3.4vdimm / 1T cmd. see sig for testbed. memtest 100% stable. 1x512 only
not bad for $220
http://xtremesystems.org/forums/atta...chmentid=19631
Printable View
3.4vdimm / 1T cmd. see sig for testbed. memtest 100% stable. 1x512 only
not bad for $220
http://xtremesystems.org/forums/atta...chmentid=19631
niceee :) i just ordered 512 of this pdp xbl @ newegg :) hope i can get these results
wow thats very nice :D
for the PDP's i almost always hear that they have the voltage loving TCCD ic's
if you can get 2 sticks like that it would be awesome.
i wonder how it would run in dual channel
Geez. You've got PDP memory, too? You sure have a lot of memory modules, bro.
Best I could do at 2-2-2 was 230mhz @3.4v 2x512. I tried the other stick and it also does 600mhz. I really need a dual channel board. I think a FX55 could really do some damage with these. :)
very nice, i keep going back and forth between pdp or the ocz plat rev 2. I wish i could give both a shot but i'd rather not spend the extra money.
is that 3.4V with ddrbooster or vdd mod?
4.v modded dfi bios with a 3.3 adjustable pot on the ocz powerstream 520.Quote:
Originally Posted by Skip
Thats sweet. That DFI board is awesome. I wanna see how their SLI board will be, as that will be when i purchase my new memory.
You have trc at 17, what do you use for value for the settings below that one in bios ?
Need some idea cuz i never got mine to reach 300 with those timings.
Can you write down some settings ?
3.4v is that safe for 24/7 usage?
I played with the trc in clockgen later. I ran some quick tests but no improvements in superpi. I just had did 2.5-3-3-7 cpc enabled, drive strength level 2. everything else on auto. Now the question is wait for nf4 and sell my agp card, or buy a nf3 939 rig. MSI or get another gigabyte Ultra nf3 and a ddr booster and hope I get a Leprechaun inside the cpu box.Quote:
Originally Posted by Ubermann
should i order it or not ?
Nice OC. :toast:
Been trying to decide which set to get. - G.skill, OCZ, or PDP.
Need the voltage loving TCCD ic's for this nf2 board. Might be putting my Bh-5 up for sale soon if they perform well. :D
After a breaking in period i can confirm that Patriot XBL indeed likes volts. Mine doesnt like any less than 2.85 now @ cas 2 2 2 7
i just ordered the pc3200 2x256 kit for 107 bucks at the egg. i hope these thing oc nice.. stay tunned.
peace perc,
Susquehannock , your sig is TOO BIG!
any "Patriot XBL" seller in europe?
OMG, you need 3,4V on to get 300MHz?
My OCZ does 310MHz errorfree in memtest with just 2.8V ans 313MHz with 2.9V
Kakaroto's Gskill only needs 2.7V for 310MHz.
All TCCD. Did you try lower?
Too big how? :confused:Quote:
Originally Posted by enzoR
Is trans am's too big also? It looks to be about the same size. Well, my fonts are bigger. ;)
Sus your already running 240 FSB with 2 2 2 timings why the heck you wanna get TCCD ram for?
Good for you and Kakarotos Gskill, but not all tccd is going to run that high at low volts.Quote:
Originally Posted by Zeus
I did try lower but got errors. These are much better with high volts. These are week 40. same week as my el4200 platinum. My ocz likes high volts as well.
How high can the 3.3 go on that PowerStream Trans?
Nice results :toast:
3.74 / pot turned all the way.Quote:
Originally Posted by G H Z