Thanks :)
It properly my old build from two or three months ago... now i have some new parts I will post new pictures soon.
Printable View
Thanks :)
It properly my old build from two or three months ago... now i have some new parts I will post new pictures soon.
Woo, I am feeling that first picture! Nice job! :clap:
http://galeria.shackit.pl/Snow/slide.htmlQuote:
Originally Posted by Dangals
here is full fotolog ;)
@snow: i love your shots mate! :up:
Nice! But let's add some clamps to rev2;)Quote:
Originally Posted by *Snow*
Do you really need clamps?? Snow what dye are you using? Color looks great!
Nice slideshow setup there...are all of those submissions or did you collect them and organize them up?Quote:
Originally Posted by Arni
WOW that is nice
just looking at 7/16 over 1/2 w. no clamps makes me nervous.
is your loop order GPU -> CPU -> SB???? thats a little odd to me, as your gpu is usually a lot less finnicky about higher temps, but i guess if you went cpu first it your tubing runs wouldnt be as clean :shrug:
otherwise, everything looks great!:clap:
Wow great stuff guys, keep it coming! :yepp:
The standard of build and photography has been upped a notch recently if i dare say so. ;)
They better be, i've only got 4 slots total to play with! :eek: :rofl:Quote:
Originally Posted by evil-98
Thanks guys for all good opinion ;)
I dont need any clamps ;) its very hard to set this tygon tube on those swiftech fittings so it can't fly out. Im using Feser One UV Blue and probably in my next rev. I'll need more liquid :DQuote:
Originally Posted by Detale
Rich people.. nice pc *snow*, btw.
......
ive only got 3 :rolleyes: unless i get a ridiculously long PCI extension :rofl:Quote:
Originally Posted by twwen2
I can't see anything O.oQuote:
Originally Posted by ShArKo
I bet your Skulltrail was cheap too. :p: It always depends what you invest your money in, perhaps half the people don't have a house and drive a 1970's model Lada.Quote:
Originally Posted by pcaddict
Good stuff people, especially that homemade case.
dam......wait I will be update the photos again :s :s
Here are the Photos :D:D:D:D
http://img7.pictiger.com/2fa/16731981_th.jpg http://img7.pictiger.com/bc4/16731985_th.jpg
http://img7.pictiger.com/919/16732997_th.jpg http://img7.pictiger.com/452/16733002_th.jpg
http://img7.pictiger.com/4be/16733005_th.jpg http://img7.pictiger.com/511/16733009_th.jpg
http://img7.pictiger.com/2dd/16733015_th.jpg http://img7.pictiger.com/3d8/16733016_th.jpg
http://img7.pictiger.com/be1/16733019_th.jpg http://img7.pictiger.com/844/16733023_th.jpg
http://img7.pictiger.com/d27/16733035_th.jpg http://img7.pictiger.com/c4d/16733071_th.jpg
http://img7.pictiger.com/13e/16733073_th.jpg http://img7.pictiger.com/35f/16733077_th.jpg http://img7.pictiger.com/443/16733079_th.jpg
http://img7.pictiger.com/b4e/16733083_th.jpg http://img7.pictiger.com/6cf/16733085_th.jpg
http://img7.pictiger.com/67a/16733086_th.jpg http://img7.pictiger.com/47c/16733092_th.jpg
http://img7.pictiger.com/dc5/16733098_th.jpg http://img7.pictiger.com/d93/16733101_th.jpg
Please correct me if I'm wrong, but isn't the water temperature almost the same in every part of the loop? Or so I've heard, anyways within 1-2'C temp range regardless the spot of the rad.:shrug:Quote:
Originally Posted by ballzD33P
That wasn't his point, his point was that the GPU will be dumping it's heat directly into the CPU, which is much more finicky about temps. ;)Quote:
Originally Posted by Lagaaja
hi guys ,my old and new system
http://img240.imageshack.us/img240/9646/49680158zi1.jpg
http://img240.imageshack.us/img240/4...pg/1/w1204.png
http://img240.imageshack.us/img240/51/53948479jy1.jpg
http://img240.imageshack.us/img240/5...jpg/1/w480.png
http://img78.imageshack.us/img78/9039/48562587tl1.jpg
http://img78.imageshack.us/img78/485...jpg/1/w640.png
http://i35.tinypic.com/vosw95.jpg
mine,
Ek Supreme, Mcp355, Ekrestop (with self made antycyclon from old ram packaging), Ek 4870 Fullcover block, 3/8 Blue Tubing and a Blackice GTX360 in a Cosmos S. pic was taken with power off, but its not like it would look much different anyway since I dont believe in led's in Computers.
yes, below pic still has bubbles in it, they are gone now dont worry, but looks like pure pr0n in my opinion.
http://i35.tinypic.com/2eef0qv.jpg
Well your pr0n obviously isn't my definition of pr0n but who cares. Nice PCs guys.
How long did your loop take to bleed Naokaji?
My small update;) I exchanged fittings on Bitspower:D
http://images33.fotosik.pl/365/44fee60b01dd93f8.jpg
http://images33.fotosik.pl/365/3ae2defa970e33be.jpg
http://images49.fotosik.pl/10/a18d2c12d53e9057.jpg
http://images41.fotosik.pl/10/eeaf03cc19f643b8.jpg
http://images39.fotosik.pl/10/1041a8344deaf235.jpg
http://images34.fotosik.pl/360/ae2d47b2011393d8.jpg
http://images39.fotosik.pl/10/6d14d00b4d68dafe.jpg
Seba,
what fittings are those?
They look way better than what I planned to use (Bitspower Premium G1/4" High Flow 1/2" Fitting)
EDIT:
Are they this ones? Bitspower Premium G1/4" High Flow 1/2" Compression Fitting (For Tygon 1/2" Tubing)
took a few hours with slow progress, until I tilted the case in various directions which helped a lot getting the air out of the rad within a few minutes, then it wasnt much longer until there was no air left.Quote:
Originally Posted by MomijiTMO
this one http://www.aquatuning.de/product_inf...--knurled.htmlQuote:
Originally Posted by slim142
Seba that looks great. Are those 1/2" ID 3/4" tubes?
I'm really liking the compression fittings.
Quote:
Originally Posted by slim142
Quote:
Originally Posted by seba84_2005
Please somebody confirm this because if you ask me, we linked the same product, just different websites. AM I RIGHT?
same product but different in sizesQuote:
Originally Posted by slim142
he used 3/8x1/2 Bitspower compression fitting (AFAIK)
and you link a 1/2x3/4 Bitspower compression fitting
http://i192.photobucket.com/albums/z...p/2840cdf6.jpg
http://i192.photobucket.com/albums/z...p/914f8525.jpg
I have this:Quote:
Originally Posted by slim142
http://www.frozencpu.com/products/22...n_Fitting.html
you thought about these
http://www.frozencpu.com/products/80...tl=g30c101s178
these do not fit on blocks EK NB & SB
http://img98.imageshack.us/img98/467...omplettru0.jpg
http://img529.imageshack.us/img529/2...closeupxo3.jpg
http://img373.imageshack.us/img373/7...ttseitema8.jpg
http://img49.imageshack.us/img49/764...0cfobensp0.jpg
http://img364.imageshack.us/img364/1...cfuntencg6.jpg
http://img356.imageshack.us/img356/7...tekobennf0.jpg
http://www.gravedigga.de/gravedigga/...preme_oben.jpg
http://www.gravedigga.de/gravedigga/...reme_unten.jpg
Built this, one year ago :) But the it will strangely never be finished :( allways gotta do sumthing with it :p:
http://www.bandwidth.se/thumbs/10225.jpg
http://www.bandwidth.se/thumbs/10224.jpg
I kinda like tygoon, after a year with normal battery water (changed every 3rd month )and that i recently put in green glycol it kinda looks like sewer water :D i allso digg the towel :) used as vibrationdamper cos my ''hdd rack'' wont fit with my 3870x2
mmm loooking good
http://img529.imageshack.us/img529/2...closeupxo3.jpg
Your card is bending a lot near the ram slots. Just like mine. And just like me, you have an EK fullcover block on the hd4870
seba84_2005, what is the fan in the back?
funkflix, Is that stock nb cooler? looks weird.
wow some amazing setups here, I haven't posted in awhile but I just finished mine, I'm too lazy to get it as clean as some on here but oh well
http://img353.imageshack.us/img353/3987/comp1al5.jpg
http://img353.imageshack.us/img353/9963/comp3vp6.jpg
http://img529.imageshack.us/img529/5078/comp2hv5.jpg
http://img353.imageshack.us/img353/8924/comp4bw2.jpg
http://img353.imageshack.us/img353/c...pg/1/w1037.png
this is Noiseblocker BlackSilent XL2 120mm - rev.3 blue led mod:DQuote:
Originally Posted by pcaddict
|Oc|REvO_HsArC sweet-looking setup there!
So for conclusionQuote:
Originally Posted by seba84_2005
Will this 1/2x3/4 Bitspower Compression Fittings fit on a D-tek Fuzion V2, Feser 480, Bitspower BlackFrezer, Swiftech MCP655 pump and a EK Res250?
I was looking around and I found out that 1/2x3/4 are too fat to fit on the Fuzion V2, true?
I believe that is true.Quote:
Originally Posted by slim142
If you find any information, please post in the link in my signature, as we are trying to compile a compatibility list for compression fittings and blocks.
New case, I've bought the Lian-Li PC-A70B because this case will allow me to put 3 rads in :D
I had a Lian-Li PC-71 before this :)
Hope you like it, any questions?
Just ask :up:
PS I used old/broken fans as shrouds, ripped the guts out and then used the "outside", works like a charm :)
heres mine first time i ever watercooled.
yes:(Quote:
Originally Posted by slim142
3/8x1/2 16mm they fit with the small space;)
1/2x3/4 22mm they do not fit on D-Tek v2:shakes:
Finally,my beast:)
http://www.pctunerup.com/up/results/...8_DSC00504.JPGhttp://www.pctunerup.com/up/results/...2_DSC00505.JPG
http://www.pctunerup.com/up/results/...0_DSC00507.JPGhttp://www.pctunerup.com/up/results/...0_DSC00508.JPG
http://www.pctunerup.com/up/results/...5_DSC00510.JPGhttp://www.pctunerup.com/up/results/...9_DSC00513.JPG
http://www.pctunerup.com/up/results/...2_DSC00514.JPGhttp://www.pctunerup.com/up/results/...7_DSC00515.JPG
http://www.pctunerup.com/up/results/...8_DSC00516.JPGhttp://www.pctunerup.com/up/results/...6_DSC00519.JPG
http://www.pctunerup.com/up/results/...1_DSC00522.JPGhttp://www.pctunerup.com/up/results/...8_DSC00523.JPG
http://www.pctunerup.com/up/results/...5_DSC00525.JPGhttp://www.pctunerup.com/up/results/...7_DSC00538.JPG
http://www.pctunerup.com/up/results/...0_DSC00539.JPGhttp://www.pctunerup.com/up/results/...2_DSC00540.JPG
http://www.pctunerup.com/up/results/...7_DSC00541.JPGhttp://www.pctunerup.com/up/results/...0_DSC00542.JPG
http://www.pctunerup.com/up/results/...1_DSC00543.JPGhttp://www.pctunerup.com/up/results/...6_DSC00545.JPG
http://www.pctunerup.com/up/results/...1_DSC00546.JPG
Complete WORKLOG here --> MM U2-UFO Duality dual loop
I tired slim the bitspower compression fittings for tygon 1/2 tubing will NOT fit the D-TEK fusion. They also will not work on the EK NB/SB max or the EK NB/SB ASUS 1.Quote:
Originally Posted by slim142
They do however work on the mosfets for the 790i EK-Mosfet ASUS 3a.
Go for Bitspower single water block solution for cooling the NB and SB in one shot, should be out soon. The holes are far apart 1/2 compression fittings look like they should fit no problem. This block will not inhibit 3X SLI if it's in your plans...looks killer too.
Hey trigger, thanks a lot for that info! I really needed that :up:Quote:
Originally Posted by Trigger5521
So I guess out of the 8 fittings I already have, I can use 4 at least :)
I say 4 because 2 for the D-tek V2 and 2 for the BT Black Freezer since in this picture, the holes look very close together :( I dont think compression fittings would fit in the Black Freezer
http://img355.imageshack.us/my.php?i...00x3003et4.jpg
One question real quick
Will I have any kind of problem (flow, restrictions) if I use compression fittings on the Rad, pump and Res and standard fittings on the CPU and NB blocks?
Also, does the D-tek GPU V2 support 1/2 compression fittings?
http://i183.photobucket.com/albums/x...h_P9090305.jpg
http://i183.photobucket.com/albums/x...h_P9090306.jpg
http://i183.photobucket.com/albums/x...h_P9090307.jpg
First WC build. It's not nearly done yet, still have to get my new GTX 280 and waterblock in, and this cheap hardware store vinyl tubing is getting replaced with some Primochill LRT 3/4" OD stuff. The PA120.1 is getting added to the loop when I get the GPU and GPU waterblock, same as the tee and fillport (which will be used as a drain line most likely, I like the Micro-res for bleeding). The rat's nest of wires is also getting cleaned up. For now it's just so the system is usable for school.
Clamps will be added when the build is up for reals, for the time being I'm ok with it like that, no leaks so far.
Silverstone TJ09-BW
Asus P5Q-Deluxe
Core 2 Quad Q6700 (lapped)
2 x 2GB Mushkin Redline PC2-8000
eVGA GTX 260 (soon to be replaced by a GTX 280)
2 74GB Raptor ADFDs in RAID0 for Vista x64 and programs (Well, one is an OEM 80GB meant for Dell, but that's not really important)
250GB WD Caviar 16MB
500GB Samsung SpinPoint 16MB
Creative Labs X-Fi XtremeMusic
OCZ 800w EliteXStream
And for the watercooling gear:
Enzotech Sapphire
D-tek Fuzion GF2 + 260/280 Uni-sink
Swiftech MCP355 with an XSPC DDC acrylic top
XSPC RS360 3 x 120mm radiator
Thermochill PA120.1 120mm radiator
Swiftech Micro-res
Bitspower 1/2" high-flow barbs
Bitspower acrylic T-fitting
Danger Den delrin fillport
Primochill 1/2" ID 3/4" OD LRT tubing, black
Primochill anti-kink coils, UV green
Distilled water + PT_nuke
My flow is fine with the mix and match between 1/2 compression and regular 1/2 barbs. Note I got the compression fittings on my rad(sig) and I got them on the RES using some of the funky koolance fittings. Swivel 90 and swivel 45Quote:
Originally Posted by slim142
see pic. No idea about the D-TEK GPU sorry.
very nice! trigger, do you gonna wc 8800gt's?
My PC
http://img520.imageshack.us/img520/4...6990oi5.th.jpg
http://img149.imageshack.us/img149/5...6995hd1.th.jpg
http://img149.imageshack.us/img149/6...6997ar8.th.jpg
http://img178.imageshack.us/img178/9...6998fs1.th.jpg
http://img149.imageshack.us/img149/6...7000yz1.th.jpg
http://img183.imageshack.us/img183/5...6789cc6.th.jpg
http://img140.imageshack.us/img140/7...6791lm3.th.jpg
http://img389.imageshack.us/img389/6...6809rd7.th.jpg
Intel Quadcore Q6600 B3 Lapped @ 3.6Ghz FSB 400 Prime 95 small fft Stable
EVGA 680i SLI A1
Ocz Reaper Pc 6400 DDR 800 4gig
3 Raptor X 150GB Raid 0
Western Digital 250GB
Western Digital 500GB
Maxtor 300GB
LG Sata DVD Writer
Galaxy 8800 GT 512MB Watercooled SLI
BFG 8800 GT 512MB Watercooled SLI
Creative SoundBlaster Audidy2 ZS
Kandalf LCS Case
Tagan BZ1100 watt Case mod for more cooling
Windows Vista Ultimate 64bit
Samsung 245BW 24" 1920/1200
CPU/Chipset Loop
Thermochill radiator PA120.2
Sythe UltraKaze 3000RPM
Sunbeam Rheobus Fan Controller
D-Tek Fuzion
Swiftech MCW30
7/16 Tubing
Mcp655 Pump
Swiftech MCRES-MICRO
Feser Orange
VGA Loop
Thermaltake Kandalf LCS Watercooling system 3/8 tubing and pump/reservoir
MCW60 with ramsink
Feser Acid Green
Vantec Nexus Fan controller
beaglekill you will see massive temp drops if you get rid of that thermaltake radiator, it's really restrictive
Oh and BTW, he means replacing it with another radiator :up:Quote:
Originally Posted by SSGWright
wow, loved the picture!Nice work m8:up:Quote:
Originally Posted by seba84_2005
Malik, that is amazing!
Nah the 8800Gt's are not worth enough to put blocks on em...going to upgrade to BFG 280's with water blocks later, just need to add another rad to the loop.Quote:
Originally Posted by pcaddict
Hey man, dont understimate the power of the 8800GT, I have two and Im very proud of having them ^^
Currently cant afford 280s and with the performance difference, is not worth in my case anyways.
Maybe, but my GT's are only 44° on load :)Quote:
Originally Posted by SSGWright
Heres the start of my Rig.....
http://i65.photobucket.com/albums/h2...Picture067.jpg
http://i65.photobucket.com/albums/h2...Picture070.jpg
http://i65.photobucket.com/albums/h2...Picture064.jpg
http://i65.photobucket.com/albums/h2...Picture065.jpg
http://i65.photobucket.com/albums/h2...Picture069.jpg
Hi my new mod;) highlighting the rad grill:D
http://images43.fotosik.pl/10/a4c184ca6fe47559.jpg
http://images25.fotosik.pl/274/56944ab05ebee188.jpg
and sleeve:D
http://images34.fotosik.pl/361/2ee15231a69ed112.jpg
http://images47.fotosik.pl/10/8ebefb686e7eda84.jpg
http://images34.fotosik.pl/361/ab1592a01e4526fe.jpg
http://images45.fotosik.pl/10/929d0c0ddb9181c7.jpg
I like! Nice job. :clap:Quote:
Originally Posted by seba84_2005
That is actually nice :OQuote:
Originally Posted by seba84_2005
look nice !:up:
Seba, how long did that 24 pin take you to sleeve? It looks gorgeous :up:
about 5 hours on all;)Quote:
Originally Posted by afireinside
Hey all!
Here is my rig...
http://www.aijaa.com/img/b/00351/2724233.jpg
http://www.aijaa.com/img/b/00239/2724224.jpg
OK now something from me :D
D-Tek V2 Nickel
http://img247.imageshack.us/img247/640/dtekv2wh7.jpg
http://img247.imageshack.us/img247/d...pg/1/w1024.png
http://img247.imageshack.us/img247/8813/dtekv02ai7.jpg
http://img247.imageshack.us/img247/d...pg/1/w1024.png
24pin sleeves.
http://img247.imageshack.us/img247/9899/oplotno8.jpg
http://img247.imageshack.us/img247/o...pg/1/w1024.png
PCI-E sleeve.
http://img526.imageshack.us/img526/3849/pcie01vf8.jpg
http://img526.imageshack.us/img526/3...140613974d.jpg
http://img526.imageshack.us/img526/4198/pcie02yj0.jpg
http://img526.imageshack.us/img526/4...c80a400b09.jpg
8800GT Alpha Dog & EK Fullcover
http://img526.imageshack.us/img526/3261/8800gtfq5.jpg
http://img526.imageshack.us/img526/3...d2ab6b6144.jpg
EK Water Blocks Multioption RES 150 rev.2.0
http://img45.imageshack.us/img45/2270/ztekstemku1.jpg
http://img45.imageshack.us/img45/zte...pg/1/w1024.png
Jeez 3 people in a row with their 24 pin sleeved that way. I think I'm going to be ordering some sleeving soon...
Nice pics snow
Wow! How'd ya get your hands on a D-Tek FuZion V2 nickel-plated?:confused::shocked:
Because we have sleevingmania in Poland :DQuote:
Originally Posted by afireinside
Quote:
Originally Posted by BeagleKill
Seems like you have a nice audio system aswell hehe.
Mind telling me more about that config?
Thanks
Yeah I saw that nickel plated V2 as well. Nice rigs from all. I am always amazed at how, each year, each month even, projects get better and better. And everyone has an idea somewhere on how to get things to work in limited space, how to make things look nice, very impressive work all around.
dude, that comp has such a steampunk style to it; its awesome:up:
BeagleKill, did you cut out a 120mm hole on the right side of your case towards the back and modify the PSU mounting to have it flipped, or is that how the case comes? I have a normal Armor case and have been thinking about modifying things to flip my PSU around to take cool air from outside rather than air from inside the case.
It's a home theater system:Quote:
Originally Posted by Astratuner
Onkyo TX-SR503 amplifier
2 reference tower (2X 5inch with tweater and 8inch woofer)
1 reference center
1 sub soundstage 15inch 400watt rms
I'm not runnig 5.1 , (next step soon :))
(photos soon)
Yeah, it's custom made !Quote:
Originally Posted by rehpyc
Have you already see that on a kandalf or armor case? :D
My PSu is less noisy and less hot!
Sorry for my english dude
http://img222.imageshack.us/img222/2...0us5vw0.th.jpg
while leak testing it
http://img502.imageshack.us/img502/8...4vc4jo3.th.jpg
with it closed
you can kinda see the custom made brackets i made to keep my rad in place up top ... they are painted black and do a very nice job of blending in haha
it also glows blue ... just havnt taken a pic of that yet ...
also tried to hide the wires as best as possible ... what ya think?
No, I haven't seen any pictures of it prior to yours, but it's something I've wanted to do as it seems practical and then allows you to use the hdd cage in the upper back w/o crippling the PSU.Quote:
Originally Posted by BeagleKill
Do you mind a pm to get some ideas as to how you approached it?
Did a little refresh, same case but a few new bits.
http://img82.imageshack.us/img82/9967/img0001pu6.jpg
http://img82.imageshack.us/img82/img...pg/1/w1024.png
I finished my WC rev 2 in 100%;) how you like him?:up:
http://images33.fotosik.pl/367/efedb13f1fc90ad0.jpg
http://images35.fotosik.pl/10/936c1bfae4b02871.jpg
http://images34.fotosik.pl/361/3dedba0c94259c97.jpg
http://images33.fotosik.pl/367/62609c8b8705788f.jpg
http://images31.fotosik.pl/362/d0ba647ef2586080.jpg
http://images28.fotosik.pl/275/23eb1c18bdb01a61.jpg
http://images32.fotosik.pl/361/c92603083f3d9905.jpg
http://images47.fotosik.pl/10/b284c94b57a94e51.jpg
http://images45.fotosik.pl/10/bbb2bc089abe1dfa.jpg
http://images32.fotosik.pl/361/634363fcb94975c4.jpg
http://images39.fotosik.pl/10/2e0267ea6915dc39.jpg
http://images26.fotosik.pl/275/f5fc5d5182d98796.jpg
http://images26.fotosik.pl/275/a7fb5df40e4618e7.jpg
http://images43.fotosik.pl/10/d391e4318fd1731c.jpg
http://images28.fotosik.pl/275/6f8bf7c85fa9ce63.jpg
http://images32.fotosik.pl/361/3f6f77044802d4cc.jpg
http://images32.fotosik.pl/361/f078b112b1fc6003.jpg
soon rev 3:D
great looking system seba :)
everytime i see i beautiful system like yours using 3/8" tubing it makes me wonder if i should starting using that size.. Ive been using 1/2" or now 7/16" tubing since probably 2000..lol
from the looks of your setup youve been using watercooling for a while so im sure youve used 1/2" and probably 7/16" tubing at one time or another..
Do you notice any significant temp differences with using the smaller tubing???
thanks
CCC
Nice, same board same kind of setup :) :up:
Only yours looks better lol.... any pic of the PSU and the wires that come out of it?
temperature without changes on these tubes;)Quote:
Originally Posted by CCC
Quote:
Originally Posted by CCC
I know
Sebas system is making me jealouse (SERIOUSLY) haha :p:
If I knew that Bitspower fat fittings only fitted with 3/8, I would have probably used 3/8, but hey, 1/2 aint that bad neither!
Seba...nice looking system, and great shots too!
Slim, BP makes 3/8" fittings too. Heck, you could get their 7/16" fittings and put 3/8" over them for a tight seal.
Beautiful stuff, Seba.
I'm going to use those same fittings and tubing on mine. :D
That is A LOT of tubing! To cut down on that, you should have turned the radiator upside down, and had the tubing go directly through the top through some custom made holes.Quote:
Originally Posted by Copenhagen69
3/8" for world domination! There is seriously no point with anything bigger except bragging rights. And compensation for something else.
^^^ |+1 :D i use 3/8" on ek 1/2 barbs so tight no chance of getting it off and looks so much better no clamps :D
That's one hell of a system seba :D That must be a pain in the ass to keep it clean from dust :p:
How did you cut your window so nice ? With a waterjet or ...
I cut out the window Dremel 300;)Quote:
Originally Posted by Zw_Roodbaard
[QUOTE=seba84_2005;3288035]I finished my WC rev 2 in 100%;) how you like him?:up:
http://images33.fotosik.pl/367/efedb13f1fc90ad0.jpg
http://images35.fotosik.pl/10/936c1bfae4b02871.jpg
Hi Seba great system but u need to sleeve VGA power cables too.
This is my first post on this forum so I thought the best idea would be to post some photos of my rig.
I can say that many of the builds on here have inspired my own build.
Looking cool there Whilhelm :clap:
Thanks. I put the system specs in my sig.
Whilhelm, nice clean rig you got there.
BTW :welcome:
Whilhelm, Nice pc! and Welcome to XS!
http://www.abload.de/img/img_4109lmr.jpg
Cheers! :D