never able to get that good of an overclock again. it's ok though hopefully my next rig (an7 2800barton watercooled) will have more luck. GREAT FIND though
id check the posts on the an7 first and wait till they get all theQuote:
Originally posted by thetruememphis
hum... it's ok though hopefully my next rig (an7 2800barton watercooled) will have more luck. GREAT FIND though
problems sorted out first.a lot of the mobos have been hand modified to fix obvious problems.
whussup yall?
i got a Barton 2800+ that can do about 220fsb and then any higher it startz crappin out on me. so i got a question does this L12 mod work on Bartons? or anyone try yet at least? and ive modded a few thingz in my time, but havent modded a cpu before, so just to make shure i got this down: black mark = closed, no black mark = open? or the other way around? thanx much!
oh and i still got a EPoX 8RDA3+ right now, havent gotten my AN7 yet. hopin i get a decent one :-\
Hi Guys, got my machine now running at 215 FSB & 12 on the multipler, can anyone give me some pionters on where to start with the memory timing. Thanks
Welcome to Xtreme dazzal! :D
:toast:
What are your current memory timings? Do you know if that's BH-5 ram? Have you done any voltage mods? Which PSU do you use?
Sorry for all the questions, but this info will help. ;)
Thanks for the welcome.
Here goes then;
Memory 2 x TWINMOS PC3200 512MB DDR400 CL2.5 OEM
CPU core 1.7
DDR SDRAM 2.9
Chipset Voltage 1.7
AGP Voltage 1.6
Memory timings
OPT set row delay 9
RAS to CAS act delay 4
Row precharge delay 4
CAS latency time 9
Power supply Advance CWT-375ATX 375 w
Hope this helps.
Thanks
emmm... if this NF7-S problem is da mater off dat.... Processor ID thing....
nice discovery... will look into it later
cheers:toast:
ok i just modded D22
i disable processor id except i left 3200+ ID only n i disable multi 17,18,19,20,21,22,23,24
yup... it post fine n load to win xp... but dat multi 10 n 10.5 issue still there
so i assume this prob come from nvidia it self... nvidia BPL Bios version
Pics not working, wanna try this mod when i finsih waterchiller.
hey guys,
i've got an A7N8X Rev2, Bios 1007, with Barton 2500 and Crucial PC3200 Ram (2x512).
oh ya, and i have a Prommie Mach 1 chilling to cputemp -3.
i have tried setting jumper to 100 and cpu posts @ 1100 default etc etc, but i still hit the 200mhz fsb wall. i've tried low multipliers slow mem speeds etc etc, and no luck. also, my multiplier tops at 12.5 both ways.
will cutting L12/3 help if jumper is still leaving me @ same place? any suggestions? i'd prefer a higher fsb, but would settle for higher multiplier.
thx
Have a abit NF7-s good board with a 2500 barton, with the L12 bridge cut, i have a water chilled system with a GF4 Ti4600, and OCZ 3700 ddr duel 1ghz, but want a change want a athlon 64 3200 but the inportant question is - what mobo to go with for overclocking any ideas.
not much reponce yet, how ever had a last ditc attempt to see if i could overclock the machine again and keep it stable, the two month burn in must have done it good, 'cause she is sitting at 2.42ghz stable as F*** with is gd for a OC beginner, but it wasn't clean saliling, before the L12 bridge was cut could get the FSB above 215 but when i cut it i am only getting a 222 not much of a difference, but hey. the settings are as follows, so if there are any ideas on how to increase it let me know
FSB 222 at 11x multi
cpu Core V = 2.06v
ddr core v = 2.7
chipset V = 1.7
AGP V = 1.6
CPU running at 2442MHz
Memory timings are
10, 4, 4, 3.0
with is the optimal setting for the abit NF7-s V2 mobo
please help away
i solved my problems discussed at the end of this thread..
http://discuss.futuremark.com/forum/...371833&fpart=3
PS I am username "Potent" on that forum...
removed the sticky, thread will remain here but its time to move on and make room for more recent and actual stickies
Another solution is this RAM:
Patriot PDC1G3200+XBLK 1GB Kit DDR400 PC3200
Mine runs 246 MHz now -- better than my BH-5!