Printable View
Hehe. I once got 3.88V dimm voltage due to a short circuit... could not even get into windows...Quote:
Originally posted by iceman2g
SAE or anyone reading this do where's the vdimm check point on the board. I no longer get a reading in the bios. I tryed searching but found nothing.
Edit:Ok I found it. Whoa I was pushing 4.2V through these Bh-5 sticks. I was turning pot the wrong way.
Yeah I got into windows no problem. You guys are so lucky with these 2.9ghz chips. I'm stuck at 2.66ghz, if anyone has a chip that does 2.7ghz on air i'm interested. The chiller needs a new toy.
phobix do you have any sinks on the memory? Mine get real hot without and that's only at 375.
How hard is the vsense mod to do? I've already done vdimm. I can't get over 1.9v vcore wtihout board rebooting. I'm sure this has already been covered but the vsense is for those going over 2.1v correct?
Vsense is not really needed. You should only do the vcore mod at pin7 and set vcore in bios at 1.825V. Then turn up resistance until you get 2V to 2.08V... more ain't stable.Quote:
Originally posted by iceman2g
How hard is the vsense mod to do? I've already done vdimm. I can't get over 1.9v vcore wtihout board rebooting. I'm sure this has already been covered but the vsense is for those going over 2.1v correct?
Would that solve my porblems going over 1.9v? Also I want the pot set to 0 then turn it up to increase voltage correct (don't wanna repeat what I did with psu and vdimm)?
@iceman2g:
I am running without sinks on my Raddy as all is still running stock volts. My BGA's were not getting that hot last night, but when I will perform the VDD, VREF, and VDDQ mods I will make sure to sink the BGA as this will increase the heat some.
That's a beautiful overclock for stock voltage. The most mine will do stock is 495/375. I've tryed 380 but get artifacts, 500 on the core kicks be back to desktop more often than not so I can't get a good run.
Hmm I missed a whole bunch of replies in 2 days or so :DQuote:
Originally posted by iceman2g
Garrett what bios are you using for your 9800Pro? It's only 128MB but your using a XT bios? Which one might I ask and have you seen an increase in performance? Also do you have R360 or R350 core?
Anyway, I'm using a Club3D 128MB 9800XT Hynix bios :D
http://www.mvktech.net/download.php?view.307
I could get about 10mhz more on the core, but since I got it vmodded that wasn't much :D
I have a 360 core :thumbsup:
The card is a Club3D 9800pro 128MB with Hynix memory (2.8ns)
I get 7191 3dmark03 with non-FM approved drivers... not that I give a ~tihs~ ;) :D
What kind of BGA do you have? Is it Hynix or Samsung? I prefer Hynix as I have always had better luck with them over Sammies. However, as you know already it is the luck of the draw rule that applies here. Have you done any Vmods on the Raddy yet?Quote:
Originally posted by iceman2g
The most mine will do stock is 495/375.
Hmm. I don't remember, but you have to set pot to max resistance with this mod (vcore)... otherwise the board would not start or even be damaged.Quote:
Originally posted by iceman2g
Would that solve my porblems going over 1.9v? Also I want the pot set to 0 then turn it up to increase voltage correct (don't wanna repeat what I did with psu and vdimm)?
Could solve your probs... but I can only repeat what I said. Solder a 50k pot set to max to pin7 of the hip, then ground it, and set bios vcore to 1.825V and then turn up the voltage in bios till you see 2V or such...
Ok, but you got the sucker voltmodded right?Quote:
Originally posted by SAE
It's by far not artifact free... :(
522 gets me really funny snow on the screen... hehe. Okay, not as much as 530 though :lol: Only the white sh1t anyway... sometimes it seems as you could see through where the edges of the geometry/textures meet...
And I guess 500 core IS artifact free hmmkay? ;)
Dunno exactly as I recently changed pelt psu (400W antec at 12.6V -> load 12.3V) and reseated the cooler. But when I got the card last juli it was artifact free at 500 and stock voltage... but it wasn't this year anymore :( Have to check :DQuote:
Originally posted by Garrett
Ok, but you got the sucker voltmodded right?
And I guess 500 core artifact free hmmkay? ;)
BTW. Only snow, nothing else - with subzero it would very likely get less snow ;)
Well I have a few snow pixels @ 480, nothing in-game though so I'm hoping for an improvement with the MCW50-T...Quote:
Originally posted by SAE
Dunno exactly as I recently changed pelt psu (400W antec at 12.6V -> load 12.3V) and reseated the cooler. But when I got the card last juli it was artifact free at 500 and stock voltage... but it wasn't this year anymore :( Have to check :D
BTW. Only snow, nothing else - with subzero it would very likely get less snow ;)
/edit. Funny :lol: I got ya before you edited, hehe
PS please remove my quote piece, something really got screwed up there :( and it looks kind of n00bish :(
Sorry SAE, but your score just got trounced:
http://service.futuremark.com/compare?2k1=7734472
I don't know who did this, but don't you just love bugged scores?
LOL :D
3DMark Score 27316 3D marks
Game 1 Car Chase - Low Detail 150.4 FPS
Game 1 Car Chase - High Detail 805.0 FPS
Game 2 Dragothic - Low Detail 209.9 FPS
Game 2 Dragothic - High Detail 126.5 FPS
Game 3 Lobby - Low Detail 191.1 FPS
Game 3 Lobby - High Detail 91.7 FPS
Game 4 Nature 67.0 FPS
man thats one fast computer!!! :D
I have hynix 2.8ns.Quote:
Originally posted by phobix
What kind of BGA do you have? Is it Hynix or Samsung? I prefer Hynix as I have always had better luck with them over Sammies. However, as you know already it is the luck of the draw rule that applies here. Have you done any Vmods on the Raddy yet?
Garrett did you do a comparisant at the same setting to see if there was any improvement using that bios? Clock for clock isn't the XT suppose to be at least 5% faster than the Pro.
I've been able to find nothing on a Club3D 9800XT 128MB. Aren't all XT suppose to be 256MB?
No I didn't compare them, don't expect it to be (much) different.
I'm aiming for the highest possible core speed :D
Hehe. The nature score alone is priceless ;)Quote:
Originally posted by Cactus Jack
Sorry SAE, but your score just got trounced:
http://service.futuremark.com/compare?2k1=7734472
I don't know who did this, but don't you just love bugged scores?
:D
Okay, no2 now :(
Should do, but I know nothing about GF-cards now ;)Quote:
Originally posted by µnrealneo²
^Bump^
DO you reckon a 520+/1050+ FX5900 & psychodil's 240 x 11 Barton would break 22K? :D
I bet we'll have a go some time. ;)
21K is my goal with 247 x 10 2-2-2-10 SC Tbred. :)
I have a nice score on plain aircooling:
http://service.futuremark.com/compare?2k1=7872495
22512 3d marks with a fx5900xt @ 600/930
Nice score, better score cause it's 5900xt :D :thumbsup:Quote:
Originally posted by HaLDoL
I have a nice score on plain aircooling:
http://service.futuremark.com/compare?2k1=7872495
22512 3d marks with a fx5900xt @ 600/930
I think this thread should be stickied, it shouldn't be slipping down to page 3!
The message in my sig still stands, btw. Does anyone fancy taking on the job?
some nice scores in this thread, would love to be able to break 22k with my rig but i just don't think it's gonna happen. oh well. maybe next upgrade
I am sorry that I did not come back to ya yet... Gaz, but I am still interested :)Quote:
Originally posted by Cactus Jack
I think this thread should be stickied, it shouldn't be slipping down to page 3!
The message in my sig still stands, btw. Does anyone fancy taking on the job?
We should meet again on msn later and you could help me to register there... do not remember all the details anymore ;)
Been busy with exam - studies... I must apologize...
You can just send me a message, I should see it and answer (always shown as offline IMO)... in case I am on the internet rig :D
Sorry again as I did not want to be unreliable :(
P.S. I also VOTE FOR A STICKY! :D :thumbsup: