Printable View
I have a couple of pc-3200 1GB non-ecc dell memory sticks with the Micron Fatbody D9DQW ic's but need to reprogram them for pc2-4200 or higher to get them to work in my P5B-D. If anyone has please PM it to me or upload it and let me know. If you need more information please let me know.
I think that they can work fine without better SPD :D
What do you mean? They wont event boot at stock settings because my motherboard cant recognize pc-3200, they need to be pc-4200 and up.Quote:
Originally Posted by jmax_oc
Anybody have any dumps I can use, they have to be 1GB with D9DQW ic's.
I'm in the same boat as you.
Also, looking for D9DQW 1GB dumps :stick:
Thanks but already saw that thread, unfortunatly they have dumps for 512mb sticks not 1gb.Quote:
Originally Posted by periquitos
MACMAC, are you able to get your sticks to bootup at all? What motherboard are you using?Quote:
Originally Posted by MACMAC
I'll help if i can guys,i have 2 x 1gb patriot pc5600 xblk with D9DQW.You'll have to tell me what you want me to do though.
Check your PM Thickbrit.
I hope this works.
thanks, we will see if it works later today ! :)Quote:
Originally Posted by Thickbrit
Hey, I just opened your dump in Thaiphoon and it says 512MB modules :confused:Quote:
Originally Posted by Thickbrit
However, from what I can gather, it appears to simply be a Thaiphoon bug...
Must be,because they are 1gb sticks, pdc22g5600 xblk.
still looking for D9DQW 1gig stick dump
Quote:
Originally Posted by Supertim0r
Whats wrong with the one a couple posts above?
All sticks say that in Thaiphoon, if he took them off 1GB sticks, then they are 1GB dumps.Quote:
Originally Posted by MACMAC
I just didn't like the fact that they apparently default at 200Mhz/PC2-3200, but it will be tested tomorrow.Quote:
Originally Posted by MTP04
Finally I found some time to write a custom SPD for you guys.
If your modules match these specs, you are good to go:
Type: DDR-II SDRAM
Capacity: 1024MB
Configuration: 64M x 8
Ranks / Banks: 2 (Double sided)
Data Width: 64
Frequency / Timing Table
DDR-533MHz @ 3-3-3-10-15 (tCL-tRP-tRCD-tRAS-tRC)
DDR-667MHz @ 4-4-4-13-19 (tCL-tRP-tRCD-tRAS-tRC)
DDR-800MHz @ 5-4-4-15-22 (tCL-tRP-tRCD-tRAS-tRC)
Target IC
D9DQT, D9DQW, D9DRD, D9DQZ, D9DQR, D9DQP
Click here to download.
Load it to Thaiphoon Burner and fully rewrite the desired sticks with this SPD file.
http://www.armada.fi/Rhino/Rhino_Cus...body_CPU-Z.jpg
Thanks The Stilt ! :toast:
Ok, so the flash has been successful, and it does boot up wonderful at DDR2-800 5-4-4 at 1.8V :toast:
Now all we have to see is whether it will boot up in a P5B-Deluxe!
they won't boot on the P5B DX and P5W DH :(
well, this is MACMAC Fat Body :
http://simon.webideal.ca/Temp/Fat%20D9/fat2.JPG
http://simon.webideal.ca/Temp/Fat%20D9/fat3.JPG
stock memory :
http://simon.webideal.ca/Temp/Fat%20D9/1.JPG
http://simon.webideal.ca/Temp/Fat%20D9/2.JPG
http://simon.webideal.ca/Temp/Fat%20D9/3.JPG
mobo used to test/flash :
http://simon.webideal.ca/Temp/Fat%20D9/4.JPG
after :
http://simon.webideal.ca/Temp/Fat%20D9/5.JPG
Well we are all very confused.
No matter what SPD, timings, voltage these sticks will not boot in a P5B!
Will boot fine in a plethora of other motherboards, but just will not boot in an Asus :rolleyes:
Basically all out of ideas on my end!
I'm stuck with the same problems with these D9DQW's and my P5B Deluxe. Perhaps a bios update will help if someone tells Asus??
I'm absolutely sure a new bios would help, but I don't think Asus is going to allocate any resources to ensure compatibility for us "OEM" D9DQW owners, who represent a miniscule minority of users.
Perhaps someone could make a modified bios that'll work, if there's anyone here that knows how to do that. I don't think it'd it would take too much resources on Asus's part to fix this compatibility issue.
What motherboard were you able to get it to work with and how high can you push these sticks to at any specific voltage?
hmmm i can buy some D9DQW 1GB kit but after reading this it seems even after flashing they won't work right