second place at ripping.org :D
http://valid.canardpc.com/show_oc.php?id=465080
hopfuly get to 4.8GHz
Printable View
second place at ripping.org :D
http://valid.canardpc.com/show_oc.php?id=465080
hopfuly get to 4.8GHz
Nice. what batch do you have. is this on air/water/phase/LN2?
batch is L832B701 EO, this a on a SS phase changer,Quote:
Originally Posted by clo007
Excellent. same batch I got from Microcenter couple weeks ago. I am ready to play with mine this weekend finally.
This UD3P continues to amaze me! Nice clocks!
i also got mine from Microcenter two weekend ago, i hope u get a good chip:up:Quote:
Originally Posted by clo007
As in MicroCenter on Elston Ave in Chicago ??????
I've got my Q9450 up to 3.6 on air ... would it make more sense to upgrade the CPU or change cooling? From my reading 3.6 is about as far as I should go on air??
You would need one hellofa air coolerQuote:
Originally Posted by clo007
great numbers
Awesome work :up: i'm so glad I got a UD3P too :).
BTW any benchmarks?
I'v seen a Q9650 do 4.8GHz on air.Quote:
Originally Posted by Acekiller
only had time to run 1m superPI 09.996sQuote:
Originally Posted by fatguy1992
tryed for 4.8 but couldn't get it validated:down:, now cant get 4.7 back:shakes: mmm...
deummm
Quote:
Originally Posted by EliTE22
chalk up another for the UD3P
\
Nice job:up:
nice clocks, wish I had a good batch.
Very respectable clocks and voltages. Great job! :up:
elite22,may ask what your bios settings are?
Nice quad fsb. Great clocking. Congrats. Keep pushing for 1st place :clap:
http://valid.canardpc.com/cache/banner/499517.png
4.46 on set-up in sig :)
gamed on it for 45 minutes last night and hit 60C on the mark. it took 1.5 volts bios/ 1.46 actual load to get it there.
Awesome :up:
Sure:DQuote:
Originally Posted by radaja
[/QUOTE]PHP Code:******Gigabyte EP45 UD3 Template*******
Robust Graphics Booster [auto]
CPU Clock Ratio [8x]
Fine CPU Clock Ratio [+0.5]
**********Clock Chip Control***************
CPU Host Clock Control [enable]
CPU Host Frequency (Mhz) [554]
PCI Express Frequency (Mhz) [100]
C.I.A 2 [disable]
*********Advanced Clock Control**********
CPU Clock Drive [800mv]
PCI Express Clock Drive [800mv]
CPU Clock Skew [unchanged]
MCH Clock Skew [unchanged]
*******DRAM Performance Control********
Performance Enhance [turbo]
Extreme Memory Profile (XMP) [auto]
(G) MCH Frequency Latch [auto]
System Memory Multipler [2.00B]
Memory Frequency [1108]
DRAM Timing Selectable [manual]
CAS Latency Time [5]
tRCD [5]
tRP [5]
tRAS [15]
*******Advanced Timing Control***********
didnt touch ram timings auto
tRRD []
tWTR []
tWR []
tRFC []
tRTP []
Command Rate (cmd) []
***********Motherboard Voltage Control*******
Load-Line Calibration [enabled]
CPU Vcore [1.4875V]
CPU Termination [1.500V]
CPU PLL [1.670V]
CPU Reference [0.935V]
MCH Core [1.620V]
MCH Reference [1.120V]
MCH/DRAM Refernce [0.990V]
ICH I/O [1.570V]
ICH Core [1.200V]
DRAM Voltage [2.160V]
DRAM Termination [auto]
Channel A Ref [auto]
Channel B Ref [auto]
Channel Timing Settings [B]didnt change[/B]
Static tRead Value []
tRD Phase0 Adjustment []
tRD Phase1 Adjustment []
tRD Phase2 Adjustment []
tRD Phase3 Adjustment []
tRD 2rd (Differnt Rank) []
tWR 2wr (Differnt Rank) []
tWR 2rd (Differnt Rank) []
tRD 2wr (Same/Difft Rank) []
Dimm 1 Clock Skew Control []
Dimm 2 Clock Skew Control []
DDR Write Training []
Channel Driving Settings
Drive Strength Profile []
Data Driving Pull Up Level []
cmd Driving Pull Up Level []
ctrl Driving Pull Up Level []
clk Driving Pull Up Level []
Data Driving Pull Down Level []
cmd Driving Pull Down Level []
ctrl Driving Pull Down Level []
clk Driving Pull Down Level []
*****************Advanced BIOS Features*********
CPU Multithreading []
Limit CPUID Max to 3 []
No-Execute memory Protect []
CPU Enhance Halt (CIE) [disable]
C2/C2E State Support [disable]
C4/C4E State Support [disable]
CPU Thermal Monitor [disable]
CPU EIST Function [disable]
Virtualization Technology [enable]
well done Elite!
but, if it is on a phase change, why do you have so bad temps? or does it read incorrect?
thanks elite22.
it reads incorrect, temps were -30c at the bottom of the evapQuote:
Originally Posted by SupeRClockeR