-
EVGA X58 3X SLI Classified MB waterblock installed
-
temp comparison before and after
-
Very nice!
What kind of temps are you getting?
-
Oh shiiii. That thing is gorgeous :)
-
Aaaauw that is so pretty !
-
Very very nice! I was wondering....Do you have to use the thermal pads or can you use thermal grease? I would think you would get better temps with some MX2 or something.
-
Nice, that is some sexy block for a a great Motherboard, congratulations :)
Whats is the lowest chip at the bottom cooled by the block ?
http://img5.imageshack.us/img5/2486/dscf0103j.jpg
-
Quote:
Originally Posted by
Sadasius
Very very nice! I was wondering....Do you have to use the thermal pads or can you use thermal grease? I would think you would get better temps with some MX2 or something.
Thermal pad is for other minor chips, for X58 chips, NF-200 and South Bridge, I applied some MX2 for sure. :)
As you see, my loop is first go to a 4GHz i7 920 CPU and then goes to the MB waterblock, so warm water is going into it....the temperature will be expected to be a bit higher. :)
It is priming now, system temp = 40-41C constantly, 28(ambient temp), idle is something about 37-38C. Now I don't need to use a fan to blow the north bridge heatsink, silent!! :D
-
Koolance has certainly turned around lately :)
Freaking gorgeous.
-
-
Any internals? I heard that water doesn't flow through the entire block, but only through the NB area.
-
No mosfet block? What temps are you getting on the mosfets? I went from 85+ down to mid 60s when i switched to the koolance x58 blocks.
-
Koolance, I take my hat off to you. Your recent stuff is da bomb.
-
Quote:
Originally Posted by
veedubfreak
No mosfet block? What temps are you getting on the mosfets? I went from 85+ down to mid 60s when i switched to the koolance x58 blocks.
which block did you use for the mosfets? the one which koolance recommends?
Quote:
Originally Posted by
SoulsCollective
Koolance, I take my hat off to you. Your recent stuff is da bomb.
yea, koolance is slowly but surely gaining a foothold in the water cooling community again :up:
-
BEOYTCH!!!!!!!!!!!!
mine comes in a few hours! :rofl:
But yeah nice show... u beat me to it by a couple of hours!
Quote:
Originally Posted by
veedubfreak
No mosfet block? What temps are you getting on the mosfets? I went from 85+ down to mid 60s when i switched to the koolance x58 blocks.
I should be getting everything soon. I'll post internals if you guys want because im painting the plate red.
But dean personally mailed out my stuff and i lost the race in installing them. :rofl:
Dean!!
-
are you using different 7/16" tubings? it looks like the tube connecting the CPU block to the chipset block is more clear than the other tubes. or are they all tygon? and it doesn't look like you have any kinking problem even with that tight radius bend. can you quickly measure the distance between the two barbs connecting the NB to the CPU? much thanks!
-
Quote:
Originally Posted by
Baleful
Any internals? I heard that water doesn't flow through the entire block, but only through the NB area.
I think no, from the block there is a X58 marked, you can look into the block inside.
I did not open the block, just hurry to install it.
http://img154.imageshack.us/img154/381/dscf0103.jpg
Just I feel that the heat transfer from the Vtt PWM to water block is not doing very good, I still feel hot from that area.
-
Quote:
Originally Posted by
TinTin
I think no, from the block there is a X58 marked, you can look into the block inside.
I did not open the block, just hurry to install it.
Just I feel that the heat transfer from the Vtt PWM to water block is not doing very good, I still feel hot from that area.
Ahh ok, well I would like to see what the insides look like on this thing.
-
Quote:
Originally Posted by
WhiteFireDragon
are you using different 7/16" tubings? it looks like the tube connecting the CPU block to the chipset block is more clear than the other tubes. or are they all tygon? and it doesn't look like you have any kinking problem even with that tight radius bend. can you quickly measure the distance between the two barbs connecting the NB to the CPU? much thanks!
Yes, they are all tygon R3603 1/2" ID, 3/4" OD.
Because, the other tube are older. So it look the one is more clear! :D
About 110mm c/c
-
Quote:
Originally Posted by
NaeKuh
BEOYTCH!!!!!!!!!!!!
mine comes in a few hours! :rofl:
But yeah nice show... u beat me to it by a couple of hours!
I should be getting everything soon. I'll post internals if you guys want because im painting the plate red.
But dean personally mailed out my stuff and i lost the race in installing them. :rofl:
Dean!!
waiting for your internals photo ;)
-
Quote:
Originally Posted by
NaeKuh
BEOYTCH!!!!!!!!!!!!
mine comes in a few hours! :rofl:
But yeah nice show... u beat me to it by a couple of hours!
I should be getting everything soon. I'll post internals if you guys want because im painting the plate red.
But dean personally mailed out my stuff and i lost the race in installing them. :rofl:
Dean!!
who knew transit time to hong kong was shorter than cali :ROTF:
-
Quote:
Originally Posted by
[Koolance] Dean
who knew transit time to hong kong was shorter than cali :ROTF:
:rofl:
I once shipped a package from podunk Hudson,NH to Hong Kong
Dropped it off at 10:30am on a saturday and it was on the guys desk at 2Pm on tuesday..
-
Quote:
Originally Posted by
NaeKuh
...snip...
I should be getting everything soon. I'll post internals if you guys want because im painting the plate red.
...snip...
http://deephousepage.com/smilies/gonnagetit.gif
;):p:
-
Quote:
Originally Posted by
[Koolance] Dean
who knew transit time to hong kong was shorter than cali :ROTF:
I suppose got it yesterday, I was at home, but the UPS stupid guy said my home is empty in the tracking record.....hahahaha!!
-
Quote:
Originally Posted by
TinTin
I suppose got it yesterday, I was at home, but the UPS stupid guy said my home is empty in the tracking record.....hahahaha!!
well funny thing is dean placed the order for me when it wasnt even for sale yet.
lol i was stalking him, and he was stalking the delivery guy from the factory.
When the blocks came in, there was no point in rushing it cuz it would of gone out the next day and arrived next week. :\
but yeah... its funny how u got them b4 i did, and i bought them b4 they were listed for sale. :up:
Couple more hours til ups arrives.
Quote:
Originally Posted by
Waterlogged
Lemme paint it red first, then i can stripe it black with your method if the red is too overpowering. :up:
EDIT: UPS ARRIVED
