ok, thank you for your feedback :up:Quote:
Originally Posted by donmarkoni
Printable View
ok, thank you for your feedback :up:Quote:
Originally Posted by donmarkoni
Got it up and running finely the Corsair memory 2000MHz anyhow XMP detects it and sets it to the correct specs.
man forget xmp it will set voltages verry highQuote:
Originally Posted by USFORCES
set it manualy
From what a few people told me 1.65 is fine?Quote:
Originally Posted by zsamz_
Question the 6G sata wires those go to any sata hardrive, I plugged them in and they weren't detected so I switched, anyhow what the deal with them?
^^1.65 VDimm or 1.65QPI/VTT? What is your QPI set to when you use XMP? I think thats what zsams is referring to.
vdimm i wouldnt care if it was 1.7 max but qpi no way my old hyperx set qpi vtt to 1.65vQuote:
Originally Posted by OC Nub
Thanks for looking out,
qpi 1.25v is it ok or too high?
nope you real goodQuote:
Originally Posted by USFORCES
i push as high as 1.45v
I forgot to mention this but when I replaced the stock heatsink on the board yesterday I noticed the heatsink totally skips rows of mosfets and the EK block covers them they must not be the important mosfets :p
Am thinking of getting 2 Crucial RealSSD C300 64GB and raiding them in sata3 6.0 is that possible with this board! Or can it only raid in sata 2!
Do you guys know of any settings I need to change (or possibly jumpers) to boot with a PCI video card? I'm setting up for some high PCI-E runs but I can't get it to boot with the 440 FX or whatever the hell it is. The seller confirmed that it worked and it starts, but the board hangs on VGA.
Any suggestions?
running with an old matrox pci vga card my tests right now. there were no special settings required. everything at default boots without any problems.Quote:
Originally Posted by bassplayer
so yes it should be possible. may be just some sort of incompatibility between the r3e and your card. try another pci vga card ...
Quote:
Originally Posted by bro20000
Marvell Sata 6Gbps RAID is really weak. Avoid like the plague. You can still use ICH10r for raid and you will be better off, other than that you are stuck with buying a PCI-E controller.
Page 100 ! GG
Is it like this: http://www.xtremesystems.org/forums/...es#post4437898Quote:
Originally Posted by USFORCES
There is picture and explanation. If it's like that, then you are OK. :up:
Hi all, thinking of buying a RE3 when I shortly make the move to socket 1366. If I have EVGA gpu's will there be any performance issues running them on an Asus board? Stupid question I'm sure but I've never really had multiple brands in this area.
There chokes? Well mine are now water cooled chokes :p:Quote:
Originally Posted by donmarkoni
No issues, don't worry. :welcome:Quote:
Originally Posted by fendog
:D Yeah, big black ones are chokes and small silver ones are MOSFETS.Quote:
Originally Posted by USFORCES
Yes! 100 pages! Congratulation to everyone on good advices and experiences shared here! :clap:Quote:
Originally Posted by AceBaran
:ROTF:Crazy man iam feeding Qpi volt on air 1,63v and pci-e at 113Mhz, Bios 1003 to get this http://valid.canardpc.com/show_oc.php?id=1373064
i have strong cpu and its alive yet :up: Vdimm at 2,5v tested to and not killed mem controller.... :eek:
:D
^to you too donmarkoni
http://hwbot.org/community/submissio...eme_250.34_mhzQuote:
Originally Posted by PytonOrm
You shouldnt need that many volts man, dont kill it! :eek:
up please :DQuote:
Originally Posted by tistou77
:D trying Qpi at 1,72v now :rofl: still live bclk at 247 and then alot of blue screens
Noooo... :eek: As Splave said, don't kill it. :(Quote:
Originally Posted by PytonOrm
No, it's not, check this out: http://www.xtremesystems.org/forums/...postcount=2355Quote:
Originally Posted by tistou77
You don't need to kill it, you can always send it to me, and I'll keep it warm and cozy. :DQuote:
Originally Posted by PytonOrm