Is there any problems with the 1/2x3/4 BP comp. Fittings. Do they seal fully on the blk without any problems or mods..I have noticed the swifty logo needs to be removed..
Printable View
Is there any problems with the 1/2x3/4 BP comp. Fittings. Do they seal fully on the blk without any problems or mods..I have noticed the swifty logo needs to be removed..
Please use the ST transfer Adapter and then you will have perfect seal.Quote:
Originally Posted by gmod
Due to all of our fittings are all hidden O-Ring design.
could you give me a link to where i can get those. Want to make sure i get the right ones..And what about the EK 4870x2 full cover blks. Anything i need for thoseQuote:
Originally Posted by BP-Vincent
Apparently if you put another O-Ring over the thread they should work ok.
The thing that bothers me about that is O rings tend not to seal well against a second O ring. I mean look at a car's oil filter, if you accidentally double up the O ring there (old oil filter's O ring sticks to the engine block) then you have an almost guaranteed leak. Plus, you reduce how many threads are actually threaded in.Quote:
Originally Posted by Scubar
I'd personally play it safe and just use the adapters that Vincent suggested. Should be no issues at all then.
are BP barbs (not compression) ok to use on the MCW-30 without the ST adapter???
If it is a captive O-ring type barb you will need either a spacer or another O-ring.
Is this issue only with Swiftech blocks, or is it something that is a problem with say D-Tek blocks as well?
We prefer you add one ST Adapter for perfect seal...Quote:
Originally Posted by SNiiPE_DoGG
This was designed for Swiftech's issue only..
Sure..now if there are the same design with swiftech...please sure you are using correct our components for WC.Quote:
Originally Posted by rehpyc
how about using BP compresion Fitting 3/4 OD on the side of EK RES?, what adapter do you recomended
these?Quote:
Originally Posted by BP-Vincent
http://www.performance-pcs.com/catal...ducts_id=23836
Yes.
Yes, this is the way to do it right.:up: The o-ring trick may work, but it doesn't leave a whole lot of threading in there. This adapter is fairly long with lots of threads, so you'd get really good strength, not to mention the exact threading.Quote:
Originally Posted by RealRedRaider
If only other stores could provide these adapters among their BP products in stock.. performance-pcs charges an arm and a leg for shipping :(
Can try carefully filing down the lip that surrounds the o-ring. Personally, an adapter on a fitting is just too much going on, I'd find a different solution. Luckily, I am not a fan of the compression fitting :)
I can get about 1-3/4 turns using the o-ring idea. I wouldn't do that if both o-rings weren't retained, but with the way the GTZ is, the extra o-ring is retained by the block and the fitting o-ring is retained by the barb, so I think it seals ok. It's only holding on by just under 1-3/4 threads, so the transfer fittings would be the better way to go though.
Whoa, wait just a minute here! I thought the GTZ had G1/4" threads?Quote:
Originally Posted by Martinm210
it haves, but to use a bitspower fitting you need to use a extender, else you need to remove the sticker and maybe void the garantee :shrug:Quote:
Originally Posted by Waterlogged
The problem there is, the BP ST transfer fitting has NPSM male thread which are longer than most fittings have. This will cause the mis-alignment between the 18 TPI of the NPSM and the 19 TPI of the BSPP (G).Quote:
Originally Posted by CrixD
ahhh... I can see that :p Sorry ;pQuote:
Originally Posted by Waterlogged
NP at all. :up:Quote:
Originally Posted by CrixD
Well thats put a dent in my plans. I was hoping to use the GTZ with the BP Compression fittings. However i cant seem to get that adaptor in the UK.
So are you saying that the adaptors arent going to work properly anyway then ?Quote:
Originally Posted by Waterlogged
Good catch, I don't have any of those transfer fittings, but if I try to feed a plastic swiftech barb down in there it does seem to bind up pretty quick.Quote:
Originally Posted by Waterlogged
So, ideally we would need a G1/4 extender (NOT the BP bpsm-bspp thread adapter) with NO recessed o-ring, correct? I don't think something like that exists.
Koolance has the only G1/4 extender I know of and they have recessed o-rings.
You could use a DD male-to-male fitting, those have exposed o-rings, coupled together with a BP female-female coupler. But that's gonna look tremendously...ugly.
Weird why Swiftech designed their newest block with a built-in recess when most other blocks have a flat face.