Team Group Setup details on DFI NF4/CFX3200DR thread

Printable View

04-29-2006, 06:53 PM
Onepagebook

Team Group Setup details on DFI NF4/CFX3200DR thread

**reference cpu is Opteron 154 aircooling
PSU: PC P&C 1000w

Bh5 First:

FSB Bus Frequency: 250
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 12
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 3.26v(real vdimm is about 3.2v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):2
tRCP:2
tRAS:5
tRP: 2
tRC: 7
tRFC:12
tRRD:2
tRW:2
tRTW:2
tWTR:1
tREF: 3120 or (4708 , 3684 for long time bench like super pi 32m)
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct: disable

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 3 (4 works perfectly as well) or try 5 as well
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 300
Max Async Latency: 7ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4

************************************************** *******************************

TCCD...weird, my TCCD used to go very well on all NF4 board with 2.5-3-3-6 setting over 300mhz 1:1
However, no matter what, just can't get it running @ this board, but here is a solution, thanks the ODD
I can run 335 fsb with ODD so I can have like 301mhz on ram though.

Team Group pc4800

FSB Bus Frequency: 335 (so it will be 300 on the ram)
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 9
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 2.67v(real vdimm is about 2.72v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):2.5
tRCP:3
tRAS:5 or 6
tRP: 3
tRC: 7
tRFC:14
tRRD:2
tRW:2
tRTW:2
tWTR:1
tREF: 3120 or (4708 , 3684 for long time bench like super pi 32m)
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct: Enable

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 3
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 450 or 600
Max Async Latency: 8ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4

************************************************** ********************************

Team Group UCCC:

FSB Bus Frequency: 280
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 11
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 2.63v(real vdimm is about 2.67v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):3
tRCP:4
tRAS:6~8
tRP: 4 (some UCCC will do 3 especially 0552 dated)
tRC: 7
tRFC:14
tRRD:2
tRW:2
tRTW:3
tWTR:2
tREF: 3120 or (4708 , 3684 for long time bench like super pi 32m)
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct: Disable

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 5 (think about 7;))
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 300
Max Async Latency: 8ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4

************************************************** ************************************

Team Group Micron 5bf:

FSB Bus Frequency: 275
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 11
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 2.70v(real vdimm is about 2.74v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):3
tRCP:3
tRAS:6~8
tRP: 3
tRC: 7
tRFC:14
tRRD:2
tRW:2
tRTW:2 or 3
tWTR:2
tREF: 3120 or 4708 , 3684 for long time bench like super pi 32m
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct: Disable

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 3 or 5
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 300 or 450
Max Async Latency: 8ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4

************************************************** ************************************

Team Group I/A series:

FSB Bus Frequency: 280
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 11
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 2.63v(real vdimm is about 2.67v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):3
tRCP:3
tRAS:6~8
tRP: 2
tRC: 7
tRFC:14
tRRD:2
tRW:2
tRTW:2
tWTR:2
tREF: 3120 or 4708 , 3684 for long time bench like super pi 32m
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct: Disable

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 4 or 6
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 450
Max Async Latency: 8ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4

************************************************** **********************************************

I will contune to update about all those settings.

OPB
05-10-2006, 01:39 PM
wrc06

I've been trying to break 310HTT 2.5 4 4 8 with the Xtreem DDR600 TCCD without any luck. Hoping to get some help when you get the chance to test the cfx3200 set together. :)
05-12-2006, 02:40 AM
wrc06

edited: not stable at originally posted timings
05-19-2006, 06:23 PM
Onepagebook

ok, I also have same problem from TCCD..I can't do 1:1 over 300 htt witn 2.5-3-3-x timing no matter what, (same settings can easaily reach pretty high on my UCCC except CL=3. However, if I use divider or ODD, then I can do 2.5-3-3-x. Below is my setting running memory frequency@ 300,

FSB Bus Frequency: 335
LDT/FSB Frequency Ratio: 4x
CPU/FSB Frequency Ratio: 10
RD580 HT PLL Speed: hight
HT Bus NMOS Drive Strength: 31
HT Bus PMOS Drive Strength: 31
HT Bus Receiver Impendence: 31 or 5~10
CPU HT Bus Drive Strength: Strong
K8 Cool & Quiet Support: none

CPU VID Control: 1.4
CPU VID Special Control: auto
DRAM Voltage Control: 2.67v(real vdimm is about 2.72v)
SB PCIE Voltage: 1.8v
NB Analogue Voltage:1.21v
LDT Bus Voltage:1.21v
NB Core Voltage:1.21v

DRAM Frequency Set: 200mhz, 1:1
CPC: enable or auto
CAS (tCL):2.5
tRCP:3
tRAS:5 or 6
tRP: 3
tRC: 7
tRFC:13
tRRD:2
tRW:2
tRTW:2
tWTR:1
tREF: 3120 or 4708 , 3684 for long time bench like super pi 32m
Bank Interleaved: enable
Errata 94: Disabled
Errata 123: AUTO or disable
Odd Divisor Correct:

DQS Skew Control:0
DQS Skew Value: none
DRAM Drive Strength: 3
DRAM Data Drive Strength: 2 or auto
DIMM 1/2 Clock Timing Skew: auto
DIMM 3/4 Clock Timing Skew: delay 300
Max Async Latency: 8ns
Read Preamble Time:5ns
IdleCycle Limit: 16clks
Dynamic Counter: Enable
R/W Queue Bypass: 16x
Bypass Max: 7x
Burst Length: 4
05-20-2006, 11:14 AM
wrc06

I've been trying to run superpi 32m, sp2004 blend test, and 10 loops of 3dmark01 all at the same time to test stability. So far, I've pass the duration of 3dmark01 (@ 40 minutes) 1 time. I was sloppy and didn't write the timings down and haven't been able to complete any tests. Still trying though.
05-20-2006, 10:30 PM
Onepagebook

Update Team Group Xtreem series DDRI settings information,
please check the 1st post out. THanks

OPB
05-21-2006, 12:36 PM
wrc06

Running superpi 32m, sp2004 blend, and 3dmark01 all at the same time is not a good test. sp2004 doesn't get to run while superpi is going and the system doesn't get stressed. I'm now trying sp2004 alone at 300HTT and it has constantly failed with different memory settings. Still working at it.

I've heard that this set does about 315HTT 2.5 4 4 8. I really this a decent bios is absolutely needed. Come on, DFI !!
05-24-2006, 05:10 AM
wrc06

I'm at a loss on making this board run sp2004 stable. I've tried looser timings to the above and the system is still not stable. Don't know how much longer I'm willling to wait for DFI to release a stable bios before sending this mb back for a refund.
05-31-2006, 05:40 PM
wrc06

Studid question, but OPB would you happen to know relative SAFE max volts for this Apollo DDR600 1Gb set? I've not gone over 2.83 (2.91 bios reading) on short testing. Is this ok?
05-31-2006, 07:37 PM
Onepagebook

Quote:

Originally Posted by wrc06

Studid question, but OPB would you happen to know relative SAFE max volts for this Apollo DDR600 1Gb set? I've not gone over 2.83 (2.91 bios reading) on short testing. Is this ok?

Most likely I would say that it really depends on the memory itself,let's say :

if you have the set before year 2005, then you 'd better not get it over 2.95or so.

if you have the set after year 2005, then you 'd better not get it over 2.85v~2.90v or so.
06-02-2006, 01:57 AM
wrc06

Thanks, OPB. They are the set after 2005.

I have no idea what is going on now. Windows will either reboot or lockup in 2-5 minutes. This might be due to a change in cpu. I've got another processor on the way and I'm hoping the issues I've been having will disappear.
06-08-2006, 08:59 AM
sway

excuse me but, can anyone tell me if the BH-5 PC3200 are likely to Overclock less than the PC4000 version, or buying the PC4000 its just an insurance that they will do 250Mhz?

logic tells me that PC4000 its the wise choice, but enlight me anyway!

thanks!
06-09-2006, 04:29 AM
Lane-k

I will have soon the CFX3200, what bios use with this one and the BH5 zeus PC4000?
06-20-2006, 10:03 PM
Xtreem Tech

0417 or 0425 would be nice
07-03-2006, 01:41 PM
wrc06

I got rid of the CFX3200 and moved to NF4 Ultra-D. Not too sure why it won't run anything. I had (2) opty 146 and (1) opty 165 that was no where near stable. I've waited for 2 months and no new bios surfaced. So much for the hype......

The opty 165 now runs 2.790 @ 1.425v and memory htt310 2.5 5 5 10 1T 2.89v (bios) prime stable. Whew!....took some time to get to this point....
07-03-2006, 02:50 PM
sofarfrome

dumb question?

what is ODD???
07-04-2006, 12:36 AM
Xtreem Tech

ODD means when CPU FSB reach 300MHZ or above if turn it on the DRAM:FSB would auto change 9:10 NOT 1:1.

If odd open the performance would become lower.

regards.
08-05-2006, 10:55 AM
cmay119

OPB or Xtreem Tech, would you guys be willing to give me some good recommended timings for DDR500 with the I/A sticks? I've got my CPU @ 2500MHz (250x10) right now, and I'm not willing to take it further until I get some better cooling. Quite a few things in the BIOS are still set @ auto. I'm willing to tweak, but it would be nice to have some settings to start from before I go all out. Thanks all. :)