"It has started"......Teasing pics.....

Printable View

Show 100 post(s) from this thread on one page

12-07-2006, 01:26 AM
hipro5

Quote:

Originally Posted by zbogorgon

and you use that 210cmf delta unprotected?

Well.....I'm fool I know......I've cut my fingers a couple of times....:(
12-07-2006, 03:14 AM
kiwi

But there is no glory without blood, isn't there? :p: :D
12-07-2006, 09:54 AM
Zeus

Yeah, pain is temporary, pride is forever. :D

Good luck with SLI setup Hipro5, show us 100K '01 Hiprostyle. ;)
12-07-2006, 10:14 AM
hipro5

Some bad news for me.......:(

I desided today to insulate k|ngp|in's Tek-9 LN2 VGA container so as to put it on the secondary VGA that hasn't cold bug and during insulation, I was taking pictures of the project with my digicam......
After the third round of insulation, the container couldn't stand straight up and while picturing it, it started to go down...So I tried to catch it "on air" while on my other hand I was holding my digicam....
During this, the digicam goes down the ground and I catch the container.....
After some inspection of the digicam, I see that the ccd chip inside the lens has been broken and I see blank in the LCD.....
Losses: one olympus 8Mp digicam.....:(
12-07-2006, 10:15 AM
Gautam

:eek2: No words.
12-07-2006, 10:17 AM
TaPaKaH

lol :D

feel sad about your cam, though :(

Tried RMA? :D
12-07-2006, 10:18 AM
Gautam

Quote:

Originally Posted by hipro5

Some bad news for me.......:(

I desided today to insulate k|ngp|in's Tek-9 LN2 VGA container so as to put it on the secondary VGA that hasn't cold bug and during insulation, I was taking pictures of the project with my digicam......
After the third round of insulation, the container couldn't stand straight up and while picturing it, it started to go down...So I tried to catch it "on air" while on my other hand I was holding my digicam....
During this, the digicam goes down the ground and I catch the container.....
After some inspection of the digicam, I see that the ccd chip inside the lens has been broken and I see blank in the LCD.....
Losses: one olympus 8Mp digicam.....:(

:( Sorry about that...but better the camera than the container, right? :p:
12-07-2006, 01:02 PM
Brettbeck

Sorry to hear about the camera! Try insurance...we did with a video camera my dad dropped, and we got it replaced with a brand new top of the range one :D.

BTW, whats gas is that in the pictures?
12-07-2006, 02:17 PM
esdee

Quote:

Originally Posted by Brett

Sorry to hear about the camera! Try insurance...we did with a video camera my dad dropped, and we got it replaced with a brand new top of the range one :D.

unfortunately after sales support is not that good in greece.
George you might have a chance if rmaing it if theres no physical damage to the camera

Quote:

Originally Posted by Brett

BTW, whats gas is that in the pictures?

ethylane ;)
12-07-2006, 10:50 PM
hipro5

Quote:

Originally Posted by Brett

BTW, whats gas is that in the pictures?

It's R507 and R1150....
12-08-2006, 08:17 AM
Ehwaz001

Quote:

Originally Posted by hipro5

Some bad news for me.......:(

I desided today to insulate k|ngp|in's Tek-9 LN2 VGA container so as to put it on the secondary VGA that hasn't cold bug and during insulation, I was taking pictures of the project with my digicam......
After the third round of insulation, the container couldn't stand straight up and while picturing it, it started to go down...So I tried to catch it "on air" while on my other hand I was holding my digicam....
During this, the digicam goes down the ground and I catch the container.....
After some inspection of the digicam, I see that the ccd chip inside the lens has been broken and I see blank in the LCD.....
Losses: one olympus 8Mp digicam.....:(

Damn, sad to hear. :(
I would try insurance anyway. If you don't try, you loose for sure...
12-08-2006, 10:40 PM
hipro5

I do not know if these digicams are covered of insurance.......I'll pay for my mistake as I always do.......:(
12-09-2006, 11:08 AM
[cTx]Philosophy

Say your cat/dog knocked over the tripod or something so as it not to be at ur fault..

Still impressive scores, keep pushing for 100k
12-09-2006, 11:39 AM
S1mon-

Nice work Hipro ;)
12-11-2006, 12:15 AM
hipro5

Some photos that where left in the memory card of my dead digicam.......I've pulled them out with HP Printer that reads memory cards....:)

Unfortunatelly, I didn't take any other shots with the finished LN2 container fully insulated due to digicam got dead....:(

http://www.thelab.gr/images/Hipro5/C...sulation_1.jpg

http://www.thelab.gr/images/Hipro5/C...sulation_2.jpg

http://www.thelab.gr/images/Hipro5/C...sulation_3.jpg

http://www.thelab.gr/images/Hipro5/C...sulation_4.jpg
12-11-2006, 05:08 AM
k|ngp|n

Looks beautiful George :D. I know you are limited with the insulation on the smaller pci-ex spaced boards. I used a few layers of tape insulation on older nv mobos too.
I feel bad about your camera though. What the coldest you've run the non-bugged ATI card at yet with it?
12-11-2006, 05:54 AM
hipro5

Quote:

Originally Posted by k|ngp|n

Looks beautiful George :D. I know you are limited with the insulation on the smaller pci-ex spaced boards. I used a few layers of tape insulation on older nv mobos too.
I feel bad about your camera though. What the coldest you've run the non-bugged ATI card at yet with it?

At -131*C base sensor of the container.....Below that, it kicks out with cold bug..... :(
12-11-2006, 06:07 AM
m411b

Sweet!
12-11-2006, 08:55 AM
k|ngp|n

Quote:

Originally Posted by hipro5

At -131*C base sensor of the container.....Below that, it kicks out with cold bug..... :(

That's great for ATI vg though no?? last card I ran that cold loaded was x850xtx around -140c. That was with chilly's gpu unit.

I would KILL to see pictures of my unit on there loaded up at -131c mid-bench on your ATI rig :slobber: maybe with a shot of the monitor in there too running 01 or 05. I want it for my site...When you get replacement camera :D?
And how about the 06' numbers with that rig? Kinc's early x1950 runs looked promising but he never finished with the conroe. With your cpu speed the dual-core 06' score is probably way up there over 18k I would imagine
12-12-2006, 05:30 AM
esdee

Quote:

Originally Posted by k|ngp|n

I would KILL to see pictures of my unit on there loaded up at -131c mid-bench on your ATI rig :slobber: maybe with a shot of the monitor in there too running 01 or 05. I want it for my site...When you get replacement camera :D?

If you want some for your site ill bring my nikon D50 to ensure the result ;):toast:
12-13-2006, 08:15 AM
hipro5

I was a bit confused today and I spent the LN2 just like that!..:(

No big deal though.....some updates.....:)

http://www.thelab.gr/images/Hipro5/C...4MHz_9.219.png

http://www.thelab.gr/images/Hipro5/C...83MHz_2385.png

http://www.thelab.gr/images/Hipro5/C...5MHz_17.81.png

......BUT I promise you that tomorrow, I'll pull down the Super-Pi 32M WR and not only.....;) :D

.
12-13-2006, 08:20 AM
TaPaKaH

Quote:

I'll pull down the Super-Pi 32M WR

this I got to see ;)
12-13-2006, 08:37 AM
LittleDevil

@hipro that is really great chip, we need chip like that too :p: :p:

regards
12-13-2006, 08:47 AM
hipro5

Quote:

Originally Posted by TaPaKaH

this I got to see ;)

00.06.531
00.26.828
00.50.453
01.13.984
01.37.375
02.00.750
02.24.015 - temp starts falling down - run out of LN2
02.47.218 - temp falling down -
03.10.656 - temp falling down - Last drops of LN2
03.33.922 - temp falling down - it has reached -124*C and falling
- - - - - - - rig freazes - temp at -118*C - NO MORE LN2 to feed it....

BUT I'll be back tomorrow....Don't ask about 32M frequency.....;) :D
12-13-2006, 08:51 AM
TaPaKaH

Quote:

Originally Posted by hipro5

00.06.531
00.26.828
00.50.453
01.13.984
01.37.375
02.00.750
02.24.015 - temp starts falling down - run out of LN2
02.47.218 - temp falling down -
03.10.656 - temp falling down - Last drops of LN2
03.33.922 - temp falling down - it has reached -124*C and falling

still slower than WR :D
http://www.ocxtreme.org/onepagebook/...832mwrwinc.jpg

Show 100 post(s) from this thread on one page

All times are GMT -8. The time now is 06:21 AM.

XtremeSystems