Printable View
just solder directly to the leg ;) no need to desolder anything.Quote:
I can't really tell in most of the pics as most of them aren't closeups, but when soldering the wire to one of the chips would you first desolder the post that you wanted, lift it up off the motherboard and then solder the wire to it or can it still be attached to the wire and the motherboard at the same time?
Lo, I only scanned the thread, but did you get your Mobile going on this mobo?Quote:
Originally posted by Jeff
The two mounting holes for the mobo align themselves right down the center of the northbridge. Someone creative(unlike myself) could probably figure something out using those too. ;)
Just wondered as I just booted mine :D
Cheers
You just booted your mobile? As far as I know your the only person that may be successful with this board and a mobile, Jeff posted that his was incompatable and he sold off his mobile. Another fella posted also that his incompatable. Please list your details such as your board revision, Processor type and model #, and bios revision.
I could get it working if I used a desktop chip to set it the multiplier. "Auto" wouldn't work for me and didn't allow my setup to get past the "C9" BIOS code.
The bummer for me happened when I had the mobile running and I pushed too hard. The BIOS would reset and I'd have to swap back my desktop CPU to get the mobile working again. That's just not fun when your trying to have fun. ;)
Lo, mines ok, well had to vmod the vcore because it defaulted to high multi/low vcore = x9/ 0.9v. Volt mod to 1.3v and voila boots.
Only problem so far is I can't get passed 270 FSB, the PCI doesn't seem to be locked ? I thought the Epox had PCI lock?
Edit, this board is weird :(
Cheers
Lo, my motherboard is v1.0, not sure on the chip, it's alittle tied up atm :)
I did the same on a K8NNXP, just had to mod the vcore before it would boot. I posted a thread in the vapochill forum.
http://forum.vapochill.com/showthread.php?threadid=7052
Cheers
Well goto the 300 barrier, it seems to be stable, 1 more mhz and it locks.
Does anyone know wich mosfet i can read the Vcore?
The 2 mosfets aroud the ATX connec, gives me strange vcore.
Lo, I measure mine on one of the coils. The leg nearest the I/O panel. Top left, can't miss them.
Cheers
thxn, now ive got better measering. 1.59v instead of 1.48vQuote:
Originally posted by Bulldog20
Lo, I measure mine on one of the coils. The leg nearest the I/O panel. Top left, can't miss them.
Cheers
This only cause i picked another ground (probe).
I picked a molex 4 pin for getting my ground. There are 2 black. (GND) Two ground give me 2 different measering.
Why...
wait so did it not boot initially and did boot with a vcore mod????Quote:
Originally posted by Bulldog20
Lo, mines ok, well had to vmod the vcore because it defaulted to high multi/low vcore = x9/ 0.9v. Volt mod to 1.3v and voila boots.
Only problem so far is I can't get passed 270 FSB, the PCI doesn't seem to be locked ? I thought the Epox had PCI lock?
Edit, this board is weird :(
Cheers
or it booted out of the box except with 0.9v vcore????
how come this guy can get mobiles working and no one else can???
Yes m8, just a vcore mod. So out of the box with a vcore mod. I posted this on my forum weeks ago.
"how come this guy can get mobiles working and no one else can?? "
What does that mean? Not sure if there is a complement hidden in there somewhere :) I have been clocking for a little while ;)
Cheers
When I measure there, I get 1.3V when it's set to 1.7 in the BIOS. That can't be good.Quote:
Originally posted by Bulldog20
Lo, I measure mine on one of the coils. The leg nearest the I/O panel. Top left, can't miss them.
Cheers
Lo, a yes it works here from that point, either bios adjustment or pot.
Cheers
Do these mod's work on the J version as well instead of the +?
YES
COOl thank's I guess I will have to read this whole thread when I get my board LOL
So is THIS still the best bios floating around??
And where are people getting this 1:1 FSB/DRAM in cpu-z from?? All I get is "CPU/#".
Just a thanks for the vcore/vdimm mods. Have not done the vcore yet however the vdimm mod along with 6/14 flash changed the board dramatically for me. RBX along with 3.1v on ram and she will run to 2727 primed. Will boot and do some light benching at 2750 (cpugen is overvolting to 1.85v under load). Used 10kvr on vdimm. SuperPi 1 meg is 33 seconds, 2 meg 1 min 16 secs. and 6800gt w/ultra flash is doing 28,100 (27,100 without). Chip is 3000+ Newcastle. 9 x 303 at (166) 2,2,2,5 1T 4x. Vdimm is a good mod. Ran the 320w tec past DD on a maze 2-1 and they think on the 1/4 inch plate and 1/2 nipples the block should handle 10v. Will be giving it a go along with the vcore mod and dual rads in cooling box. 2.8Ghz should be achievable, now as for 2.9Ghz.....that is another story.
if the # in CPU/# is the multi that ur running then youre in 1:1, if its 2 higher ur in 183, or 166 which is like 5:4 or something i thinkQuote:
Originally posted by Jade
So is THIS still the best bios floating around??
And where are people getting this 1:1 FSB/DRAM in cpu-z from?? All I get is "CPU/#".
Hmmm, I cant get mine to 1:1. THe lowest it goes to is cpu/10....when my multi is 8x. If I raise my multi the cpu/# just goes up! >_<
These a64s confuse the crap outta me. The more I read about them the more I am lost.
Can someone takes some pic's of there mod's so I can have something to go by the one's on the 1st page have seemed to stop working?
Jonspd
Heres the origonal pic of the Vcore mod.. I believe the line you see goes from that leg to a 20 or 50 Vr then to ground.
I'll look for the vdimm on the other computer in a few mins. Playin DOOM 3 on it now :) Damn whata game baby!
Haha, I know how you feel. I love that it explains why there is no duct tape for everyone asking "why can't you duct tape the light to thegun"Quote:
Originally posted by eclypse
I'll look for the vdimm on the other computer in a few mins. Playin DOOM 3 on it now :) Damn whata game baby!
Heres the other pics of the VDIMM.. Just encase you cant reach the site hosting them cause they seem to work for me.