Printable View
http://img211.imageshack.us/img211/6...2006062lb2.jpg
Compressor is TL3A 220V 50hz 102U
It is badass looking, not high effiency, but it is my first one.
I did smashed old fridge and took that thing out of there and my apartment looks like this after that. Sorry my bad english.:banana:
http://img245.imageshack.us/img245/5...2006061jq2.jpg
would be this insulate give some more effiency ? by insulating suction pipe and capillar pipe? or will it lower compressor run temps little bit?
http://img209.imageshack.us/img209/9...6062lb2ze3.jpg
yeah you should insulate :) !! dont know how much you'll get from it but its probably worth it !
i did spend 58 euros to some stuff for insulating and temperature monitoring :) pics caming more :D
good start, but it won't hold any earth shattering load, ie you'll have to pull down the res long be-for you start the computer up, and the temps will slowly rise from there.
i know its too small for 24/7 use but some benches it will be good enough...
i have insulated suction pipe almost and next i have to go buy big fan.
maybe it will run little bit colder.
this point i have reached. power of this machine 40 minutes cooling 27c water and now 20 c not bad becose 35 liter of fluid :D
http://img62.imageshack.us/img62/244...2006064np8.jpg
:lol: Love the shot with the fridge destroyed in your apartment.
hehe looks like you've had some fun :)
yes it was quite messed up :) my girlfrend was very,very angry when she did see that mess, she left at the same moment less than 5 second :DQuote:
Originally Posted by THE JEW (RaVeN)
that b****, what was she thinking :)Quote:
Originally Posted by KeZzZu
yeah! i reached below 10 c !! i insulated bottom of liguidbucket
Below 10C*
still with the same amount of liquid?
no i did pump 10 liters away :) system can't handle for 40 liters :/
update im getting to water frozing point now 4C' :D
some ice
Frozing point 4C'
Freezing point of Water is 0C (32F)
(In english you use Freezing when talking present, frozen when talking past ;) )
Let it chill all the water to 0, then add more, let it cool to zerro again then add more till it is full. Then let it freeze the water so the evap is a jiant ball of ice surounded by water. This way will take much time for temps to reach very high :)
ok, but i allready use glukol with water. water 30liter and glykol 10 liter :)
i did reacg 2 celsius not far away from 0 , and bucket did get heavy condensation, so i must insulate whole bucket. that i can reached my goal 0c temp :)
thnx for your advise
are those "load" temperatures. If they arent they are meaningless. Depending on how the system is tunned and assembled your load temperatures can be +50C.
as i did say , i dont use chiller for 24/7 system, but i use it for short benches like sp8m and sp32m nothing else. i just only drop water temps down to near 0C* and then start bench nothing more :) i know its too small even cool down 30 liters of liguid so it wont handle even overclocked 3700 sandiego only. if that chiller coll down liguid down to 2C* its enought to my benches then its has do his job :DQuote:
Originally Posted by epion2985
Ah, didnt realize that was the intended use. Carry on :up:
Love the shot of the smashed fridge. It looks like you took a Sledge Hammer to it!!!!
Ghettoo styylleee
Not bad at all for a cheap chill
lol, those are the funniest pics i've seen awhile. Looks pretty ghettoed :)
put a lot of ventilation on it! an when i say a lot i mean like all the fans that u have in yo home! then u may reach lower temps. i reach -36 on R12 in winter with no ventilation with a :banana::banana::banana::banana:y 140watt compr.
GHETTO VENTILATION!!!!
If you are refering to increasing airflow over the condenser then that is a double edged sword. You dont want too low of a condensing temperature as your pressures will drop with it as well, as will a smaller split hi to low side pressure wise you will be getting warmer temperatures not colder.