Finally Lain-Li V2000 prototype is complete (well kind of)

If you remember what I went through before, this is upgraded version of previous prototype. I am still waiting for my condenser and compressor for finilizing the design so using old mach II condenser and compressor with newer revision of chilly1 evap is utilized. Froster-X is there but it isn't installed yet as I am waiting for AC adapter for it. BTW, Thanks for the sidewindow NJKid32 :) (I just borrowed it lol getting one myself next time I drop by my supplier)

http://webpages.charter.net/jinwpark...to.2.Front.JPG

Froster-X LCD... will replace picture when I get froster running.

http://webpages.charter.net/jinwpark....Back.Temp.JPG

PSU was meant to be sitting at bottom but I couldn't get extra length for few cables on this full sized case. Will have to look into extenders. Pointers are welcome. (especially PCI-e extender)
Bottom is NJKid32's case that has proper orientation to allow best airflow.

http://webpages.charter.net/jinwpark...oto.2.Back.JPG

http://webpages.charter.net/jinwpark...oto.2.Side.JPG
I love this stock window that is made by lian-li. Very clean.

http://webpages.charter.net/jinwpark....SideNaked.JPG
Innard of system.

http://webpages.charter.net/jinwpark...o.2.Inside.JPG
Before putting into case and load testing tuning.

http://webpages.charter.net/jinwpark...2.IdleTemp.JPG
As usual, X2 running 1.7-1.71v 3.1ghz 2xballistix, etc. Like Idle temp? :)

http://webpages.charter.net/jinwpark....DualPrime.JPG
Again, same setting running dual prime :)

Unfortunately, these wonderful temp is not same inside case. #1. evaporator lost bit of efficiency leaning sideway, #2. Case airflow is still bit less than ideal. I would need to use something stronger than Panaflo M1A to really get back the temperature. However, I chose not to as being silent and cool is what I am aiming for. Total temperature lost is about 3-4c whic is more than acceptable as even with the temperature increase, it is well over 10c colder than stock vapochill LS :)

Once new compressor, condenser, misc parts I asked lian-li to make arrives, I will get next revision of prototype up :)

I'm impressed :D You did a sweet job bro. :woot:

nice job, time for my v2000 :p:

Wow thats really nice. Now I know who to call if I want to buy a V-2000 wink wink

you may have all that, but your computer may still be at risk, so watch out! (*points at lower right corner of the screen*)

That's looks REALLY cool man. If I had the money and the knowledge for this, I'd be all over it

nice case

Thanks guys :) The warning is on my load testing hdd that has no network to begin with... :) Got AC adapter today so I will post G-froster in and clean up the wire somewhat more tomorrow :)

Hey, nice system jinu. I've been thinking about doing the same ever since I saw your first attempt and was wondering if there is any chance in fitting a PSU in the case? Could you possibly give me the dimensions for the bottom compartment? Cheers

nice temps jinu!

Thanks again guys. I built one more unit like this today (well just innards so far... case installation comes tomorrow after it passes leak testing).
Probably will put froster value on that one.
Anyways, I got froxter-x running :P It's really cool when you get exact same reading (+/- 1c) of UEI DT200... Only place where delta was higher was around start up where it showed +/- 2c which I could really care less :P
One thing was... wiring this thing was... painful. I hope to see XE version soon. No more X for me on my units I think.

http://webpages.charter.net/jinwpark...o.2.Froste.JPG
http://webpages.charter.net/jinwpark...B/FrosterX.JPG

Sorry for the blurry picture. Night time shooting with flashes on this snap shooter doesn't work to well :P Anxiously waiting for my Canon to arrive hehe.

Nice work Jin! I would buy one in a second if I didn't know how to build my own phase change :p:

Bet that 2nd unit'd fetch a pretty penny on eBay