**[OFFICIAL]** GIGABYTE Z77X Owners Club/Discussion/Info (All Model's Welcome)

Quote:

---

Originally Posted by acebmxer

Yes correct. You have to flash the one bios then flip the switch and flash the other bios.

---

okay thank you!

Last night I got a pretty stable 4.6 ghz overclock (11.5 hrs LinX w/ AVX). This is on air with a NH-D14.
One problem: I have to use LLC set to Extreme. With LLC Turbo, the Vdroop is ~0.025V (from 1.272 -> 1.248), and linX fails in ~30 min. With LLC Extreme, the Vcore is rock solid at 1.272V in CPU-Z (though not sure about REAL Vcore) and gives me 100% stability.

Would it be okay keeping LLC Extreme for 24/7 usage? Or, should I just use LLC Turbo and more voltage to compensate for Vdroop? I'm still not 100% sure on safe 24/7 Ivy Bridge voltage so I'm trying to raise Vcore slowly and only when I really need to.

Quote:

---

Originally Posted by MannerRev

okay thank you!

Last night I got a pretty stable 4.6 ghz overclock (11.5 hrs LinX w/ AVX). This is on air with a NH-D14.
One problem: I have to use LLC set to Extreme. With LLC Turbo, the Vdroop is ~0.025V (from 1.272 -> 1.248), and linX fails in ~30 min. With LLC Extreme, the Vcore is rock solid at 1.272V in CPU-Z (though not sure about REAL Vcore) and gives me 100% stability.

Would it be okay keeping LLC Extreme for 24/7 usage? Or, should I just use LLC Turbo and more voltage to compensate for Vdroop? I'm still not 100% sure on safe 24/7 Ivy Bridge voltage so I'm trying to raise Vcore slowly and only when I really need to.

---

Use turbo with more vcore. Extreme overvolts, turbo is spot on measured with a DMM. CPU-Z shows it dropping when its not.

for a 24/7 overclock, do you think 1.3V would be too much on AIR? or 1.35V too much? (for Ivy Bridge) I can't seem to find anything that tells me safe voltages for Ivy Bridge, and i'm scared to test myself :P

Having problems getting over 4.5 ghz on water :(

The Vcore is jumping around idle its 1.6ghz at 1v then under load it jumps to 1.31v which IMO is too high and I have it set in bios to 1.28v

Also core #2 in Core Temp is well above the others

Attachment 127493Attachment 127492

I don't mind the system stepping down to save power but its going well above my set point.

is there a bios thread that shows what people are set at for stability???

try to set an offset and see how that does. the vcore going to 1.31v is SVID you will have to try offset.

1.31 VID @ 4.55 seems really high to me, and your temps are a little uneven. 99c on one, 70c on the other? wow! :P you could try remounting your water block to see if that helps the temps

i got my UD3 now, and first my logitech classic 200 and mx518 no support when i install windows, i have to use an usb hub on the boards f_usb1 connection, then it works...
then i have testet my cpu to 5ghz at 1.31 on air on 2 other boards, i can do that to on the ud3 boot in windows and stabil in superpi 32m, but when i restart and go in bios it freez, and i have go above 1.45, then it dont... i have used the F10, F11a, F11b bios and same same
do Gigabyte have an unofficial OC bios ? i can see some are using an 04 bios.. please send a PM if i can have that bios :)

I have the G15 Keyboard and The MX518 mouse. The mouse works just fine in bios and windows setup when using the 2 usb ports located directly below the ethernet ports. Or when using a PCi USB front header connection. This has worked since bios F5 for the UD3H for me.

Quote:

---

Originally Posted by Rosty

i got my UD3 now, and first my logitech classic 200 and mx518 no support when i install windows, i have to use an usb hub on the boards f_usb1 connection, then it works...
then i have testet my cpu to 5ghz at 1.31 on air on 2 other boards, i can do that to on the ud3 boot in windows and stabil in superpi 32m, but when i restart and go in bios it freez, and i have go above 1.45, then it dont... i have used the F10, F11a, F11b bios and same same
do Gigabyte have an unofficial OC bios ? i can see some are using an 04 bios.. please send a PM if i can have that bios :)

---

you will freeze in BIOS if your OC is not stable. 5ghz 1.31v on ivy bridge? the UEFI puts a load on the CPU.

Quote:

---

Originally Posted by acebmxer

I have the G15 Keyboard and The MX518 mouse. The mouse works just fine in bios and windows setup when using the 2 usb ports located directly below the ethernet ports. Or when using a PCi USB front header connection. This has worked since bios F5 for the UD3H for me.

---

yes sorry, install win 7 and MX 518 working, and the keyboard works with ps2 adapter :)

Quote:

---

Originally Posted by sin0822

you will freeze in BIOS if your OC is not stable. 5ghz 1.31v on ivy bridge? the UEFI puts a load on the CPU.

---

yes 1.31v, and with memory at 1200mhz+ 1.35v

ok, can see the temp increase when i go to bios :)

thanks for the reply, I test a little further and try with something ln2 this weekend and see how it goes :)

nice to see you playing with UD3H Rosty :)

Quote:

---

Originally Posted by iboomalot

Having problems getting over 4.5 ghz on water :(

The Vcore is jumping around idle its 1.6ghz at 1v then under load it jumps to 1.31v which IMO is too high and I have it set in bios to 1.28v

Also core #2 in Core Temp is well above the others

Attachment 127493Attachment 127492

I don't mind the system stepping down to save power but its going well above my set point.

is there a bios thread that shows what people are set at for stability???

---

Do you have the UD3 or UD5?

The three Ivy's I tested did 4.5 stable with 1.25V, so Id set it manually there, and put LLC on Turbo. Dont trust CPU-Z or software either.

Also, for your temp differences, did you spread the TIM or do a dot in the middle? See here,
http://hardforum.com/showthread.php?t=1697037

Spreading for more contact area, and a thinner application then the dot method, does best with Ivy.

Quote:

---

Originally Posted by MannerRev

for a 24/7 overclock, do you think 1.3V would be too much on AIR? or 1.35V too much? (for Ivy Bridge) I can't seem to find anything that tells me safe voltages for Ivy Bridge, and i'm scared to test myself :P

---

Too early for anyone to tell just yet. I always do the VID + 10-15% rule. Say your vid is 1.15V, then 1.265-1.3225V should be fine daily if your cooling is good enough.

New BIOS is out.

Quote:

---

Originally Posted by stasio

New BIOS is out.

---

Thanks Stasio :up:

New feature: Legacy Benchmark Enhancement in Misc Settings :D

Quote:

---

Originally Posted by dinos22

nice to see you playing with UD3H Rosty :)

---

yes nice board, and a very nice price to, and the performance in 32m is great :)



Thank you Stasio :)

BIOS F9c is not setting more than 1.848 vdimm & 1.322 vcore measured on a DMM..... Can anyone else confirm this?

The board also reports this not just a DMM.

### Edit ###

Cant get past 1.848 vdimm but vcore goes higher.

Bios 1.35 DMM 1.308
1.36 - 1.32
1.37 - 1.32
1.38 - 1.332
1.39 - 1.344
1.4 - 1.356 ..... didnt test higher

There's also another new feature in Periferals - Trusted Computing.... TPM Support.... didnt look fast so left it alone!!

Also the Legacy Benchmark Enhancement dont do nothing for me & Spi 32M

yea F9c has voltage issues, other users reporting this as well.

Can someone post his 2600K / UD5H 4.5Ghz settings?

Thanks

Quote:

---

Originally Posted by deNordic

Can someone post his 2600K / UD5H 4.5Ghz settings?

Thanks

---

Here is some profiles,but not with 2600K:
http://www.overclock.net/t/1239993/o...#post_17169608

Quote:

---

Originally Posted by C-N

BIOS F9c is not setting more than 1.848 vdimm & 1.322 vcore measured on a DMM..... Can anyone else confirm this?

The board also reports this not just a DMM.

### Edit ###

Cant get past 1.848 vdimm but vcore goes higher.

Bios 1.35 DMM 1.308
1.36 - 1.32
1.37 - 1.32
1.38 - 1.332
1.39 - 1.344
1.4 - 1.356 ..... didnt test higher

There's also another new feature in Periferals - Trusted Computing.... TPM Support.... didnt look fast so left it alone!!

Also the Legacy Benchmark Enhancement dont do nothing for me & Spi 32M

---

F9d is out.

Hey what happened to the thanks button round here? I was just starting to get the hang of it lol

Anyway thanks Stasio

yea haha it is gone, i guess they didn't like it? or it was making things slower?

New bios looks & runs fine so far. few new things like csm??? & control of int pll over voltage.... dont think it makes an difference having control but i like it.