Going for the single x1800xt class trifecta tonight

[chew*]

Hope to have some results in a bit card is at a nice frosty 10C idle, Mach 1 is running a tad colder with a fan in front, and a new bios for the Pure innovation board. Pray to the OC gods for high scores and no harware deaths.

[Coroner Kyle]

Good luck and you can do it!

[chew*]

Bad luck,,,,, Hose split in the cold........I knew it couldn't handle it but the home depot guy said it would be fine:stick: not to mention i was having some issues as to not knowing what some features in the bios are doing.......Back on stock cooler for now benches over for tonight but managed to pull off a 3d01 warmup run before luck went to crud..... >> http://service.futuremark.com/compare?2k1=8877860

[Geforce4ti4200]

only 15,000 marks to go. Your missing alot of tweaks by your low fps. I almost beat you in car high with 400Mhz less cpu?

[chew*]

only 15,000 marks to go. Your missing alot of tweaks by your low fps. I almost beat you in car high with 400Mhz less cpu?

now why would i try to break 3d01 with a dual core..........thats why i used it as a warmup.........no lod tweaks etc etc.....was going for 3d03,05,and 06.........already have the 3d06 record anyway.....

[Hicks]

only 15,000 marks to go. Your missing alot of tweaks by your low fps. I almost beat you in car high with 400Mhz less cpu?

There is a world out there, besides 3dmark 2001.

[ewitte]

Bad luck,,,,, Hose split in the cold........I knew it couldn't handle it but the home depot guy said it would be fine:stick: not to mention i was having some issues as to not knowing what some features in the bios are doing.......Back on stock cooler for now benches over for tonight but managed to pull off a 3d01 warmup run before luck went to crud..... >> http://service.futuremark.com/compare?2k1=8877860

Looks low. No messing with LOD. Just slightly higher clocks in nature.

http://service.futuremark.com/compare?2k1=8877860

[mascaras]

yep it looks a litle bit low , i have 34586 with a X800GTO and opty 148@3140 , no tweaks and no LOD


>> >> http://img368.imageshack.us/img368/1974/2k1novo5ew.jpg (http://imageshack.us)



with tweaks and LOD i got 35200 with same cloks , and 34700 olny with lod and opty onlly 3100 and lower clocks on X800 >> http://service.futuremark.com/compare?2k1=8861900


im waiting for a X1800XL too :)

[metro.cl]

http://img300.imageshack.us/img300/706/37025under3ghz3fz.jpg (http://imageshack.us)

and the link:
http://service.futuremark.com/orb/projectdetails.jsp?projectType=6&projectId=8869121

there you go 37k with cpu under 3ghz :)

[chew*]

Heh now try it with real rated pc 3200 @ 3-3-3-8 ddr 500.........show me what ya got........ 3d01 is memory bandwidth influenced, it was a warmup run(making sure cpu and memory stable)( you dont even know if my card was at stock) and i reitterate if i wanted a 3d01 record i wouldnt use dualcore or this memory.......nuff said...If ya want to derail the thread and try to impress take down my 3d06 record. OR you can just be considerate and say aww man bad luck better luck next time........

[payne280]

hope you get everything up and running, good luck

[Plywood99]

Sorry about your tubing chew*. Was that the cheapo depot vinyl tubing? I found for extreme cold temps silicone tubing works the best. Stays soft and flexible even down to -60/-70...

[chew*]

Sorry about your tubing chew*. Was that the cheapo depot vinyl tubing? I found for extreme cold temps silicone tubing works the best. Stays soft and flexible even down to -60/-70...


yah :( I been meaning to buy quality tubing but since chiller ain't running I keep putting it off....luckily no hard ware losses......shut it down instantly.
Where can i get that stuff?

[situman]

Chew did that grouper board of yours take another hit this time? Instead of drowning it to frying it to death, ur trying to take it down with an iceberg? LOL

[chew*]

Nah the line broke near the pump although I doubt the grouper would have even flinched. Just in case i always have my handy dandy Notebook nah just kidding Hairdryer close at hand though.

[Plywood99]

yah :( I been meaning to buy quality tubing but since chiller ain't running I keep putting it off....luckily no hard ware losses......shut it down instantly.
Where can i get that stuff?

http://www.mcmaster.com/

[chew*]

Temperature Range: -80° to +500° F

ouch at $5.95 a foot but then add a list of possible damaged pc components without it and its not half as bad. Thx for the linkage. There goes about $80 down the tubes (pun intended)

[Plywood99]

Which tubing you looking for chew*???

[chew*]

Which tubing you looking for chew*???

I looked at silicon hose's and looked for the lowest rated temp stuff 1/2 ID 5/8 OD at the site you sent me to. The sporlan chiller controller from chilly read -50 when it was working however it froze straight propylene glycol rated for -50 So the temp is probably innacurate and its actually colder. It now has R507 in it so it could/should get colder (It comes home tommorow)

[Plywood99]

How bout this one.

51135K41
(Same as 5236K45)
Silicone Rubber Tubing Soft, 1/2" Id, 5/8" Od, 1/16" Wall, White
In stock
Quantity Per Ft.
1-99 Ft. $1.24
100 or more 0.96

[chew*]

How bout this one.

51135K41
(Same as 5236K45)
Silicone Rubber Tubing Soft, 1/2" Id, 5/8" Od, 1/16" Wall, White
In stock
Quantity Per Ft.
1-99 Ft. $1.24
100 or more 0.96

hmmm ill check that out. luckily i didnt order yet.

[don_vercetti]

Heh now try it with real rated pc 3200 @ 3-3-3-8 ddr 500.........show me what ya got........ 3d01 is memory bandwidth influenced, it was a warmup run(making sure cpu and memory stable)( you dont even know if my card was at stock) and i reitterate if i wanted a 3d01 record i wouldnt use dualcore or this memory.......nuff said...If ya want to derail the thread and try to impress take down my 3d06 record. OR you can just be considerate and say aww man bad luck better luck next time........

errrr..to get the trifecta, will you not need the record in 3dmark01 as well? Or are you going for 03, 05 and 06.... :rolleyes:

[chew*]

errrr..to get the trifecta, will you not need the record in 3dmark01 as well? Or are you going for 03, 05 and 06.... :rolleyes:

yah 03,05,06 01 i just dont have enough cpu for....i already knew that.