My first tube! [Archive] - XtremeSystems Forums

Minusgrader

11-21-2005, 08:04 AM

Today I finished my first dry ice-tube.. What do you think?

http://kindstrom.net/upload/bygge/IMG_0391.jpg

http://kindstrom.net/upload/bygge/IMG_0389.jpg

http://kindstrom.net/upload/bygge/IMG_0390.jpg

http://kindstrom.net/upload/bygge/IMG_0394.jpg

http://kindstrom.net/upload/bygge/IMG_0395.jpg

http://kindstrom.net/upload/bygge/IMG_0405.jpg

http://kindstrom.net/upload/bygge/IMG_0580.jpg

http://kindstrom.net/upload/bygge/IMG_0572.jpg

http://kindstrom.net/upload/bygge/IMG_0575.jpg

http://kindstrom.net/upload/bygge/IMG_0588.jpg

http://kindstrom.net/upload/bygge/IMG_0584.jpg

http://kindstrom.net/upload/bygge/klar19oa.jpg

http://kindstrom.net/upload/bygge/klar28yl.jpg

http://kindstrom.net/upload/bygge/IMG_0924%20(Small).jpg

Before doing any more polishing, I tested the tube to make sure that it didn't fall apart when using it with some dryice. The LN2-can was empty so dryice was my only choise.

http://kindstrom.net/upload/bygge/IMG_0897%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0905%20(Small).jpg

Sucess! It didn't fall apart!

http://kindstrom.net/upload/bygge/IMG_0907%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0910%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0914%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0919%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0920%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0921%20(Small).jpg

http://kindstrom.net/upload/bygge/botten.jpg

That's all! Give me some comments or questions!

My SECOND container:

http://kindstrom.net/upload/bygge/IMG_0967%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0968%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0980%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0981%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1010%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1011%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1012%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1013%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1015%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1016%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1018%20(Small).jpg

Allmost done! :)

http://kindstrom.net/upload/bygge/IMG_1028%20(Small).jpg

Finished :)

http://kindstrom.net/upload/bygge/IMG_1036%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1041%20(Small).jpg

marvt74

11-21-2005, 08:09 AM

Gotta hate people with access to all that machinery ;)

Looks beautiful dude cant wait to see how it performs

Tribal84

11-21-2005, 08:16 AM

beautiful man :)
looks really nice

Ratax

11-21-2005, 08:31 AM

Very nice!
Hope you got some good results, please let us know ;)

With that machine it's not suitable do the container in just one piece, right?

[krook]

11-21-2005, 08:45 AM

Vad kostar de? :D

For those who're not swedish: What do they cost?

k|ngp|n

11-21-2005, 08:46 AM

Beautiful job!! :toast:

Minusgrader

11-21-2005, 08:51 AM

Thanks for allt the comments. Glad you liked it :)

']Vad kostar de? :D

Hmm.. Det röret du ser på bilden har gått för 400kr inkl. isolering och monteringsdetaljer. Nästa flyger för samma pris det med ifall det inte blir några större förändringar som drar upp materialåtgången.

godmod

11-21-2005, 09:25 AM

and now for those who do NOT understand swedish? ;)

marvt74

11-21-2005, 09:33 AM

Not sure all i could understand from his post was 400kr which is about 40euros

Minusgrader

11-21-2005, 10:09 AM

With that machine it's not suitable do the container in just one piece, right?

Sorry, missed to answer your post. Well... I don't want to try. It's to small I think. Our bigger machine can do it for sure. It's possible to do "by hand" also. I've done an oiltank (not copper offcourse) for a truck or something and it was just like a mousepot before the "top" was welded on to it.

Not sure all i could understand from his post was 400kr which is about 40euros

Hehe. You're right. It's about 40€ (40.88€ exactly).

zightx

11-21-2005, 11:55 AM

Hehe, I'm gonna get that tube. :D :woot:

Looking forward to see it in action. ;)

SlackeR

11-21-2005, 01:20 PM

Are you planning on making a lot?
I might be interested sometime if they prove efficient :)

Dani

11-21-2005, 01:55 PM

You should cut these black lines with something, cold aceton will "flow" better over whole bottom :toast:
If you do that, I buy one and you gonna send me on of those pots (Finland/Helsinki) :fact:

http://koti.mbnet.fi/dani69/Kuparikipot/IMG_0588.jpg

[krook]

11-21-2005, 04:58 PM

Thanks for allt the comments. Glad you liked it :)

Hmm.. Det röret du ser på bilden har gått för 400kr inkl. isolering och monteringsdetaljer. Nästa flyger för samma pris det med ifall det inte blir några större förändringar som drar upp materialåtgången.

Tar det på engelska så slipper vi översätta. :stick:

Oh ok, not that expensive, think I'll keep my old Ln2 container though. I was just curious. I only use it like once or twice a year anyway. Looks great but I think you can do some improvemets on the bottom. Good job!

Edit: maybe cone shaped?

PkG.1337

11-21-2005, 08:49 PM

professional

Minusgrader

11-21-2005, 11:23 PM

Are you planning on making a lot?
I might be interested sometime if they prove efficient :)

I'm planning to do as many as I have to ;)

You should cut these black lines with something, cold aceton will "flow" better over whole bottom :toast:
If you do that, I buy one and you gonna send me on of those pots (Finland/Helsinki) :fact:

Sure, it's possible to do. I can try it today hopefully.

Dani

11-22-2005, 03:33 AM

Sure, it's possible to do. I can try it today hopefully.

:toast:
Med isolering och allt som behövs att spänna röret ner för 40€ + shipping? :)

Put some pics today if you have time to do that to bottom what I posted, then we can PM and I will give my contact information to you :banana:
:toast:

Ratax

11-22-2005, 03:48 AM

Are you planning to do a GPU version as well?
I maybe be interested...

Minusgrader

11-22-2005, 07:30 AM

:toast:
Med isolering och allt som behövs att spänna röret ner för 40€ + shipping? :)

Put some pics today if you have time to do that to bottom what I posted, then we can PM and I will give my contact information to you :banana:
:toast:

Ja, precis. 40€ för allt som behövs till röret.

I couldn't do a base like that today because we hade no tools suitable for that job. But... Hopefully we have next week ;)

Are you planning to do a GPU version as well?
I maybe be interested...

Yes I am. I'm doing one for myself (as a test) whenever I have the time.

Entsafter

11-22-2005, 12:48 PM

Very nice tube and really cheap :D

babyelf

11-23-2005, 05:42 AM

awesome work there :D

M.Beier

11-23-2005, 07:49 AM

Looking forwards to receiving mine :D (We're 3 danes that've ordered as far as I know :D)

Can you try putting a 200W load underneath and see what temps it'll do on DICE ? =)

Minusgrader

11-23-2005, 08:08 AM

Looking forwards to receiving mine :D (We're 3 danes that've ordered as far as I know :D)

Can you try putting a 200W load underneath and see what temps it'll do on DICE ? =)

zightx is going to test his one next week I think. Personaly I don't have anything good to test it with. My rig i f*cked.

M.Beier

11-23-2005, 09:00 AM

Nå oki, fair nok :)

Hvor meget vejer rørene og hvilke dimensioner har de lige pt.?

Minusgrader

11-23-2005, 09:13 AM

Nå oki, fair nok :)

Hvor meget vejer rørene og hvilke dimensioner har de lige pt.?

I hope I understand what you asked... (Danska är inte min starka sida)

Weight:
About 1kg without insulation and stainless plates

Pipe-dimensions:
Inner diameter: 50mm
Outer diameter: 54mm
Length: ~310mm with base (not exakt because i get the pipes cut to 300mm and often they are cut in an angle so i have to fix that)

Base:
Thickness = 14mm

.sentinel

11-23-2005, 09:31 AM

The base thickness might be a little to much. I think the recommanded amount is around 6mm.

Minusgrader

11-23-2005, 11:03 AM

Sorry, the base is 14mm from bottom to top. The "circels" go down to 10.25mm.

6mm? No way?

SlackeR

11-23-2005, 01:55 PM

VERY nice work i must say.
I think i will be buying one sometime.. At that price it's a steal.

.sentinel

11-23-2005, 03:14 PM

Sry I misread it must be atleas 6mm

T_M

11-23-2005, 06:04 PM

Arent there rules about speaking in english?

nhenhophach

11-23-2005, 09:43 PM

Wow beautiful..

Minusgrader

11-23-2005, 11:11 PM

Arent there rules about speaking in english?

I could not see anything about that in the rules, but I will stick to english from now on. Swedish only in PM's! Sorry

kappa2001

11-24-2005, 06:23 AM

hey after seeing the tests i might be interested in that :p
can anyone estimate (guess :p) how much it would cost to send something like that to Portugal?

zightx

11-26-2005, 03:48 AM

hey after seeing the tests i might be interested in that :p
can anyone estimate (guess :p) how much it would cost to send something like that to Portugal?

Just check with UPS. :)

[XC] leviathan18

11-26-2005, 04:23 AM

Minusgrader

11-26-2005, 07:00 AM

minusgrader....

im going to have access to a cnc machine @ university so i want to make ln2/dyce container can you help me with the design ?

:toast: really beatiful container you got sad i just have aluminium :(

Thanks!

What do you want me to help you with? The CNC or designing the whole base? Send me a PM.

MeltedDuron

11-26-2005, 07:18 AM

Amazing work, great price... You should make a chipset pot! :toast:

charlie

11-26-2005, 05:39 PM

awesome!! Just wish they were here in the states.

C

Shinuza

12-01-2005, 08:31 PM

Nice doing there.
I noticed you used a paste to make the base shine.
That's useless, better result is coming from using a very thin sandpaper and sweating ;)

When using paste you let a thin layer on the base, it's interfer in the thermal conductivity.

Minusgrader

12-01-2005, 10:52 PM

harleybro

12-01-2005, 11:47 PM

First of all nice tube design. :toast: Has any testing or runs been done with one of these tubes yet if so can you post some results in your thread? As for the paste. I have used buffing compound (paste like) on my mousepor for final shinning but clean it off with acetone after so have hed no issues with residue. ;)

GOESA

12-02-2005, 03:33 AM

First of all nice tube design. :toast: Has any testing or runs been done with one of these tubes yet if so can you post some results in your thread?

Sure harleybro, I will be reciewieng 3 of these tubes as soon as they are done, then I will ship two of the tubes to JacobHansen from this forum and M.Beier, they are probaly gonna test the tube the following weekend, after they recived it.. Jacob on some FX5x (Not sure if its FX55 or FX57 :stick: ) and M.Beier on a 3700+.

/Grau

Grave

12-02-2005, 04:42 AM

awesome job man.

Shinuza

12-02-2005, 04:56 AM

I don't use a paste for the base. But I do use it for the rest of the tube.

Ok :stick:
Your picture just misled me :p:

zightx

12-02-2005, 09:02 AM

I received my tube yesterday. Very nice! :woot: But the tube hade oxidated a little bit. Gonna polish it with some more autosol soon.

Thanks Fredrik! (Minusgrader) :banana: :banana: :banana:

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40617

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40618

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40619

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40620

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40621

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40622

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40623

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40624

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40625

http://www.xtremesystems.org/forums/attachment.php?attachmentid=40626

zightx

12-02-2005, 09:05 AM

Some more pics. :woot:

Entsafter

12-03-2005, 04:57 AM

Is it possible to fill the tube with LN2 or will the tube fall apart?

SlackeR

12-03-2005, 05:46 AM

Very nice - but is that holddown made of metal?

M.Beier

12-03-2005, 05:57 AM

Is it possible to fill the tube with LN2 or will the tube fall apart?

Shouldnt change a thing, so I guess so :)

zightx

12-03-2005, 07:11 AM

Is it possible to fill the tube with LN2 or will the tube fall apart?

Why should it fall apart? Do you think he's making crappy tubes? :stick:

I'm gonna test it with DICE or LN2 next weekend. :fact:

perry_78

12-03-2005, 07:13 AM

Feel like sending one in over to Denmark any time soon :D I know there are aplenty who would like one for a reasonable price ;)

M.Beier

12-03-2005, 07:26 AM

Feel like sending one in over to Denmark any time soon :D I know there are aplenty who would like one for a reasonable price ;)

Already been ordered from Denmark, SlackeR, Try-This & Zalam is considering buying as well, they'll be ordering lateron, you can visit www.ocinfo.dk and buy a piece together with them (saves some @ shipping)

perry_78

12-04-2005, 04:41 AM

Alright, oc.dk will have some cool results it looks :)

M.Beier

12-04-2005, 05:36 AM

hehe, I doubt it'll be for oc.dk.. :)

Ocinfo.dk and oc.dk aint the same thing :|
But I'll might be surprised :)

Nanometer

12-04-2005, 10:03 PM

wow, beaituful tube!

M.Beier

12-05-2005, 02:11 PM

Wuhuu just received info - In case nobody puts up results in this week, I'll do on saturday ;) (uhh, pray'n that my CPU aint got tha cold bug :( )

SlackeR

12-05-2005, 02:45 PM

I am worried about the metal holddowns.
It would be better to make the top part of plastics.
A cutting board is nice ;)
But on the other hand.. For that price you can't complain :)

Dani

12-10-2005, 09:33 AM

What's up here?
Any news?
Updates?

Minusgrader

12-10-2005, 09:55 AM

What's up here?
Any news?
Updates?

This month we have our OC-championship in Sweden, I'm working on both my own things and these tubes. Because you ask, I give you some pics of the process were I make my own personal DI/LN2-container for the championship.

NOT FINISHED!!!! 5 more mm to cut on the inside and 10mm on the outside..

http://kindstrom.net/upload/bygge/IMG_0967%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0968%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0980%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_0981%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1010%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1011%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1012%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1013%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1015%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1016%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1018%20(Small).jpg

http://kindstrom.net/upload/bygge/IMG_1028%20(Small).jpg

speed bump

12-10-2005, 10:34 AM

Nice tube there

G H Z

12-10-2005, 03:16 PM

The solid one is looking very good :)

lawrywild

12-10-2005, 04:58 PM

can I buy one in UK, i'm VERY VERY interested in one for 40euros :slobber:

Minusgrader

12-13-2005, 07:18 AM

Thread updated with pics of the completed solid container. See first post.

lawrywild, sure you can.. But I don't have the time to build a container for you right now.

ilkkahy

12-13-2005, 08:10 AM

Will you start producing those solid aluminium versions for others too? My guess they might sell pretty well. Completely flat bottom (similar to copper version) might also increase performance a bit. Really nice work!

Hugo van Dijk

12-13-2005, 11:48 AM

My guess they might sell pretty well.

Oh yeah defantly :slobber: :slobber:

lawrywild

12-13-2005, 01:42 PM

lawrywild, sure you can.. But I don't have the time to build a container for you right now.

ok, well if u ever have the time, PM me but I'll keep an eye on this thread anyway..

MeltedDuron

12-14-2005, 07:40 AM

how much for a solid copper one? :slobber:

Minusgrader

12-14-2005, 09:38 AM

how much for a solid copper one? :slobber:

Not for sale. :fact:

k|ngp|n

12-14-2005, 10:19 AM

Love the pics! :toast:
Tube is looking nice too.

Minusgrader

12-14-2005, 10:40 AM

I have done some testing with the solid one.. I can't tell anything about the temps, but they were 100% stable with a Celeron D running at 1.75V. The thermometer-thing I used were not showing the real temp, but it was rock solid at the lowest temp.

http://kindstrom.net/upload/monterat1.jpg

http://kindstrom.net/upload/is.jpg

http://kindstrom.net/upload/upnrunning.jpg

http://kindstrom.net/upload/roek.jpg

Result:
http://valid.x86-secret.com/cache/56703.png

Malachia

12-14-2005, 11:36 AM

really nice overclock!

EDIT

can you tell me how you do to solder the "bigger" part( dedicated to block encluster) perfectly perpendicolar? and what you used?

http://kindstrom.net/upload/bygge/klar28yl.jpg

lawrywild

12-14-2005, 12:28 PM

100% overclock club ;)

I want one so much now lol.. when you reckon you might find the time to build one (and how much for one of those aluminium ones?)

M.Beier

12-14-2005, 12:43 PM

Looking good :)

Hehe, tørris - in danish tør = dry, but ris = rice :D - dryrice, now thats a superpack, but for children in africa :P

SlackeR

12-14-2005, 03:34 PM

Maybe very small pellets? :D
I like your tubes. They are looking good. I love Bling Benching :)
And i see you use an SLK-900a. Lovely cooler ;)

NiclasS

03-10-2006, 05:52 PM

I just love those Freud! I hope to make one my own sometime :)

FireDragon

03-25-2006, 05:55 PM

This is an english forum only no spanish!! (saving ur @sses b4 the modds c)

BTW good job there man keep up the good work.

Dragon

PS i didnt read the whole thread so if someone else told u srry.

Crazy Chuckster

04-05-2006, 08:55 AM

Very nice machine work

K404

04-06-2006, 02:20 PM

Thats excellent work at an excellent price!

If its not too much hassle, I may ask you to make a DI tube for me sometime when you arent too busy, if thats ok :)

Kenny

bullet2urbrain

04-06-2006, 05:33 PM

what is the secret... i would LOVE To know where to get the pricing you got on those metals.... i must really be missing something because every block of Cu or Alu i see is like 200 + USDollars. the copper more like 330 USDollars.

Thanks btw excellent work, how did you arrive at the design for the base?

M.Beier

04-28-2006, 04:14 PM

It worked well, got very cold, sadly I dont know how cold, but it sure has one weekness, the metal holddown, it gets totally frosted up within 1 sec :S

You can find results with tube here (http://www.xtremesystems.org/forums/showpost.php?p=1422778&postcount=2057)

drcooling.cl

04-29-2006, 05:07 AM

Hey minusgarder. Can you consrtuct this?

http://img137.imageshack.us/img137/812/highperformance9zq.gif

Soldier within a copper tube must go with TIG (perfect for n2l). It is possible to be constructed with a circular saw mounted on metallic bar in the CNC

Like this, but of only 1 disc :stick:

http://www.drcooling.cl/coppermine/albums/OtrosWaterblocksDrcooling/CNC_021.jpg

ilkkahy

04-30-2006, 09:19 PM

I think you could make it with steel-band saw. I have made bit similar ln2 container with an angle grinder so i couldnt quite get as dense lamels :rolleyes:
http://koti.mbnet.fi/ilkkahy/ln2&co2%20kupit/ln2%20container%201.jpg

forey

04-30-2006, 10:13 PM

Beautiful containers mate

drcooling.cl

05-02-2006, 07:33 PM

I am constructing one in milling CNC. The schematic is optimized for dry ice.
The relation between height and thickness is important. Also it is important the thickness of the base and the contact surface.

Minusgrader

05-03-2006, 05:19 AM

GOATSLAYER

08-02-2006, 09:08 PM

I envy your access to that machinery.

Beautiful work.