3000+ Venice: 3194MHz Pifast || Budget ocing!

Done on custom phase-change :)

http://valid.x86-secret.com/show_oc?id=19647

http://members.home.nl/epsilon/19647.png


http://members.home.nl/epsilon/temp/...3194_3836s.JPG

On this single stage home made phase change :)
http://members.home.nl/epsilon/phase...hmarking03.jpg


Score on boxed air:
http://members.home.nl/epsilon/temp/...2845_4239s.JPG


max screenshot : around 3300mhz, will post tomorrow.

Need a new install, the NF4 drivers arent installed yet, only NF3 drivers. Will gain another 0.4sec or something :)

Other specs:

- DFI NF4 Ultra-D
- 2x256MB Mushkin old bh-5 (level2)
- PCP&C 510w sli psu
- 120GB WD 7200RPM (like it matters)
- FX5200 PCI

Very nice! What was the evap temp at CPU idle ?

Nice oc epsilon.! :toast:

What about the week and stepp??

Awesome result :toast:

And yeah, we want to know step and week :D

Quote:

---

Originally Posted by Micutzu

Very nice! What was the evap temp at CPU idle ?

---

The evap temp (on the block) varied from -48c to -38 (depending on speed and voltage) :D.

That's in the very bottom of the block, so infact the CPU temp. -22c in bios btw ;).

Stepping:

CBBLE 0512 DPBW
xxxx0217

:)

awesome result :D

budgetoverclocking is cool :banana:

is just like the winnie's but these are even better :woot:

nice, what are your temps

Maybe I will suicide shot today :)

Temps in the bottom of the evap vary from -48c idle @ 2800mhz 1.4v to -38c idle @ 3194 1.7v. Loaded the temps rise to -30c in the bottom of the evap block.

The sensor is here:
http://members.home.nl/epsilon/phasechange_2/evap09.jpg

And not on the suction as the Mach2 GT etc. The loaded temps at 3194/1.7v are -42c on the suction line :)

And a suicide screenshot @ 3419mhz

http://valid.x86-secret.com/show_oc?id=19647

http://members.home.nl/epsilon/19647.png

quality graphics card! That is PCI i take it? What is it?

Very good speeds btw, maybe a bit of burn in will help it go even higher? How long have you had it for?

It is brand new, this is after just 5hours of running both air and phase-change :)

It is FX5200 128MB PCI videocard
I use it for CPU benches because it practically doesn't take power so CPU has all :)

well a bit or burn in probably won't hurt then, i know it's physically incorrect at all, but it does seem to work, loads of people have noticed it.

just wait and the CPU will go faster probably :D

CPU will be sold

THis is the final result:
http://members.home.nl/epsilon/temp/...3194_3750s.jpg :)

Wow ! Nice score Epsilon :toast: ...


Please write more informations about Phase-change- what compressor, what gas :rolleyes: ???

peter

Isnt that a WR? If it's post it in the WR thread.

Great job and great CPU :toast:

nice

which step?

I receive my 0517 DPMW wednesday :)


coolaler can bench at 3.41G with his 3000+

lol, phase change isn't budget OCing :(

GJ tho :)

Quote:

---

Originally Posted by Shadowmage

lol, phase change isn't budget OCing :(

GJ tho :)

---

Its "custom phase-change" which means the whole thing probably didn't cost more than $500, not exactly budget, but not exactly the high price you think of for phase change cooling

Nice scores. I think with some tweaking and a little higher OC, 36sec in PIfast would have been possible.

maybe it was possible, but I have to lap my evap first, contact wasn't 100%.

The thread of my cooling systems is over @ teampuss

Here is the thread:
http://www.teampuss.com/forums/viewtopic.php?t=605

But, because you have to register to view, I will post some specs here :)

It's a 14cc 1/2hp R404a compressor
runs with 3meter 0.031" captube
Propane as refridgerant
and chilly1 evap :)

idle @ -57c
Loaded with 180w @ -42c on the suction line (were prommy's are meassured)
-30c in the very bottom of the block @ load.

HOLY SH*T! :slobber: :banana:
I don't know what to say.....

AWESOME RESULTS Epsilon! :D :D

Nice setup you got there ! congrats ! How did your Venice do on air maybe with a better week you could go higher.