UT P35 + E8500, fsb 608

DFI ut p35, bios 17/3, E8500 Q807***, LN2, ballistix pc8500 2.45v, win xp pro as it was for daily use :

Try some Tweaks next time.... i think a better time is possible.

for daily use xp is that really nice score

Nice clocks indeed. :)

Very nice mate..Wish my Asus Maximus Extreme would hit over 550FSB... :(

If you did a clean install and some copy wazaa I bet you could close in on 8 min 30 sec 32M

Great score
:up:

nice clocks man. give it some more vcore:rolleyes::eek:

nice fsb on the DFI P35 :up:

great score with xp for daily use... expecting some scores with tweaked xp ;)

and great fsb for UT :up:

Very nice clocks!
Can you tell us about your settings used to hit 608 fsb? :)

Looks good, but u can 4 sure see better 1m and 32m time... Go work on it

Keep pushing it.

I heard good things about those boards :p

hey DDA wanna share your voltage settings\ other bios settings:D

tks all

no secrets, we are here to share our experiences and findings

for my ram

- all precharge to act 5
- performance level 8
- trrd 4
- trtp 4
- gtl ref, 72/72/70

voltages, most of all to max; fyi, vcore was set in bios at 1,94; probably cpu-z went nuts

Nice Clock DDA:clap:

the DFI seems to be the best P35 based mobo for the Wolfdale.

congrats and keep pushing

Is there anything besides Commando that comes close to this board for Wolfdale?

nice results keep pushing :D

Quote:

---

Originally Posted by DDA

tks all

no secrets, we are here to share our experiences and findings

for my ram

- all precharge to act 5
- performance level 8
- trrd 4
- trtp 4
- gtl ref, 72/72/70

voltages, most of all to max; fyi, vcore was set in bios at 1,94; probably cpu-z went nuts

---

You set all the votages to max? How did you cool chipset? Stock cooling?

nice job!

Quote:

---

Originally Posted by runmc

You set all the votages to max? How did you cool chipset? Stock cooling?

---

cs stock; ambient 18°, 3 fans 120mm blowing all over the mb

Very nice results DDA :clap:

Here is what I managed on my DFI LP UT P35 and E8400 (Q739 ES)

http://www.max-save.org/pix/zm566rb_thumb.jpg

http://valid.x86-secret.com/show_oc.php?id=364171

So, 600MHz, but with multi 6, totaly unstable, unfortunatelly.

I can boot from BIOS on 590MHz, and run 1M on 580MHz.

My settings were:

SB: 1.15v
PLL: 1.75v
NB: 1.77v
VTT: 1.45v
GTL: 90/89/89

Everything was on air :)

Cheers :)

P.S. one quick question - my board doesn't boot if VID voltage is set higher then 1.44v (so with 1.45 it doesnt boot),
then I tried raising offset, and same thing happed, but I can raise i to ~104%, higher then that - board won't boot.

So max voltage I can give is 1.53v :( Any suggestions, I'd be gratefull, and sorry on OT, DDA.

Quote:

---

Originally Posted by Razer

Very nice results DDA :clap:

Here is what I managed on my DFI LP UT P35 and E8400 (Q739 ES)

http://www.max-save.org/pix/zm566rb_thumb.jpg

http://valid.x86-secret.com/show_oc.php?id=364171

So, 600MHz, but with multi 6, totaly unstable, unfortunatelly.

I can boot from BIOS on 590MHz, and run 1M on 580MHz.

My settings were:

SB: 1.15v
PLL: 1.75v
NB: 1.77v
VTT: 1.45v
GTL: 90/89/89

Everything was on air :)

Cheers :)

P.S. one quick question - my board doesn't boot if VID voltage is set higher then 1.44v (so with 1.45 it doesnt boot),
then I tried raising offset, and same thing happed, but I can raise i to ~104%, higher then that - board won't boot.

So max voltage I can give is 1.53v :( Any suggestions, I'd be gratefull, and sorry on OT, DDA.

---

i had same issue; reflashed bios and OK
give GTL 72/72/70

Thanks for the tip, will try that :)

BTW how much should I give for VTT? Is it 1.45v fine, or should I lower it?