Printable View
Hey guys,
I'm looking for suggestions as how to get through this fsb wall... i know it's the fsb cuz everything is super stable up to 324.. and nothing happens at 325. I'm thinking more volts.. but... I don't think that's the case either to vcore or vmch.. c1e.. all that stuff is disabled... time for a new processor?
400 FSB should be possible mate, upped NB voltage to 1.4 ? Can ou plz post your bios settings here as this info is not enough to determine the cause of find a solution
This is basically the highest stable point I get..Quote:
JumperFree Configuration Settings
AI Overclocking: Manual
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
FSB Frequency: 320
PCI-E Frequency: 100
DRAM Frequency: DDR2-640 (1:1)
DRAM Timing Control: Manual
CAS# Latency: 5
RAS# to CAS# Delay: 5
RAS# Precharge: 5
RAS# Activate to Precharge: 15
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: AUTO
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.40000
CPU Voltage Reference: AUTO
CPU Voltage Damper: Enabled
CPU PLL Voltage: AUTO
DRAM Voltage: 2.10
FSB Termination Voltage: AUTO
North Bridge Voltage: AUTO
North Bridge Voltage Reference: AUTO
Advance CPU Settings
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
PECI: Disabled
At one point.. I pushed the Vcore to 1.45.... NB voltage to 1.7... PLL 1.7... over-charging... 1000mV... all of this stuff I gradually moved up to. Any suggestions are greatly appreciated.. my RAM is buffalo firestix 6400.. d9gmh so that isnt the problem i think.
Drop the CPU multiplier to see if the board can run 400FSB and to eliminate the CPU isn't holding you back, this should be doable with the below settings... test it throuroughly then up the multi back to 9 and up the Vcore accordingly, it could be it need over 1.55 volts to get it stable at 3600mhz
JumperFree Configuration Settings
AI Overclocking: Manual
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9 --> drop to 8x
FSB Frequency: 320 --> 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-640 (1:1) --> DDR800
DRAM Timing Control: Manual
CAS# Latency: 5
RAS# to CAS# Delay: 5
RAS# Precharge: 5
RAS# Activate to Precharge: 15
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: AUTO
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.40000 --> 1.45
CPU Voltage Reference: AUTO --> 0.63x
CPU Voltage Damper: Enabled
CPU PLL Voltage: AUTO --> 1.5
DRAM Voltage: 2.10
FSB Termination Voltage: AUTO --> 1.3
North Bridge Voltage: AUTO --> 1.4
North Bridge Voltage Reference: AUTO
Advance CPU Settings
CPU Ratio Control: Manual
- Ratio CMOS Setting: 8
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
PECI: Disabled