Domnianator 6400C4D timings?

Printable View

08-03-2007, 04:13 PM
Skrips

Domnianator 6400C4D timings?

Hey hey, haven't been on the forums for a bit, but here is the deal Yellow Beard:

I have that new system I was building a while back, and I am finally satisfied that all the parts have passed the time / real world stress test. Now, its time to up the settings. I know, according to what I have heard, that the ram I have will run at 4-4-4-12 2T settings, but whenever I set the ram to these speeds my system will not boot windows. Just gets a black screen then nothing.

Now, I am by FAR no expert in clocking things past default, but its time to try and figure it out. I posted the problem here in the MoBo thread, and decided to make a post here as well.

Any help would be awsome, thanks!
08-03-2007, 04:39 PM
Yoxxy

With the 680i you will need to increase Northbridge and FSB Termination voltage to allow you to run 4x1 gb.

The timings should be 4-4-4-12 @ 800 mhz.

Quote:

Originally Posted by Skrips

Hey hey, haven't been on the forums for a bit, but here is the deal Yellow Beard:

I have that new system I was building a while back, and I am finally satisfied that all the parts have passed the time / real world stress test. Now, its time to up the settings. I know, according to what I have heard, that the ram I have will run at 4-4-4-12 2T settings, but whenever I set the ram to these speeds my system will not boot windows. Just gets a black screen then nothing.

Now, I am by FAR no expert in clocking things past default, but its time to try and figure it out. I posted the problem here in the MoBo thread, and decided to make a post here as well.

Any help would be awsome, thanks!
08-03-2007, 04:43 PM
Skrips

Well, I am testing the ram right now, got it working at 4-4-4-12 2T @2.1v

Not sure if this is good or not, but so far no problems. I am trying to remember WHICH ram torture test everyone uses here to test the ram stability...once I can remember, I will snag it and test the ram to its fullest.

Thanks for the help!
08-03-2007, 05:06 PM
ChaosMinionX

Memtest 86+ V1.7 or better......
08-05-2007, 04:55 AM
Yellowbeard

Don't make your computer angry.....you won't like it when it's angry.

JK, how is the testing coming along?
08-08-2007, 05:22 PM
KALISPIMENTA

Will this settings work good with the 680I and a Q6600?
Sli ready: Disabled
Memory Voltage: 2.0v
TCL: 4
TRCD: 4
TRP: 4
TRAS: 12
Command Per Clock: 2
TRC: 24
Also what in the IC for this memory?
Part Number = CM2X1024-6400C4D
Version Number = 2.2
Lot Number = 0645285.5
XMS Number = XMS6404

These modules were not listed in the IC list.
Thank you.
08-09-2007, 07:47 AM
Yellowbeard

Those settings should work except for the memory voltage. If it is not stable at 2.0, set it to the (tested) voltage, 2.1v.

Also, a rev 2.2 is almost certainly Promos. However, I cannot access that information. Please post in that thread and RAM GUY will update it with your part # and ICs.
08-09-2007, 04:48 PM
KALISPIMENTA

Quote:

Originally Posted by Yellowbeard

Those settings should work except for the memory voltage. If it is not stable at 2.0, set it to the (tested) voltage, 2.1v.

Also, a rev 2.2 is almost certainly Promos. However, I cannot access that information. Please post in that thread and RAM GUY will update it with your part # and ICs.

I did thank you