this is the error !!
please help!!
i try g27-28 same problem,pata sata same problem,with one card is ok but in c.f. not !!!!:mad:
the boot finish here !!
http://img175.imageshack.us/img175/7...gine002vc9.jpg
Printable View
this is the error !!
please help!!
i try g27-28 same problem,pata sata same problem,with one card is ok but in c.f. not !!!!:mad:
the boot finish here !!
http://img175.imageshack.us/img175/7...gine002vc9.jpg
pls try "reset configuration data" within bios.
I have not understood what I must make where I find the this voice reset configuration data in the bios!!
In pnp/pci configuration config, also check "pci-e complaincy" mode under advenced chipset config.
I boot fine with one card under P05 bios, maybe there is bios issue with 2 cards...
nothing i try to change this paramether but the problem is the same!!
Hmm does one card work for u?
I think bios is the issue...there were similar problems with this chipset(x38/x48) with 3870x2 which new bios rectified. And it seems this issue is not confined to BlackOPS either. Many boards are not able to complete boot with 2 cards installed.
Iīve got the exact same problem. One 4870x2 works fine and if I plug in the second one BlackOPS ends with this message. Postcode 8b.
F***ing hell. I hope this is fixable, my whole setup is waiting for 2 of these cards..
spl what kind of psu do you have?
http://forums.hexus.net/abit-care-he...t-code-8b.html
3rd post down says 8b is power-related.. those x2's draw a lot of power
Uh, i hope it's not pci-e power that's the problem...
t.t.1200w
I checked power consumption with a power meter. With BlackOPS, E8600 @ 500x6 1.25 volt vcore and one card I had a consumption of about 370-380 watts while booting. A second card shouldnīt be a problem for our OCZ EliteXStream 1kw. But surprisingly power consumption remained nearly the same after installing card no. 2. :shrug:
That was my first impression while dealing with this problem.
After several attempts I changed motherboard (ASUS Maximus Extreme), cpu (qx9650) and psu (I tried Silverstone OP1000 and Xilence 1200). With ASUS Maximus Extreme I didnīt get a screen when both cards were installed.
Funny thing is that the system itself was up and running. Because after some seconds I could shut down the pc with pressing windows key -> arrow up -> enter -> arrow down -> enter on my keyboard. That means that my system was in windows vista and reacted the right way - but without a picture on my screen.
I will have 2 cards soon I will test.
Yeah this is a definite question for me! Im getting 2 board to CF
Based on MusicIsMyLife's last comment, this sounds very much like a bios issue... its getting confused somehow and not initialising the display.
2 cards due to arrive today. Will test tonight in BlackOps and P5E3 Prem.:up:
^^ Let me know how it goes! Im between those two and a RE
OK. received 2 new 4870x2's today and after several hours of testing, I found the exact same issue as spl above. I didn't try any other bios than G28 but I believe this could be a BlackOps bios problem because the same 2 cards run in crossfirex on my P5E3 Prem mobo using bios 0505 :shrug:. I used the drivers on the install disc that came with the cards. 8.8 beta did not work and the official 8.7 from guru3D did not work on my asus board. I tried all of these on BlackOps to no avail. Every attempt was stopped cold during post with the "AHCI Bios not installed!!" I disconnected all extra stuff on the board to make sure there was no power issues. 3DMark benching requires about 980 watts with 2 4870x2 and qx9650.
(2x1 gb, Vista 32bit).
Saaya,
Please bring this issue to the bios engineers.
Thanks!
http://resources.vr-zone.com/Shamino/7A3F1G29.BIN
will u try g29 , sorry i just only have 1 card still waiting for another...