Under the Ice Single Stage picture guide

I started off with a Chilly1 evap and did some prep work on it. I used a drill and made some notches around the inside of the spiral. Then I used my Dremal to made some notches where my drill wouldn't work. Next I taped the inside of the suction channel. My intention is create more turbulance inside the evap.

http://www.under-the-ice.com/SingleS.../Img_0558S.jpg

http://www.under-the-ice.com/SingleS.../Img_0560S.jpg

I made sure to clean up all the metal filings with air pressure. Then I used my wire brush to get the evap really clean. The most important thing you can do to get a good braze job is to sand all metal points that get brazed. I like to use my polishing wheel, wirebrush, and sandpaper. Also be sure to purge with an inert gas. (nitrogen)

http://www.under-the-ice.com/SingleS.../Img_0562S.jpg

All I ever use is my mini torch

http://www.under-the-ice.com/SingleS.../Img_0563S.jpg

After you braze it is important to check for leaks but I like to clean the evap first because it's easier to lap without suction line. I'm counting on no leaks because if you have a leak you have to braze again and then clean again.

http://www.under-the-ice.com/SingleS.../Img_0564S.jpg

Next thing I do is put the suction line and captube on the evap. As you notice I brazed a piece of 1/4 copper on the evap. This makes it easier to install the captube and if I want to change out the captube it is much easier this way. Always swag the captube to make sure the ends are fully open. I use a safety pin.

http://www.under-the-ice.com/SingleS.../Img_0565S.jpg

http://www.under-the-ice.com/SingleS.../Img_0567S.jpg

http://www.under-the-ice.com/SingleS.../Img_0569S.jpg

Be sure to purge whenever you braze.

http://www.under-the-ice.com/SingleS.../Img_0570S.jpg

Now I wrap the captube around the end of the suction line about 10 times. This helps with sub-cooling.

http://www.under-the-ice.com/SingleS.../Img_0571S.jpg

After I braze I always put some paint on the brazed places. This helps to prevent oxidation.

http://www.under-the-ice.com/SingleS.../Img_0572S.jpg

Now I braze off captube end and pressure test.

http://www.under-the-ice.com/SingleS.../Img_0574S.jpg

Someone who is just getting started should pressure test before the do any cleaning or painting or you may find a leak and have to do it all over again.

Put a pressure gauge on the lineset to watch for pressure drop. I also submerge in water and look for bubbles which would show a leak.

http://www.under-the-ice.com/SingleS.../Img_0575S.jpg

Gotta rest my arm now. I'm getting typers elbow.

Lineset shows no bubbles.

Okay here is compressor and condenser.

http://www.under-the-ice.com/SingleS.../Img_0579S.jpg

Add your discharge line.

http://www.under-the-ice.com/SingleS.../Img_0580S.jpg

Be sure to purge while brazing

http://www.under-the-ice.com/SingleS.../Img_0580S.jpg

Here I added filter/drier and suction accumulator. (personal prefference on the accumulator)

http://www.under-the-ice.com/SingleS.../Img_0581S.jpg

http://www.under-the-ice.com/SingleS.../Img_0582S.jpg

http://www.under-the-ice.com/SingleS.../Img_0587S.jpg

Now back to more lineset prep. I use some 3M rubber waterproof tape to hold captube to suction line tightly. This also helps with sub-cooling.

http://www.under-the-ice.com/SingleS.../Img_0588S.jpg

http://www.under-the-ice.com/SingleS.../Img_0589S.jpg

I now put the insulation on the lineset and braze it to the accumulator. Always purging with nitrogen. Purging helps to prevent and oxidation inside the system.

http://www.under-the-ice.com/SingleS.../Img_0590S.jpg

On this unit I brazed the captube to the accumulator just for GRAY MOLE :) this also helps with sub-cooling. Some people see no need for this.

http://www.under-the-ice.com/SingleS.../Img_0591S.jpg

Now I braze the captube into the filter/drier

http://www.under-the-ice.com/SingleS.../Img_0593S.jpg

Now I pressure test.

http://www.under-the-ice.com/SingleS.../Img_0594S.jpg

After about 36 hrs on the vacuum pump, I gave it a charge.

http://www.under-the-ice.com/SingleS.../Img_0595S.jpg

Gray will be happy with this. :D

http://www.under-the-ice.com/SingleS.../Img_0596S.jpg

Now I'll finish up with some painting, mesh, and load testing.

http://www.under-the-ice.com/SingleS.../Img_0597S.jpg

After paint I added a few brackets to hold copper tubing in place during shipping and after.

http://www.under-the-ice.com/SingleS.../Img_0599S.jpg

http://www.under-the-ice.com/SingleS.../Img_0601S.jpg

More insulation with liquid glue between joints.

http://www.under-the-ice.com/SingleS.../Img_0602S.jpg

I'm a little overcharged but load testing will take care of that.

http://www.under-the-ice.com/SingleS.../Img_0603S.jpg

Next up is the suction line mesh. ;)

http://www.under-the-ice.com/SingleS.../Img_0604S.jpg

Next is mounting enclosure.

http://www.under-the-ice.com/SingleS.../Img_0608S.jpg

http://www.under-the-ice.com/SingleS.../Img_0609S.jpg

http://www.under-the-ice.com/SingleS.../Img_0610S.jpg

Compressor is a Danfoss SC18CLX.2 (3/4hp) with matched condenser
Captube is .040 at 11'
Suction line is 5'
Refrigerant is r507 with POE oil

As always, beautiful work ron.
Those CE condensers look quite nice. And a good compressor choice of course; are these the old stock or did you Grainger/direct order up the compressor?

Captube brazed/soldered looks good, clearly has good transfer to the pipe, but also shows hot much heat your passing off. Looks like its icing on the bottom of the accumulator just fine!

What's your preferred evap cleaning method? You certainly look like you ground off ANY excess braze. Is it that dual shaft grinder in the background that I see? :)

Yes Adam I use the grinder (I need a smoother stone) I also use one of those 3M fiber wheels. Gets the job done fast. Not Grainger but compressors are new. I wish you were here to give me a hand. :)

Find me a ticket and throw some burgers on the grill and I'll be down their pushing out evaporators like an overdue woman in labor.

WoW very nice Ron. Thanks for doing this ! :)

I made this sticky :)

Awesome work Ron:)

OMG this is great. much nicer than the one I have.

Great looking unit Ron.:up::up::up:

Did you ever try soft solder when securing the captube around the copper lines. The advantages are you don't use the expensive 15% silver solder and you only need to heat to 600/650 F degrees. You do need to use flux with the soft solder.

But Nothing wrong with brazing. :yepp:

Walt

It's funny you say that Walt because there is a story behind it. :)
As you can see my bench top get's cluttered as I'm working on a project. I try to get it organized before I start. I did have some plumbers soft solder on that bench somewhere but couldn't find it. I got tierd of looking and grabed my Butane torch and Radio Shack "Rosin-Core Solder" .032 dia. I had to double it over about ten times to make it thick enough to usebut it worked. ;)
thanks Walt.

EDIT - LMAO - I looked back at the second picture and I found my plumbers soft solder. It was right in front of me when I started.

Up to .040" I see! Good stuff, should perform well.
Not a fan of the paint, but hey, everyones got a different style. ;)

What mount is that though? Do you know what material that block foam is on the inside?

Quote:

---

Originally Posted by runmc

Lineset shows no bubbles. Now I let it sit and see if I get a pressure drop. Probably don't need to do this if you don't have bubbles, but it doesn't hurt.

http://www.under-the-ice.com/SingleS.../Img_0578S.jpg

---

Hi Ron -- great tutorial, very nice work, but I just had to comment on this.

Do you have some magic way of sensing pressure drop? Reason I ask is that I don't see a gauge hooked up, and even if that Schrader has a pin in it, hooking up a hose and gauge normally results in a small loss even with self sealing couplings (or at least mine do). That small loss could be interpreted as a pressure drop, especially considering the small volume being looked at.

Quote:

---

n00b 0f l337: Find me a ticket and throw some burgers on the grill and I'll be down their pushing out evaporators like an overdue woman in labor.

---

:rofl:

Hey Mytek, I think he had it hooked to his gauge set at the time, or his pressure regulator :)

that compressor looks familiar:D

great writeup Ron, that brazing work looks perfect:up:

Quote:

---

Originally Posted by mytekcontrols

Hi Ron -- great tutorial, very nice work, but I just had to comment on this.

Do you have some magic way of sensing pressure drop? Reason I ask is that I don't see a gauge hooked up, and even if that Schrader has a pin in it, hooking up a hose and gauge normally results in a small loss even with self sealing couplings (or at least mine do). That small loss could be interpreted as a pressure drop, especially considering the small volume being looked at.

:rofl:

---

Your right Michael. My wording and picture arrangement were off in this post. I already had it hooked up to my gauges and did a pressure check. I also filled my kitchen sink and did a bubble check.I never trust Schrader valves. They will let you down.