Hello
I want to mod my card, but i don;t know why. I tried bioses from gigabyte and eVGA but voltage and overclockability was the same. Can anybody help ? :)
My GPU and memory :
http://img453.imageshack.us/img453/4687/image16rr.jpg
Printable View
Hello
I want to mod my card, but i don;t know why. I tried bioses from gigabyte and eVGA but voltage and overclockability was the same. Can anybody help ? :)
My GPU and memory :
http://img453.imageshack.us/img453/4687/image16rr.jpg
Please take a picture of these two spots.
Attachment 46057
Then we can help you more!
Ok i got it :)
Click for full size image
http://img48.imageshack.us/img48/565...nek27xt.th.jpg
If you have multimeter you should measure resistance from pin 4. And if you could post larger picture of this area, we will know where you should solder resistor.
Attachment 46062
Where put on the multimeter cables? Ono to pin 4 , second to ????
Image
http://img422.imageshack.us/img422/3...age46sb.th.jpg
...on the ground. How experienced you are with voltage mods? Have you done it before?
What is your max clocks now? Do you know the Vcore in 3D mode?
Experimence - 3 volltmods : FX5200, FX5900 and GF6200
My default Vcore is 1,05V - need at least 1,2 - 1,3 V like on 7600GT :)
Now max GPU is only 450 - I want at least 600
Ok. Could you try this?
Attachment 46075
Tell me if it works. It should!
ok i will try :)
Ya, but where to measure Vcore? :( I told that it's 1,05V but in bios VID table. I don't know where is measuring point :( Sry for my lame
hmmm.. Check these points.
Attachment 46078
Thanks it's 1,04V and it's very possible :)
I'm waiting results :)
Does it work？
Could you post the moded picture and oc result？
thx~ :)
I posted my results with the volt mod using the pencil trick on another forum, including photos and graphs as well. The 7600GS appear to overclock fairly well at 600/485 at 1.32V.
http://forums.guru3d.com/showthread.php?t=180831
Thank you SF3D. I used your tips as a starting point.
Best regards,
Anthony Rogers
PentiumD 805@3.4~1.3V/Big Typhoon
Leadtek7600GS@600/485~1.32V/VF700Cu
Gigabyte GA-8N-SLI
2x1Gb GSkill DDR2 @ 680 4-4-4-12
Antec Sonata II
2 x 160Gb Seagate 7200.7 Raid 0
400Gb Seagate 7200.7
2 x Syba PCI ATA Raid
BenQ DW1655
Welcome Anthony Rogers!!!
Could you post your results here also. I can't view them in your link. I'm interested to get one of these budget cards too.
Thank you!Quote:
Originally Posted by SF3D
I'd hate to double post on two forums, but I'll post the 3dMark06 plot and the table here also. I've moved the images to imageshack hosting, so maybe that work be better.Quote:
Originally Posted by SF3D
Since I've had so much luck overclocking the Leadtek card, I'm thinking about getting another to run in SLI, before they start changing the revision or chips used, etc. I'm also planning on making a simple circuit with a switch so that I can switch the mod on and off for both cards.
Best regards,
Anthony Rogers
Excerpted from post at Guru3D
http://forums.guru3d.com/showthread.php?t=180831
3DMark06 Plot
http://img99.imageshack.us/img99/902/plot8rx.th.gif
Clock Frequencies and Temperature Table
http://img100.imageshack.us/img100/7842/table8wt.th.gif
It appears that the active HSF does a fairly good job of cooling even when overclocked, as compared to the passive HS from other reviews at Newegg and below at HardwareZone. The HSF is also fairly quiet and not audible above the other fans in the PSU, Big Typhoon, and 120mm case fan
http://www.hardwarezone.com/articles...856&cid=3&pg=9
THis is just VGPU mod rite? is there a VMEM mod? Anthony have you done both mods because your memory is running over a gig in your other post, and that seems quite high.
Yes, you are absolutely correct that it's too high. I have since corrected the post. Thank you for pointing out my typo.Quote:
Originally Posted by Inteleron
The maximum memory clock that I could achieve was 970 (or 485 in coolbits).
All further replies should be directed towards the thread in at Guru3D to consolidate the discussion.
http://forums.guru3d.com/showthread.php?p=1733608
Best regards,
Anthony Rogers.
To ALL
Read and See All Volt_mod on referens: http://people.overclockers.ru/nforser/record5
THat site is in Russian...LOL! Also the PCB is blue which reminds me of the non-reference PCB Galaxy version volt mod already featured here. If this is true the above site is no help.
Thanks Anthony! That 7600GS pencil mod works with my 7300 GT :banana:
That's reference Albatron 7600GS.Quote:
Also the PCB is blue which reminds me of the non-reference PCB Galaxy version volt mod already featured here. If this is true the above site is no help.
yes, and that is american :DQuote:
THat site is in Russian...LOL!