FX Meets DI - First Run

Printable View

Show 100 post(s) from this thread on one page

10-07-2005, 10:37 AM
babyelf

FX Meets DI - First Run

DFI NF4 Ultra-D
FX57 CABCE 0516 WPMW
Antec 550W TruePower2.0
2 x Raptors
Corsair 3200LLv1.1 | OCZ GX | TEAM BH-5
Chilly1 DI Container
Liquid Electrical Tape
Acetone
Funnel
Neoprene Tape

http://www.mini-itx.com.au/Images/DryIce/TheStuffs2.JPG
http://www.mini-itx.com.au/Images/Dr...prene-Tape.JPG
http://www.mini-itx.com.au/Images/DryIce/DryIce-1.JPG

Insulation : (listed by steps)

Liquid Electrical Tape around socket
- Liquid Electrical Tape will take approximately 20-30minutes to dry depending on how thick you apply on the motherboard. It will peel off easily from your motherboard so don't worry.

http://www.mini-itx.com.au/Images/DryIce/LET-Front.JPG
http://www.mini-itx.com.au/Images/DryIce/LET-Back.JPG

Neoprene Tape on Liquid Electrical Tape and gaps taped up with electrical tape and holes covered by Liquid Electrical Tape
- Next use some neoprene tape on the liquid electrical tape for extra insulation and for the extra height for better contact with the cylinder neoprene piece.
- Tape some neoprene on the back as well just in case.
- Cover the gaps with electrical tape

http://www.mini-itx.com.au/Images/Dr...late-front.JPG
http://www.mini-itx.com.au/Images/Dr...ulate-back.JPG
http://www.mini-itx.com.au/Images/Dr...Insulation.JPG

Test Mount

http://www.mini-itx.com.au/Images/Dr...-Run-Mount.JPG
http://www.mini-itx.com.au/Images/Dr...un-Mount-1.JPG

Dry Ice Run
- Best run for me is about 50ml of Acetone then some crushed ice followed by normal dry ice pieces.

http://www.mini-itx.com.au/Images/DryIce/Running-1.JPG
http://www.mini-itx.com.au/Images/DryIce/Running-7.JPG
http://www.mini-itx.com.au/Images/DryIce/Running-2.JPG

1M
http://www.mini-itx.com.au/Images/DryIce/1M-22.766.JPG

8M
http://www.mini-itx.com.au/Images/Dr...-4m15.750s.JPG

32M
http://www.mini-itx.com.au/Images/Dr...20m32.078s.JPG

After Run
- What I do is i remove all cylinder neoprene and then pour out all dry ice from the container.
- After that I add water into the container to warm the container so that the bond between the container and processor will loosen and then give it a good twist and it will come off easily.

http://www.mini-itx.com.au/Images/Dr...y1-on-FX-3.JPG
http://www.mini-itx.com.au/Images/Dr...y1-on-FX-2.JPG
http://www.mini-itx.com.au/Images/Dr...lly1-on-FX.JPG
http://www.mini-itx.com.au/Images/Dr...lly1-Frost.JPG

I have about half an eski of DI left.. will be doing more benching again tomorrow :toast:

2nd day :

first bad mount and ran out of ceramique.. tried AS5 and it didn't work well so had to cancel subsequent runs

had some dry ice left so i had some fun with them :p:
http://www.mini-itx.com.au/Images/Dr...ts-Water-2.JPG

Removing Insulation
http://www.mini-itx.com.au/Images/DryIce/LET-Peel-1.JPG

http://www.mini-itx.com.au/Images/DryIce/LET-Peel-2.JPG
10-07-2005, 10:50 AM
bachus_anonym

Nice 32M time, babyelf :up: Don't forget to submit it on Holicho's Ranking ;)

Gotta love that liquid electrical tape, eh? :) That stuff is just a must-have for phase change and DI/LN2 runs...

Congrats on a successful session :toast:
10-07-2005, 10:52 AM
Athens[2004]

Nice !! Very Nice insulation & pretty Good Benches 2
10-07-2005, 11:09 AM
babyelf

Quote:

Originally Posted by bachus_anonym

Nice 32M time, babyelf :up: Don't forget to submit it on Holicho's Ranking ;)

Gotta love that liquid electrical tape, eh? :) That stuff is just a must-have for phase change and DI/LN2 runs...

Congrats on a successful session :toast:

thanks alot :D

one more session to go tomorrow :D

yea lol.. started using it then i couldn't stop lol.. just had to brush it everywhere

Quote:

Originally Posted by Athens[2004

]Nice !! Very Nice insulation & pretty Good Benches 2

thanks :D
10-07-2005, 11:13 AM
waddupmm

Pics dont work any more?
10-07-2005, 11:25 AM
babyelf

just refresh a couple of times.. hosting went a bit crazy today
10-07-2005, 11:43 AM
babyelf

3602.5Mhz

257.3 x 14 :)
10-07-2005, 12:06 PM
metro.cl

nice runs and nice insulation
10-07-2005, 06:10 PM
babyelf

Quote:

Originally Posted by MickeyMouse

yeah got pics working now nice runs M8 :)

thanks MM :)

Quote:

Originally Posted by metro.cl

nice runs and nice insulation

thanks :D

One Q before i start today tho.. how much Acetone is needed in the container?

After running for a while the temps went back up to 0c or so in bios so i took it apart and there's no condensation.. then i checked and realised there's no more acetone left..
10-07-2005, 09:29 PM
afireinside

Not sure about the chilly1 container but a shot glass works best. I've seen using a medicine cup filled to the top lately. I doubt thats enough for the chilly1 tube, though.
10-07-2005, 10:44 PM
babyelf

ic.. thanks for the tips.. going to start now.. will try pouring about 50ml first and see how the temps go

:D
10-08-2005, 12:51 AM
babyelf

first mount bad... then tried to remount but ran out of ceramique so i tried AS5.. and temps were horrible..

so much for benching today.. :(
10-08-2005, 07:58 AM
T_M

no pics for me :(
find another host maybe
10-08-2005, 08:19 AM
[XC] moddolicous

I think people use AS Ceramique for subzero benches, not AS5. Looks really good.
Some timings to try for SPI 1m:
Tref: either 4708 or 3684
tras: 3
TRC: 5
Async latency: 7ns
read preamble: 5.5 or 5ns
10-08-2005, 08:25 AM
\Karting_freak

impressive!
10-08-2005, 12:49 PM
kiwi

Yeah, I like that neat insulation as well and nice scores :toast:
Does that Liquid Electrical Tape come off easily or not?
10-08-2005, 07:50 PM
babyelf

Quote:

Originally Posted by T_M

no pics for me :(
find another host maybe

yea looking for one at the moment :)

Quote:

Originally Posted by moddolicous

I think people use AS Ceramique for subzero benches, not AS5. Looks really good.
Some timings to try for SPI 1m:
Tref: either 4708 or 3864
tras: 3
TRC: 5
Async latency: 7ns
read preamble: 5.5 or 5ns

yea.. ran out of it that's y 2nd day didn't go well..

thanks for the tips.. ceramique coming soon and might find another day to do it

Quote:

Originally Posted by \carting_freak

impressive!

thanks :D

Quote:

Originally Posted by kiwi

Yeah, I like that neat insulation as well and nice scores :toast:
Does that Liquid Electrical Tape come off easily or not?

pics coming under next reply :)
10-08-2005, 07:54 PM
babyelf

http://www.mini-itx.com.au/Images/DryIce/LET-Peel-1.JPG

had some DI left after that.. so was playing with it lol

http://www.mini-itx.com.au/Images/Dr...ts-Water-2.JPG
10-09-2005, 02:59 AM
dinos22

holy :banana::banana::banana::banana: baby:banana::banana::banana::banana::banana: you're are killing it over there.....extremely nice 32M speeds.......man with some more tweaking OPB watch out
10-09-2005, 07:43 PM
babyelf

ta dinos.. OPB is called OPB for a reason u know? ;)
10-09-2005, 07:58 PM
dinos22

Quote:

Originally Posted by babyelf

ta dinos.. OPB is called OPB for a reason u know? ;)

hold no prisoners....there was someone there before OPB too......this is XS afterall......hehehhe

good luck anyways...looking good
10-09-2005, 09:20 PM
SLi_dog

Hi babyelf,
Nice setup and PI times. :toast:
How much did the Chilly1 DI/LN2 tube cost?
10-10-2005, 12:18 AM
babyelf

ta

got it on for sale here.. pm chilly1 for the price of the new container :)
10-10-2005, 12:38 AM
nachthymnen

Incredible!!!You have obtained exactly my same time in 1M: :D
http://img407.imageshack.us/img407/4...27663lk.th.jpg
10-10-2005, 12:47 AM
babyelf

Quote:

Originally Posted by nachthymnen

Incredible!!!You have obtained exactly my same time in 1M: :D
http://img407.imageshack.us/img407/4...27663lk.th.jpg

lol nice lol

on DI too?

Show 100 post(s) from this thread on one page