Project MonoBits

Hello everyone!

Now it's time for me to finally start another project!
I got the idea when I saw a preview image that BitFenix ​​had posted on their Facebook page and I was instantly in love with the case, I thought to my self that I really wanted that case and hopefully do a buildlog from it. I immediately started talking to people on various forums and websites, but also some who posted reviews on Youtube and asked about different dimensions so I could start sketching how I would like to have the build. My goals are extraordinary and should strive to do the best Prodigybuild made so far. I will go with a full setup of watercooling into this project, i will try to make it as highend as i can make it, everything that can be watercooled in this build will be. I will build and mod everything to perfection and having fun throughout the whole project. It will normally include a lot of sleeving and lots of other things and I will keep the project relatively short so it will hopefully be updated at least once or twice a week. That was it for the little speech, and here comes the additional information on the project, I hope you think this is interesting and I wish you pleasant reading!
:banana::banana:

Hardware:
Case: BitFenix ​​Prodigy White
Power Supply: Silverstone Straider Plus 850w
Motherboard: Zotac Z68-ITX WiFi
processor: Inter Sandy Bridge 2500K
Memory: Corsair Dominator GT 2000MHz
Graphics Card: Asus GTX570 Direct CU II
SSD: 2x 120GB Corsair Neutron GTX

Watercooling
Fans: Corsair Air Series SP120 High Performance Edition High Static Pressure 120mm Fan
Controller: mCubed T-balancer MiniNG
Radiators: 1x Alphacool NexXxoS ST30 Full Copper 120mm, 2x Alphacool NexXxoS ST30 Full Copper 240mm
CPU-Block: Bitspower CPU Block Summit EF (Intel) (Acrylic Top Version)
RAM-Block: Bitspower Galaxy Freezer 2
GPU-Block:
Reservoir: Single D5 Top Upgrade Kit 150 (Black POM Cap) (Model Name: BP-D5TOPUK150P-BKBKCL)
Pump: Alphacool VPP655 - Single Edition
PumpTop: D5 MOD TOP V2 (POM Version) + D5/MCP655 MOD KIT (Model Name: BP-655D5P2-MBK)
Tube: Primochill 7/16"ID, 5/8"OD Clear
Fittings & Acessories: Bitspower
22x G1/4" Bronze Age Compression Fitting CC6 For ID 7/16" OD 5/8" Tube (Model Name: BP-BACPF-CC6)
10x G1/4" Bronze Age Rotary 45-Degree IG1/4" Extender (Model Name: BP-BA45R)
10x G1/4" Bronze Age Rotary 90-Degree IG1/4" Extender (Model Name: BP-BA90R)
2x G1/4" Bronze Age Triple Rotary 90-Degree IG1/4" Extender (Model Name: BP-BA90R3D)
8x G1/4" Bronze Age Stop Fitting (Model Name: BP-BAWP-C06)
2x G1/4" Matt Black CaseTop Water-Fill SET (Model Name: BP-MBWP-C04)
4x Thermal Pad A (94x19x0.5MM) (Model Name: BP-WBTP-A)
1x Matt Black Mini Valve With Black Handle (Model Name: BP-MVV-MBKBK)
1x Bitspower Flow Indicator (Model Name: BP-FI-CLBKMBK)


MonoBits is sponsored by:
Aqua Tuning
Bits Power
BitFenix
Cooling Tough
Corsair
Silverstone

Please visit and Like my Facebook Page and you will see my news, sneakpeaks, buildlogs, sleeving and much more!

Here are the Scetchups, Yes i know...The case hase some improvements today from what i did in the sketchupmodel, i hope you like it so far !

http://i267.photobucket.com/albums/i...t/fca6aa10.jpg

http://i267.photobucket.com/albums/i...t/c271af05.jpg

http://i267.photobucket.com/albums/i...t/56a1f00e.jpg

http://i267.photobucket.com/albums/i...t/199cca39.jpg

http://i267.photobucket.com/albums/i...t/0895531f.jpg

http://i267.photobucket.com/albums/i...t/926d9040.jpg

Looks good:up:

Why not put the 120mm rad in the rear 120 vent?

looking great!

tiny but mighty! :D

Quote:

---

Originally Posted by CrazyNutz

Looks good:up:

Why not put the 120mm rad in the rear 120 vent?

---

The 3D model was just temporarely, when i got the case yesterday i could mount the rad on the back, thet looks so much better :D!

Quote:

---

Originally Posted by jimba86

looking great!

tiny but mighty! :D

---

Ohh Yes!

your spending alot on the watercooling parts, why not go higher on the cpu/gpu?

Quote:

---

Originally Posted by Manicdan

your spending alot on the watercooling parts, why not go higher on the cpu/gpu?

---

The Cpu are perfect, why go with ivy bridge when sandy is better ?
The Gpu is enought for thi build actually, with a bit of overclocking it performs great!

Time for another update guys!
Today i bought the Bitfenix Prodigy, The white version because of the very clean looking front
Some pictures on the beauty

http://i267.photobucket.com/albums/i...a/6f5d415e.jpg

http://i267.photobucket.com/albums/i...a/5bccf71b.jpg

http://i267.photobucket.com/albums/i...a/8ecea868.jpg

http://i267.photobucket.com/albums/i...a/ce724237.jpg

http://i267.photobucket.com/albums/i...a/1e7228cc.jpg

The case was free from damages and artifacts etc and im glad about it, the swedish delivery firms are not that greatful with the stuff sometimes
Tomorrow i will take everything down for some prep work but more about that tomorow night as i am going to the workshop :)

Quote:

---

Originally Posted by Shurika

Yes! strip it! Love the design

---

Here it comes !

Hello Guys!
Today I had time to do a litel bit
I took down everything from the case, removed the hard drive cages, the 5.25 " bay and the fans, right now it's just the headchasis left and it will be modified a bit. I want to keep this build as clean as possible and I will not over do it somehow...designwise ;)
Here you have some pictures of the work so far.


The origginal inside of the case

http://i267.photobucket.com/albums/i...a/2832c662.jpg


I started removing the first harddrive cage which sat in place with a thumbscrew :)

http://i267.photobucket.com/albums/i...a/14b0160b.jpg


The next step was to remove the 240mm fanfilter on the top but also the front which went very fast and had just a simple locking mechaism and some clips, god its easy to work with the case!

http://i267.photobucket.com/albums/i...a/3bbf2466.jpg

http://i267.photobucket.com/albums/i...a/37459197.jpg


And now at last, the fans and the 5,25" Bay, everything i needed to do here was to remove some more screws and they were gone! I didnt need to use the dremel or my drill :)!
I will give my thumbs up for this awsome construktion, this is how it should be !

http://i267.photobucket.com/albums/i...a/89196f31.jpg

http://i267.photobucket.com/albums/i...a/76e139d3.jpg


An empty naked Prodigy, its some serious eyecandy!

http://i267.photobucket.com/albums/i...a/f4cab832.jpg


This was tonights update, i hope that my pacage from Aquatuning arrives tomorrow och the next day after.
More about that when it arrives and then i will be making another update,
Dont forget to comment and subscribe please :)
Se you until next time !

wow,this coming along great!

Quote:

---

Originally Posted by jimba86

wow,this coming along great!

---

Thank you jimba!

Halloj!
I received a rather unexpected package yesterday, and it was from Silverstone sponsoring me with a Straider 850w Plus (ST85F-P)
I thank awful lot for your help and the very quick delivery :)!

http://i267.photobucket.com/albums/i...a/ad0b10aa.jpg

http://i267.photobucket.com/albums/i...a/3e3de60b.jpg

http://i267.photobucket.com/albums/i...a/64f51170.jpg

http://i267.photobucket.com/albums/i...a/3a9595b1.jpg

http://i267.photobucket.com/albums/i...a/1f866475.jpg

http://i267.photobucket.com/albums/i...a/89aef5ce.jpg

What can I say about this PSU?
The power supply is very quiet, it has good efficiency and looks overall very good.
The only drawback is their multi-colored cables ...
There will be no problem for me in this case, because I will make my own from scratch instead, so I can get the right length and no hassles inside the case :)

It was the update for this time guys!
/ V.B

That's different, me likes !

Quote:

---

Originally Posted by SnW

That's different, me likes !

---

Great to hear my friend...

Hey everyone!
I now have an important package that helps me to see what happens with the water cooling inside the computer.
This package is from my good friend Andreas Walter who works over at Aquatuning :)
The content cinsists the latest full copper radiators from Alphacool who says to cool very well, regardless of their sizes, these radiators can also be found in brutal depths if you are the one who want the best of the best :)

http://i267.photobucket.com/albums/i...a/890a5a6d.gif

I thank Andreas a lot for his support in my project and that he kindly sponsored me with theese following items:
Alphacool VPP655 - single edition
Alphacool NexXxoS ST30 Full Copper 120mm
Alphacool NexXxoS ST30 Full Copper 240mm
Swiftech ClearFlex60 16/12mm

A rather big pacage :)

http://i267.photobucket.com/albums/i...a/ceaceb0f.jpg

Lots cardboard... it protects the stuff good anyway, which only is an advantage for me.

http://i267.photobucket.com/albums/i...a/0ff59684.jpg

Now to the content :) I love those boxes!

http://i267.photobucket.com/albums/i...a/445fb2e7.jpg

http://i267.photobucket.com/albums/i...a/257307b0.jpg

Tomorrow i will be testing if the rads fits inside the case... I'm keeping my fingers crossed right now!

Sorry that this update was a little late, do have a lot sleeveworks right now and regret priority over construction of the project.
It is a bit sad that I get so little feedback here on XS, this is after all one of my english home and favourite forums :(
Some more comments, feedback, suggestions, and much more would have been really nice!

Now on to what i have done:
-I have been scetching on how I will mount the rads for the most optimal tuberouting
-Mounted radiators (got a little problem with frontrad)
-Mounted some hardware :)

Plans for what to do:
-Paint some details in dark gray
-Moddify the frontplate so that the frontrad fits into place
-Sleevt the PSU and other wiring
-Mount the water blocks
-Mount the hardware
-Mount the fittings and the tubes
-Fil the system up and leak test
-Game the heck out of it in Dreamhack Winter 2012!
-Photo Shoot in the studio


Now the radiators are finnaly inside. ... but i had some problems with the frontrad... I need do moddify the baseplate of the frontpanel a little, so that the rad could fit to the bottom of the case as the endtank of the 240mm rad touches the front panel bottom plate , it shall be easy to fix with the dremel :)

It took several tries before I found the optimal location for water connection holes ... but damn good it was if one may say so myself ;)

http://i267.photobucket.com/albums/i...a/79dbb789.jpg

http://i267.photobucket.com/albums/i...a/09f3d192.jpg

http://i267.photobucket.com/albums/i...a/8cdcf677.jpg

Now the problem, the radiator cant sit toward the front panel, but it should be fixed pretty fast while those details I have chosen to be prepared for the paintjob.

http://i267.photobucket.com/albums/i...a/ccf5a0ac.jpg

http://i267.photobucket.com/albums/i...a/0524d376.jpg

I mounted the motherboard inside to get an overview of the whole thing, it looks very good so far!

http://i267.photobucket.com/albums/i...a/bac6cb06.jpg

http://i267.photobucket.com/albums/i...a/6dea14cb.jpg

Then i mounted an GTX470 and played with a sleevad extension cable of how it would look :)

http://i267.photobucket.com/albums/i...a/de1fce84.jpg

All the radiators are attached with very clean looking 6mm UNC-32 screws from MDPC-X

http://i267.photobucket.com/albums/i...a/3a919f33.jpg

http://i267.photobucket.com/albums/i...a/b645afa4.jpg

http://i267.photobucket.com/albums/i...a/d8db0de9.jpg

Snapcaps for the rear radiator screws... It's the details that make everything ;)

http://i267.photobucket.com/albums/i...a/3434e1cd.jpg

http://i267.photobucket.com/albums/i...a/41e86485.jpg

http://i267.photobucket.com/albums/i...a/458e0fbe.jpg

That's all for this time ... i hope to however to get more comments and feedback from all of you!
I know you can do better: D!

Best Regards
/ Venhar

Hmm ... some all black mobo would fit here EVGA Z77 miniITX :D

Attachment 129877

Moddify the frontplate so that the frontrad fits into place,ok... or cut it completely and make a new panel.
The new panel, which is a copy of the solutions that we have on the top Prodigy.
OFC there are many more of the work, cutting, painting ... but,
why not take the challenge ;)

overkill on cooling capacity with those 3 rads... overkill is good :)

Quote:

---

Originally Posted by Elder

Hmm ... some all black mobo would fit here EVGA Z77 miniITX :D

Attachment 129877

Moddify the frontplate so that the frontrad fits into place,ok... or cut it completely and make a new panel.
The new panel, which is a copy of the solutions that we have on the top Prodigy.
OFC there are many more of the work, cutting, painting ... but,
why not take the challenge ;)

---

Damn i love that board !
I will modify it today ;)
You will see more about it on the next update my friend :)

Quote:

---

Originally Posted by ZenEffect

overkill on cooling capacity with those 3 rads... overkill is good :)

---

Ovrekill is awsome ;)

Now for todays update!
I did not do a lot today, but it was much needed for my build and the whole theme ...
Today I prepared some details from the chassis before the paint began to watersand the metal parts which went very well but quickly... however the plastic front with the soft-touch finish on the took some time... luckily I already knew how to to 100% remove all the paint as it rises if you paint over it. I then got even a little time left over at the end out the day and drove out my newly painted VW Golf MKII out from the paint booth and ran into the details for paint...
I then went up to our color cabinet and began looking for a dark gray 2K varnish on Stansox's color database ...It didnt went as good as expected, I could not find the color I was looking for. The color I wanted is the MDPC-X Shade 19, which im going to sleeve the psu with.
I then started mixing my own costumcolor and after about 5-6 minute I got 98% out of the same color as the sleeve and then walked myself down to paint sprayguns and began to mix the paint with thinner and hardener, I sadly dont have pictures when painting the parts :/

Now on to some pictures, taken with my Sensation XE :/

Theese case details will be paintes:
-The front panel (the base of the frontpanel)
-The 240mm Mesh on the top
-The motherboard plate
-The PSU Bracket

http://i267.photobucket.com/albums/i...a/c8abe9d0.jpg

The color looks a little bit foggy, this is due to the quick drying thinner who simply does it job :)

http://i267.photobucket.com/albums/i...a/210f5805.jpg

http://i267.photobucket.com/albums/i...a/e891e558.jpg

Took them out to the outside for a little moment (better light)

http://i267.photobucket.com/albums/i...a/c8f95646.jpg

http://i267.photobucket.com/albums/i...a/0c2cfae9.jpg

After about 2 hours or so the paint had hardened (cured) completely, i the took the painted details with caution and test fitted them, looks totaly great if i can say so!

http://i267.photobucket.com/albums/i...a/a474960b.jpg

http://i267.photobucket.com/albums/i...a/3242b413.jpg

http://i267.photobucket.com/albums/i...a/2014a5cc.jpg

http://i267.photobucket.com/albums/i...a/b759ca82.jpg

I hope you appreciated the update so far :)

Hi guys !

Before you get an update on the little modification I made, I will show you what pagece I got lately
My expensive Taiwanese candy has finally arrived!
Thank you Bitspower and the whole team for their help and support in yet another project you are the best !

http://i267.photobucket.com/albums/i...a/46959b16.png




BP-Pacage! Damn i love em !

http://i267.photobucket.com/albums/i...a/06e1410c.jpg

http://i267.photobucket.com/albums/i...a/353f6ce6.jpg

Gues what this is ;) The winner gets a +REP!

http://i267.photobucket.com/albums/i...a/8d294719.jpg

Hello Guys!

Sorry for an late update, but better late than never....right ?

I started to take the case appart more, this time the case feet and handles. They had to be gone becaose of the rivets who are placed behind them and need to be removed so that i can take the bottom piece appart.

http://i267.photobucket.com/albums/i...a/74e2890e.jpg

After the drill it looket like this

http://i267.photobucket.com/albums/i...a/599eae94.jpg

Here you can take a look at the simple modification that i did, that piece touched the endtank and didnt let me to allign the rad with the holes, it also didnt let the rad to stay flush with the front. Could you think that a 2mm piece of plate could do such difference?

http://i267.photobucket.com/albums/i...a/8c8390f5.jpg

White rivets fromMDPC-X, a lot of them !

http://i267.photobucket.com/albums/i...a/cba4cd8d.jpg

Then it was time to rivet everything together, i also did the motherboard tray, went like a charm!

http://i267.photobucket.com/albums/i...a/e1ab43c9.jpg

http://i267.photobucket.com/albums/i...a/268f24d6.jpg

Something i am doing meanwhile!

http://i267.photobucket.com/albums/i...a/fcbc4029.jpg

http://i267.photobucket.com/albums/i...a/fcdb21c8.jpg

That was the update for tonight everyone :dremel:!