DFI ICFX3200 T2R/G FSB Scaling & Voltage Settings
I've done some extensive testing with the RD600 and have compiled the data into a quick chart to help others in setting up quick overclocks on their board. Memory was left async, DDR2-800, 2T for most of the tests. All testing done on open test bed (HSPC Top Deck Tech Station). North bridge cooled by Microcool NorthPole XE Whisper Chipset Cooler, cpu cooled by Tuniq Tower with stock fan. Your results may vary, but these were the exact settings used to reach each final result.
CPU: E6400 L628B194
Memory: G. SKill 6400 HZ's
Video: Evga 7900GT's
PSU: OCZ GameXtreme 700w
Case: HSPC Top Deck Tech Station
**** Use these voltages & settings at you own risk****
It has been said by other more knowledgable enthusiasts that 1.5v on the nb is the max safe 24/7 voltage.
http://img.techpowerup.org/070210/RD...ling chart.jpg
Bios Settings
[HTML]
Genie Bios
>Performance options
Memory Clock Frequency: DDR-400
Control CPU Frequency: Manual
x CPU Frequency (Mhz): 4XX
NB FSB Strapping: Auto or 333
PCI-E Overclock: 105
Software Reset Clockgen: Enabled
Memory Overclocking: Disabled
Overclock Frequency(MHz):
>NorthBridge ASIC CFG
>NorthBridge Selections
Memory Channels: Auto
Memory Power Mangement: Disabled
IGD Clock Gate: Disable
NB Channel Mapping: Auto
Simple Addr Translation:Disable
Chip-Select Swap: Disable
Burst Length: 8
Bank0 Map GFX: 4
Bank1 Map GFX: 5
Bank2 Map GFX: 6
Channel Mapping NB: 5
Channel Mapping GFX: 1
Bank0 Map NB: 5
Bank1 Map NB: 11
Bank2 Map NB: 7
>Memory Timing Menu
CS Output Timing: Delay 1/4 clock
CK Output Timing: AUTO
Dual channel Split Mode: AUTO
ADDR/CMD Driving Pre-AMP: Disabled
ADDR/CMD Driving Strength: 05
Clocking Driving Pre-AMP: Always
Clocking Driving Strength: 05
Address/Command Timing: Auto
Memory Timing Select: Manual
CAS Timing (TCAS): 4
Read RAS-CAS Delay (TRCDR): 4
Write RAS-CAS Delay (TRCDW): 4
RAS Precharge Time (TRP): 4
Cycle Time (TRAS): 12
Row Cycle Time (TRC): 22
Refresh to Active (TRFC): 42
Bank to Bank CMD (TRRD): 3
Write Recovery (TWR): 6
Read-Write Command (TRTW): 3
Write-Write CS (TWTW_CS): 2
Write-Read Command (TWTR): 3
Write-Read CS (TWTR_CS): 2
Read-Read CS (TRTR_CS): 2
Read Data Transfers: 5
Memory Auto-Calibration
Read Data Transfer: Enable
Read Strobe Delay: Disable
Read Strobe Arrival: Enable
>FSB IO Strength
FSB IO Driving COntrol: Default
x 1X NMOS Strength
x 1X PMOS Strength
x 2X NMOS Strength
x 2X PMOS Strength
x 4X NMOS Strength
x 4X PMOS Strength
CPU Vid Control: 1.**v
CPU VID Special ADD: Auto
DDR2 Ram 1.8 Voltage: 2.25v
CPU VTT 1.2V Voltage: 1.**v
NB Core 1.2V Voltage: 1.**v
NB PLL 1.8V Voltage: *.**v
NB PLL 1.2V Voltage: 1.**v
NB PCI-E 1.2V Voltage: 1.**v
NB Core 1.2V convert from: *.**v
SB Core 1.2V Voltage: 1.**v
Clockgen Voltage: *.**v
GTL REF Voltage control: Enabled
CPU Core 1/2 GTL REF Volt: 48
CPU Core 3/4 GTL REF Volt: 48
North Bridge GTL REF Volt: 128
CPU PLL Setting Overide: Enabled
PLL Override loop count: AUTO
Conroe P-State Multiplier: x8
C1E Function: Disabled
[/HTML]
445FSB 4 hrs orthos ---465FSB 4 hrs Orthos----470FSB 4hrs orthos----480FSB 2 hrs orthos---478FSB 12hr Orthos---488FSB 2 hrs Orthos
http://img252.imageshack.us/img252/3...thosuz7.th.jpg http://img106.imageshack.us/img106/5...thosxb5.th.jpg http://img252.imageshack.us/img252/1...thoslk4.th.jpg http://img252.imageshack.us/img252/8...thosbg4.th.jpg http://img252.imageshack.us/img252/2...sprimh1.th.jpg http://img405.imageshack.us/img405/4...orhtof6.th.jpg
