View Full Version : 1800+ @ 1752MHz @ 31c full load
stompah
05-25-2002, 04:14 PM
KK266-r
1800+ AGKGA
256MB pc133 cas2 Crucial
30g 5400rpm Western digital HD
Radeon 32MB DDR LE
600grit lapped Alpha PAL6035 w/ 7500rpm Delta fan.
Room temps at 61f. At a room temp of over 80f CPU never exceeded 40c gotta love 7500rpm fans!
I deleted the other thread cause Smiz was correct I was trying to upload it as a .bmp file. converted it to .jpg. I usually do things correctly but this time I dropped the ball.
Hardass
05-25-2002, 04:27 PM
Looking Good.:D
1752 is one thing, but keeping the temps below 40c! Sweet! Great Job
stompah
05-25-2002, 04:50 PM
I need to volt mod the board and swap in the AGOGA... old CPU IN AGKGA
stompah
05-25-2002, 05:09 PM
Originally posted by JAWS
1752 is one thing, but keeping the temps below 40c! Sweet! Great Job
hehe should I shoot for temps below 30c? hehe any suggestions? I could rig the system up right in front of the A/C hehe
Hardass
05-25-2002, 05:13 PM
Originally posted by stompah
hehe should I shoot for temps below 30c? hehe any suggestions? I could rig the system up right in front of the A/C hehe
I would be real happy with those temps. But there is always something to shoot for!:D
DaGooch
05-25-2002, 05:25 PM
Yes, very low temperatures for air cooling. :D
Originally posted by stompah
I need to volt mod the board and swap in the AGOGA... old CPU IN AGKGA
My AGOGA overclocked better undervolting! That was good, since I could never get my temps under 40c. I think the AK35 temps are a little off though!
Hardass
05-25-2002, 06:04 PM
Originally posted by JAWS
My AGOGA overclocked better undervolting! That was good, since I could never get my temps under 40c. I think the AK35 temps are a little off though!
On my shuttle the bios temps were right on with MBM. But my dd5 temps with a probe touching cpu reads 3 to 4 degrees higher.
I think some boards are different. I had the same readings with 1.6 as I did with 1.95. I thought about putting a little piece of tinfoil on the cpu temp diode! :p
DaGooch
05-25-2002, 06:15 PM
What sucks is that there is like only 2 boards at present that read the "real" temperature of an XP which would be the internal diode inside the CPU. You would be surprised how hot the inside of an Athlon XP is. ;)
Hardass
05-25-2002, 06:16 PM
Originally posted by JAWS
I think some boards are different. I had the same readings with 1.6 as I did with 1.95. I thought about putting a little piece of tinfoil on the cpu temp diode! :p
That is strange, if i raised it the temps would rise right away.
Hardass
05-25-2002, 06:18 PM
Originally posted by DaGoochMeister
What sucks is that there is like only 2 boards at present that read the "real" temperature of an XP which would be the internal diode inside the CPU. You would be surprised how hot the inside of an Athlon XP is. ;)
I think I,ll switch the dd5 from the 1600 to the 2000, just to be safe!
stompah
05-25-2002, 07:34 PM
Unfortunately the AGOGA 1800+ does not post at 152MHz fsb :( I am very disappointed. I hope some burning in fixes the problem.
JBELL
05-26-2002, 01:37 PM
Originally posted by JAWS
1752 is one thing, but keeping the temps below 40c! Sweet! Great Job
easier said than done!!! living in the desert kicks my ass!!!
swiftech mcx462 with delta 68cfm I still run 44c full load after 2 weeks of 100% full load
JBELL
05-26-2002, 01:38 PM
Originally posted by stompah
Unfortunately the AGOGA 1800+ does not post at 152MHz fsb :( I am very disappointed. I hope some burning in fixes the problem.
mine gets touchy about there too!! grrrrr
stompah
05-26-2002, 02:46 PM
Originally posted by JBELL
easier said than done!!! living in the desert kicks my ass!!!
swiftech mcx462 with delta 68cfm I still run 44c full load after 2 weeks of 100% full load
you need my air conditioner :D
Originally posted by JBELL
easier said than done!!! living in the desert kicks my ass!!!
You and me both! You have that dry heat and I have the wet! ;)
Hardass
05-26-2002, 04:48 PM
Originally posted by JAWS
You and me both! You have that dry heat and I have the wet! ;)
Yes and it is a nasty wet heat too!
Smizack
05-26-2002, 07:32 PM
Originally posted by stompah
you need my air conditioner :D
Yup, Mines running at 20.4c right now.
With a full load it gets to around 25-27c.
Hardass
05-26-2002, 07:53 PM
Originally posted by Smizack
Yup, Mines running at 20.4c right now.
With a full load it gets to around 25-27c.
What cooling setup you running?
Smizack
05-26-2002, 08:42 PM
Originally posted by Hardass
What cooling setup you running?
A crappy HSF. Untill I get JBell's Heatpipe.
This is what's sitting on it now. (yeah, I know. Bleh!)
Hardass
05-26-2002, 08:47 PM
Originally posted by Smizack
A crappy HSF. Untill I get JBell's Heatpipe.
This is what's sitting on it now. (yeah, I know. Bleh!)
Bro those are some low temps for a stock hsf,
Smizack
05-26-2002, 08:51 PM
Originally posted by Hardass
Bro those are some low temps for a stock hsf,
Yup. It's called A/C power!;)
With the a/c off I idle at 35 or so and max out at 41 with a full load.
Hardass
05-26-2002, 08:59 PM
Originally posted by Smizack
Yup. It's called A/C power!;)
With the a/c off I idle at 35 or so and max out at 41 with a full load.
You wear a coat when your on the comp, my computer room is 78f and my temps run 38c folding. And i,m running a pal 8045 and delta
DaGooch
06-11-2002, 09:20 PM
Originally posted by Smizack
A crappy HSF. Untill I get JBell's Heatpipe.
This is what's sitting on it now. (yeah, I know. Bleh!)
Is that a motherboard chipset heatsink and fan? ;)