The Official Opteron 939 Overclocking Thread

[dogsx2]

I have got the same stepping here:

148 0536GPMW 0189er Batch

(not so nice as my 144, but really 3GHz)

free

Yea, my 144 is the better then my 146 & 148 for doing 3GHz at low volts. Lets see a tweaker of your 148, what ram?

[freestylercs]

Yea, my 144 is the better then my 146 & 148 for doing 3GHz at low volts. Lets see a tweaker of your 148, what ram?


Corsair TwinX LL Platinum 1.1 old BH5.

goes up to 270MHz@3,6V (look at sig).

free

[F|apDro|`]

aiit folks, got the 32m prime stable. upped ram voltage to 2.75v and also tried a diff combi of VID and % to get where im at of about 1.55 avg.... gosh i hate neo2 fluctuating vcore.

http://img478.imageshack.us/img478/7306/29pistablefullscreen5pv.th.jpg (http://img478.imageshack.us/my.php?image=29pistablefullscreen5pv.jpg)

as it stands now im done for tonight. gonna start a prime blend test? i guues thats the best to do and let it run till morn. should be a good 7 hours and hopefully it runs thru the night. *wish me luck!

im pretty sure im pumpin a tad bit more volts than is actually necessary to be stable but its just in an effort to compensate for the wildy fluctuating voltage courtesy of the neo2. *sigh.

I know what you mean with the neo2... I have the same :slapass:

[Jesus]

what do you guys think of this one?
CABYE 0530 GPMW
Opty 146

[nf4]

^^^^seems to be a good one if you read a few pages back i am sure you will some results

[Jesus]

Just to get sure before I place my bid on ebay :D

[ozzimark]

here's something weird for you guys. my 146 is doing quite well, but something is perplexing me. i can get to 2.9ghz with 1.4v or 3ghz with 1.45v prime95 small fft stable. no matter what i do to the vdimm, timings, or memory divider, superPI 32m will fail at those speeds. i'm guessing the limiting thing on this chip is the memory controller portion that runs at cpu speed. anyone know of ways to get around this.. issue? :D

[periquitos]

Then start your own thread just for MaxTcase. There is no sense of trashing up an oc thread with that. Someone who just gets an opty or is new to the forum and wants to find out about how the opty's oc shouldn't have to go thru a lot of MT posts to find oc info. This tread has pasted up the venice, sd and x2 threads is a short time. Please don't trash it up.

periquitos, your new here, please respect other people threads. If MT is that important to you, start your own thread. Don't hijack. :nono:
:eek:


Yes , I do know...

but... even being a new member I do really know what "smiles" matter. Look again at my repply and you see that :fact: ... And I really don´t understand why you came to me with this attitude... Maybe just because you don´t like MT? Because you don´t believe MT? I´m sorry if you don´t agree... but I do. I will not create another thread , someone sugested that we can put Mt together with overclock screenshots , that´s a good ideia ! :toast:


:) :) :)

[Ugly n Grey]

@ ozzimark bump the voltage and try raising or lowering the data drive strength in your BIOS.

@ the two guys grumbling at each other... MT is a part of an OC, if you want to post it go ahead. Be nice.

[ozzimark]

@ ozzimark bump the voltage and try raising or lowering the data drive strength in your BIOS.
a step ahead of you. i know changing vcore definitly does wonders, as i got ~100mhz from a .05v increase. raising drive strength did nothing.. and it seems that lowering didn't do much either :(
i'll play with bios 704-2BTA when i get back from class, maybe it'll do something unexpected. either way, i feel that i definitly have a ton of headroom in this cpu :toast:


edit: oh.. data drive strength? quick! time to try
nope, was using level 1 before. 3 seems worse. try 2 real quick

[foofreaknfighte]

Then by all means you need to have your computer prime stable. I am fine at 32m or OCCT stable. I am not trying to make you uncomfortable by saying you should just be doing 32m or OCCT, please don't make me uncomfortable by saying I should do prime.


Believe me, I am not trying to make anyone uncomfortable. :D In fact I would like someone to make me comfortable with just pi or OCCT, cus it looks like prime aint gonna happen at these speeds....which will make me easy to convince ;)

Anyone have an stats on 3Dmark yet at diffent OC's? I noticed that I lost about 1000 cpu score points going from 2.8 to 3.oghz. Interested to see what other people have been doing. I will post screenshots later regarding this.

[0verl0ad]

144 @ 2835MHz / Infineon 6A 2x256 MB @ 257MHz 2 2 2 5 / Lukü / IHS yes

http://img453.imageshack.us/img453/7886/superpi289840gw.th.jpg (http://img453.imageshack.us/my.php?image=superpi289840gw.jpg)

Is this a good resault for my PC?

[gundamit]

Here's one I did this morning with my 2gig set of Patriot Infineons.

http://img216.imageshack.us/img216/2449/300x113nh.png

I found my original 32m stable screenie with my TCCD. Not sure if I ever posted it.

http://img412.imageshack.us/img412/9890/300x114lz.png

[HermS]

Very nice Gundamit, especially with low voltage too! :toast:

[el rolio]

here's something weird for you guys. my 146 is doing quite well, but something is perplexing me. i can get to 2.9ghz with 1.4v or 3ghz with 1.45v prime95 small fft stable. no matter what i do to the vdimm, timings, or memory divider, superPI 32m will fail at those speeds. i'm guessing the limiting thing on this chip is the memory controller portion that runs at cpu speed. anyone know of ways to get around this.. issue? :D

yea im in need of this info too. whats up with mem controller man. i wont even try to go prime small stable till i get the frikken memorynecessary super pi done with

[ozzimark]

yea im in need of this info too. whats up with mem controller man. i wont even try to go prime small stable till i get the frikken memorynecessary super pi done with
i remember there being a board somewhere that allowed for the change of the memory controller voltage seperate from the cpu. i didn't think such a thing was possible.. but it was there. i wonder if it's possible to do a mod on the dfi nf4 to do that. :stick:

[t-max]

wooooot i just pop´ed the IHS gave me a stunning 12C temps drop.

all other conditios where as before just 20min later and my chip is priming at 45-47 C instead og 57-59C :banana:

same v.core and evry thing

it gave me 80mhz more primestable.

[shimmishim]

now that's what i like to hear t-max! :)

with only 1.45 volts at 2.7 ghz, my chip runs 52C's load!!!

it'd be nice to see a 10C drop :)

[sauria]

Is there no contact with the core or thermal goog on your IHS t-max?

[ozzimark]

Is there no contact with the core or thermal goog on your IHS t-max?
i dunno what his deal was, but i'm pretty sure both of my ihs's are connected pretty well.. i get 40c load with 1.5v on both my 144 and 146. it would be fun to detatch it, but after what happened to my newark, i don't feel like killing another cpu. maybe detatch, reapply thermal paste and use silicone to put it back on. someone would have to advise me on how to get the IHS back on flat though.. i'm thinking goop it up and stick it in the socket and carefully put a heatsink on it to maintain good contact as it dries

[gundamit]

Very nice Gundamit, especially with low voltage too! :toast:Yeah. But look at the volts to get to 3.4ghz. Looks like the end of the road. Still I can do 3D a little higher. Prime I'm guessing will be between 3.2 and 3.3ghz. At least I managed to close the gap a little bit with Sierra's CPU.

http://img476.imageshack.us/img476/5681/309x113nm.png

[Richdog]

Got my friend nightic to order me a 146 from Monarch in the U.S. via a contact... hope it turns out to be good. I got 2.7ghz stable out of this CABGE at ~1.7v... any more and it was running to 1.75-1.8v to stay stable... way too toasty. :)

[ozzimark]

i think i'm gonna blame max async latency and read preamble

[gundamit]

Gun your 32m is like afIr3wIthIn :(

its really bad should be 21m range easy Yeah. I'm just going for a stable shot. I can tweak it a bit to bring down the time, but the focus right now is just finding the top end of the CPU. Heck, I'd throw a bigger divider at it just to get the clocks up 1mhz. :D I'll save the SuperPi tweaking/tips and tricks for later. Wouldn't be running 2x1gig if I were just going for SuperPi times. Although any suggestions are always welcome. :D

[gundamit]

oh, hehe thought that was tweaked was like wow somehtings not right :)

nice clocks on that I hope my 148 I have coming can do thta on my mousepot ;) I'm sure with a halfway decent Opty the King of the Mousepots will go even farther. :up:

[el rolio]

now that's what i like to hear t-max! :)

with only 1.45 volts at 2.7 ghz, my chip runs 52C's load!!!

it'd be nice to see a 10C drop :)

QFT and AGREEMENT! ha

[kleimo]

Hi,

I have tryed to get my opteron 144 CABNE 0530APMW over 3GHz to Pi but no luck. 2.9GHz is the farest that it will Pi, 32m goes but OCCT wont. Giving volts over 1.4v just makes it worst cant even Pi 2.9GHz :( . My cooler is TT big typhoon. Mems are OCZ 3200 VX 2x512mb. I´m not sure that my memory settings are correct or is the cpu at its max.?? Sorry my bad english :). PI 8m pic. (http://www.kleimo.pointclark.net/kuvia/oc/3000+_opteron/2.9GHz_1.4v_8m.jpg)

[t-max]

Is there no contact with the core or thermal goog on your IHS t-max?

The wierd thing is there where percekt contagt beween the core and IHS, but i still reciived this huge gain by pulling it of, i can take a hell lot of more v.core this way i bumped the v.core from 1,60 to 1,66 and i still have a load temp under 48 C :banana: inspite of my roomtemp at 24,5 C

Here are some results after the removel:
-T.ambien 24,5C (roomtemp)
-Watercooling

i made a 32M run 100% stable evry time at 3100mhz heres a mu result at 3110 mhz :

23m 18,281s with spi 1.4 non sse3

[nf4]

some sad news when i came home today the dreaded yellow note of death was on my door saying that they will redeliver on monday even though i live nextdoor to ups bla these guys better call me back and let me come pick it up i was 30minutes late from the ups or the ups was 30 minutes early i forgot which bla

[shimmishim]

wow. i'm so glad i pulled my IHS.

I am down from 64-66C's load to 55C's and I can run OCCT now longer than I could before. I just need to tweak some more. :)

yay!

[aicjofs]

This IHS thing has me really interested too.

Radiator inlet temp(return from CPU block) is 27.7C with a contact temp probe and the water block underside is 28.5C, yet my full load temps are 45C. For this test the CPU is 1.4V at a conservative 2600Mhz. From my experience with this particular water cooling setup with a Venice and Winchester, shoot even with a Prescott that number is 5C too high to me. I have reset the waterblock at least 5 times.

Maybe it's the Neo4 BIOS?

[sauria]

The wierd thing is there where percekt contagt beween the core and IHS, but i still reciived this huge gain by pulling it of, i can take a hell lot of more v.core this way i bumped the v.core from 1,60 to 1,66 and i still have a load temp under 48 C :banana: inspite of my roomtemp at 24,5 C

Here are some results after the removel:
-T.ambien 24,5C (roomtemp)
-Watercooling

i made a 32M run 100% stable evry time at 3100mhz heres a mu result at 3110 mhz :

23m 18,281s with spi 1.4 non sse3
Thanks, an interesting result -- makes me want to remove mine too.

[sauria]

144 @ 2835MHz / Infineon 6A 2x256 MB @ 257MHz 2 2 2 5 / Lukü / IHS yes

http://img453.imageshack.us/img453/7886/superpi289840gw.th.jpg (http://img453.imageshack.us/my.php?image=superpi289840gw.jpg)

Is this a good resault for my PC?
Ist gut! I want one of these

[airwolves]

Right now i'm 38c at 11x250 at 1.36v.. This thing just keeps amazing me how much faster it is than my x2 4400

Now I just need to find out whats with my temps. It shows 38c then when running cpu intense program or benchmarks it jumps to 45 to 49c in less than a sec.. Guess I need to check the contact or is this normal??

[dinos22]

144 @ 2835MHz / Infineon 6A 2x256 MB @ 257MHz 2 2 2 5 / Lukü / IHS yes


Is this a good resault for my PC?
overload.............what's this infineon 6A stuff........look at the speed and timings damn

[laydback]

Ordered my 146 yesterday from e-Wiz and looked today and they are no longer offering it. Wonder if I got the last one...What are my chances of getting a good one?

1 AMD Opteron processor Model 146 2GHz 1MB 939pins, Retail OS146BNBOX $208.06 $208.06
Sub Total $208.06
Tax $0.00
Shipping Method: UPS 2nd Day Air Track Shipping
Shipping $14.41
Total $222.47
Order Status
Date Status
2005-10-20 Online order received
2005-10-21 Inventory Processing
2005-10-21 In Warehouse
2005-10-21 Shipped

[foofreaknfighte]

Ok, I think I am giving up on my OCZ PC4000 Gold. I guess I will drop it back into my p4 system where it seemed to do great. What memory has had the most success on these opterons? I am thinking maybe crucial ballistix? I want a couple gigs.

[NWEng]

Don't feel bad, I'm dumping my 3700EB in favor of some Geil One's.

[=Pseudo=]

My opty under testing:

http://img465.imageshack.us/img465/1846/opteron1469days8ep.jpg

I've been afk (out of the country) for about 10 days but the system was running folding with that config. This will be the base for further testing ;) .

Since I had some trouble to set the mems @290 in the few hours I've played with it I've used the divider... hope to put it back 1:1 after tweaking.

At the moment, I've just reduced vcore to 1.39v and I'll leave until tomorrow. Then more results will come...hopefully. :rolleyes:

cheers

[dogsx2]

At last I got a mb that works. Put back in the 144 to run spi at 3.0MHz.

http://img460.imageshack.us/img460/1541/1443032m1uq.th.jpg (http://img460.imageshack.us/my.php?image=1443032m1uq.jpg)

http://img488.imageshack.us/img488/4683/144300dg.th.jpg (http://img488.imageshack.us/my.php?image=144300dg.jpg)

Sure wish that 9/10 worked.

[gundamit]

@dogsx2

Hopefully that new Ultra-D you picked up from the Egg is a good one. 334HTT right out of the box doesn't seem to be a problem for the DFIs. I took that for granted until I started playing with the EVGA and Asrock mobos recently. Seems like the DFI is the only good option for 9x multis. If you find time, please drop the multi to 8 and show us your highest HTT. :D

BTW - On the 32M runs please open the box up a little more before running it so we can see the final time.

[laydback]

I love my GeiL One's, runs @ 300mhz with no problem with only 2.8vdimm.

[dogsx2]

@dogsx2

Hopefully that new Ultra-D you picked up from the Egg is a good one. 334HTT right out of the box doesn't seem to be a problem for the DFIs. I took that for granted until I started playing with the EVGA and Asrock mobos recently. Seems like the DFI is the only good option for 9x multis. If you find time, please drop the multi to 8 and show us your highest HTT. :D

BTW - On the 32M runs please open the box up a little more before running it so we can see the final time.

Sorry, I didn't notice. I put on an 8x and upped the Vcore alittle. I took it to 380HTT and quit, I'm sure it will do more. I ran pi 1m, didn't feel like running 32m right now. This board is better then my rma'ed mb. I'll test it out and see how high I can go with the 144@8x running pi 32m.

http://img459.imageshack.us/img459/6444/144380htt4xt.th.jpg (http://img459.imageshack.us/my.php?image=144380htt4xt.jpg)

[dinos22]

Seems like the DFI is the only good option for 9x multis. I think you missed Abit there....they can certainly do high HTT no probs out of the box

[dogsx2]

Picked up some cheap($107.50 shipped) ocz 4000vx and put them in. Alittle better then the 4800's. They don't take as much volts as I thought they would.
I love this 144 more then the other two.

http://img467.imageshack.us/img467/7628/14430vx4tk.th.jpg (http://img467.imageshack.us/my.php?image=14430vx4tk.jpg)

[dinos22]

I love this 144 more then the other two.how many have you got heheh

[dogsx2]

how many have you got heheh

Not as many as gun, I only have a 144,146 and 148.

Does that time with the vx's seem right, I thought they would tear up the 4800's.

[xforce]

Received my Opty 148 939 from Compumusic.
Guess what. Its a CABNE stepping.

OSA148DAA5BN
CABNE 0528GPMW

:D

But no mobo. Waiting for the DFI RDX200 to retail again.

:slobber:

[dinos22]

Not as many as gun, I only have a 144,146 and 148.

Does that time with the vx's seem right, I thought they would tear up the 4800's.
heheh damn i want a CABNE......you dude have a whole bunch too :(

[eva2000]

heheh damn i want a CABNE......you dude have a whole bunch too :(
yeah same here :)

[dogsx2]

heheh damn i want a CABNE......you dude have a whole bunch too :(

Be thankful you don't, they're a great burden to bear.

[MsB]

Im too lazy to go all the way back thru. Has anyone tried any of the duallys? 165, 170, or 175?

[gundamit]

Be thankful you don't, they're a great burden to bear. :rofl: I only have 3 same models as you. My fourth - a 146 - I only have a shipping notification for it. Nice HTT on your DFI.

[gundamit]

Im too lazy to go all the way back thru. Has anyone tried any of the duallys? 165, 170, or 175? Use the search thread feature.

http://www.xtremesystems.org/forums/showthread.php?p=1087269&highlight=175#post1087269

[dogsx2]

Received my Opty 148 939 from Compumusic.
Guess what. Its a CABNE stepping.

OSA148DAA5BN
CABNE 0528GPMW

:D

But no mobo. Waiting for the DFI RDX200 to retail again.

:slobber:

After messing with a stinking asrock mb, you couldn't pay me to take on a rdx200. I think (unless they really get to clocking them) I will just stick with Ultra-d until the 940's come out.

[dinos22]

Be thankful you don't, they're a great burden to bear.
let me un-burden you a little......i'll buy one of them no probs heheh...even a couple of you want :)

[shimmishim]

7 hours later... large fft prime still goin' strong

opty 148 CABYE 0528GPMW

2.88 ghz with 1.55 volts

no IHS (helped me out a lot)

http://www.johnshim.com/forums/xtremesystems/2880primelargefft.jpg

[Rasped]

Long time lurker, first time poster.
Just a quick question. How many with CABNE has removed their IHS?
And do the CABYEs with the IHS off clock as good as the CABNE with IHS?
Could it be that the biggest change between the CABYE and the CABNE is the contact between the IHS and the CPU?

Now how is that for an entry to the board? KISS
Keep It Stupid... Stupid.

[Eljefe62]

I finally got my 146... 0530 CABNE... it is only doing 2700right now, crap MSI neo2 won't let me crank up my ballistix to 1t and about 260 @ 3338 timings. Will do further testing and post results when I get a chance...

[gbomb944]

I've been wondering the same thing about the IHS making the difference on some of these steppings. Maybe the tim was a different sucky batch or the machine that applies it or the ihs was not running well for whatever reason. I can't remember if anyone did a naked cabge but maybe it would help.

Also I think it would be great if everyone who has a chip would put in the week stepping and where they got it into their sig. A guy posts "look at my cabxe from XXXXX" and then 20 posts later who knows what chip it is? Even worse they don't tell where it came from. I've been here for the whole thread but I can't remember everything and I'm not going to scroll back through 50 pages with 1200/1600 jpg's all over the place. (which is another issue, Hint: shrink the pics and lower the quality.)

Cooling would be nice too as everyone has to keep asking over and over "what step", "what cooling", "where'd you get it", etc. At least put the step up in screenies.

[T_M]

well said gbomb, on all counts

[Ugly n Grey]

Whatever happened to the concept of thumbnail? I have turned off pictures in user control panel, I just click the link when I want to see them. I'm not looking at a zillion piccys when the data can be summed up in about five works words...... 32Meg stable, 3.0Ghz blah blah blah...

Edit: Not OT, moderation work LOL :)

[dogsx2]

Whatever happened to the concept of thumbnail? I have turned off pictures in user control panel, I just click the link when I want to see them. I'm not looking at a zillion piccys when the data can be summed up in about five works words...... 32Meg stable, 3.0Ghz blah blah blah...

Edit: Not OT, moderation work LOL :)

I agreed, I posted on this when I had venices and sd's. In the oc'ing threads you wolud see one guys pics for the whole page. I have dsl and the screen would still be moving and shaking loading when I though it should be done.

This should be something the mods and owner should discuss.

[fullup3]

OK, so I've had my vandi special 146 cabne for about 10 days now, and I've been rather dissapointed because it wouldn't get to 3000 stable like almost all others. After seeing some of the others results with removing the IHS, I thought I'd give it a try. Right after I popped the top, I ran super pi 32m at 1.55v @ 3006mhz....Hell Yes!! :banana: :banana: My temps dropped considerably, and this is in a room @ 72degrees f, and with the zalman 7700.
But right after the first run of 32m, I rebooted to try to clock higher, and my neo 2 died on me... ouchee :slobber: :slobber:
Now I'm at default vcore 2800mhz on the abit av8 (board won't go much higher), and will be waiting on the new board from rma before I can test again.

Ah, so is the life of the overclocker....victories, and defeats one after another!!!

[el rolio]

OK, so I've had my vandi special 146 cabne for about 10 days now, and I've been rather dissapointed because it wouldn't get to 3000 stable like almost all others. After seeing some of the others results with removing the IHS, I thought I'd give it a try. Right after I popped the top, I ran super pi 32m at 1.55v @ 3006mhz....Hell Yes!! :banana: :banana: My temps dropped considerably, and this is in a room @ 72degrees f, and with the zalman 7700.
But right after the first run of 32m, I rebooted to try to clock higher, and my neo 2 died on me... ouchee :slobber: :slobber:
Now I'm at default vcore 2800mhz on the abit av8 (board won't go much higher), and will be waiting on the new board from rma before I can test again.

Ah, so is the life of the overclocker....victories, and defeats one after another!!!

ok so wow. us neo2 owners are really having a hard time eh? but this makes me raise na eyebrow. popping the top eh? you + me + Eljefe62 all have a vandi special cabne 146 wk 30. all have the neo2. all have been pumping volts and getting high frikken temps. like i can get to 32m stability with less volts than prime stability (which im testing right now, pics later) butt oif you saw my screenshots a few pages back (which was only day and half ago) i got it to 2.9 but not without a fight and not without dropping my ram speed damn cllose to stock.

and sitting here typing this on the lappy, its showwin me 58° on the cpu, under a storm block and water, 1.58 - 1.6v since this neo2 loooooves to fluctuate so wildy.

i mean its beeen runnin since i got in from clubbin so its been a while. i do not however want to run above 55° for my load temps at all. cuz i refuse to make the system loud. so does this mean i bacck down from 290x10? go slower? i could do 2.8ghz pretty much damn near stock and i know im pumping extra volts into this thing now to compensate for voltage swings but wow.

so mainly, i love my ihs, i love how they look ive always said i leave the poppin of the top to the phaser's etc and i really feel like i would be defacinng a peicce of art. but if it REALLLY nets such big temp drops for us neo2 146 cabne wk30 vandi special owners, (say that 5 times fast) then i will prolly have to do it.

let me know mane, and all other neo2 owners. ps: im curently on 1.b tccd mod bios, will ggo back to 1.c when its final. what you guys on?

[dogsx2]

I have a neo2 and a dfi and an asrock sata2. The neo must just read the temps hot. On the other mb's the temps a lot cooler. I can't believe that somehow the msi makes the cpu run hotter. Here's a post from a few days ago of mine before your post.

http://www.xtremesystems.org/forums/showthread.php?p=1087152#post1087152

[Eljefe62]

@ 1.45v mine is running 45º idle, according to BIOS (who knows if this is right!); I have an xp90 with decent (ie, not a tornado...) fan. I am using the 1.b ballistix bios on my neo2. Have not had a chance to really play with overclock yet...

[ben805]

This is one of the three 148 CABNE 0528 GPMW that I have, room temperature is 75'F, using the TT Big Typhoon heatsink with Silverstone FM121 110cfm fan rated at 39dB in a closed case PC, the only thing I can hear is my PSU fan. After 16hr of Prime the cpu temperature is still ROCK SOLID at 39'C :D :D 3.0Ghz @1.47v (300 x10) and 2GB of Ballistix running at 300 @3-3-3-8 1T using 704-2BTA bios, this chip passed 3Dmarks, OCCT, SPI32M, and now Prime. Whenever I have a chance I'll test the other two CABNE. :toast:


http://www.xtremesystems.org/forums/attachment.php?attachmentid=38917

[gundamit]

Whatever happened to the concept of thumbnail? I have turned off pictures in user control panel, I just click the link when I want to see them. I'm not looking at a zillion piccys when the data can be summed up in about five works words...... 32Meg stable, 3.0Ghz blah blah blah...

Edit: Not OT, moderation work LOL :) I totally agree. What worse is when some guy makes multiple post showing esentially the same thing ... "32Meg stable, 3.4Ghz blah blah blah... tightened timings ...blah blah blah ... knocked off 28 seconds ... " and you know they're planning on tryin their BH-5 or TCCDs next so they post yet again the same pic with a few changes. I know the type. Something should be done! :soap:

http://img463.imageshack.us/img463/765/309x11patriots3bw.png

... well at leastiI use png files which are pretty small relative to jpegs. Less than 90kb for the above shot. :D

[dogsx2]

[QUOTE=ben805]This is one of the three 148 CABNE 0528 GPMW that I have, room temperature is 75'F, using the TT Big Typhoon heatsink with Silverstone FM121 110cfm fan rated at 39dB in a closed case PC, the only thing I can hear is my PSU fan. After 16hr of Prime the cpu temperature is still ROCK SOLID at 39'C :D :D 3.0Ghz @1.47v (300 x10) and 2GB of Ballistix running at 300 @3-3-3-8 1T using 704-2BTA bios, this chip passed 3Dmarks, OCCT, SPI32M, and now Prime. Whenever I have a chance I'll test the other two CABNE. :toast:


Is this more fun then a x2, I sure think it is. :D We used to dream about clocks like this. Maybe you could do a comparison between x2 and opty like you did with sd and venice. :)

[Rufus7]

Nice clocks Ben 805 with Air.Congrats. My temps are higher with an SI120 and an Papst4412 F/2GL 63cfm

[dogsx2]

Way to go. :woot:

What did you do to get over the hump?

[gundamit]

I'm just playing around with some of the timings and Tref. Take little 1M runs to see if I picking up any time. When I manage to knock off a few tenths of a seconds off the 1M time I figure it'll add up on the 32M. I'm no Pi guru but its fun making that number go down. I want to try the BH-5 again. I should be able to get a respectable time that won't have XS members lining up to :slapass: me.

[fullup3]

Yea, el rolio, I think you should lose the IHS. I didn't want to do it either, but It made a huge difference on the one and only run I've made without it. Allowed me to the the 3giga that is so sought after.
When I get my new board back in, I'll be able to see how much it really helped.

[eR1k]

I'm just playing around with some of the timings and Tref. Take little 1M runs to see if I picking up any time. When I manage to knock off a few tenths of a seconds off the 1M time I figure it'll add up on the 32M. I'm no Pi guru but its fun making that number go down. I want to try the BH-5 again. I should be able to get a respectable time that won't have XS members lining up to :slapass: me.
My question isn't very topic related, but did you turn the heater on the backplate and in the promhead off to reach lower temps with your opteron? Just wondering...

[gundamit]

My question isn't very topic related, but did you turn the heater on the backplate and in the promhead off to reach lower temps with your opteron? Just wondering... Uh ... no. Do you have a link to a post that proved this was beneficial?

[eR1k]

Uh ... no. Do you have a link to a post that proved this was beneficial?
http://xtremesystems.org/forums/showthread.php?t=24574&highlight=heater+mach

IMHO Marci knows a lot about this stuff, so i think with some extra armaflex it might be a good idea.

[njkid32]

Hey guys well I just got my 146 opty and here are some first run results. Not much but more to come.

http://img468.imageshack.us/img468/126/opty31ghz5in.th.png (http://img468.imageshack.us/my.php?image=opty31ghz5in.png)

[Jester FPS]

Dang that cpu is on fiya! Is that on cascade or what?

[el rolio]

I totally agree. What worse is when some guy makes multiple post showing esentially the same thing ... "32Meg stable, 3.4Ghz blah blah blah... tightened timings ...blah blah blah ... knocked off 28 seconds ... " and you know they're planning on tryin their BH-5 or TCCDs next so they post yet again the same pic with a few changes. I know the type. Something should be done! :soap:

... well at leastiI use png files which are pretty small relative to jpegs. Less than 90kb for the above shot. :D

you sir a pro screenshotter. for this i shall always use thumbnails tho im not sure peeps click on them, so then i shall install a program hopefully ot ass big as photoshop that will allow me to crop screenshots and post sub 100k pics. yay.

oh and you at 3.4ghz is oh so ridiculous

[el rolio]

Hey guys well I just got my 146 opty and here are some first run results. Not much but more to come.

http://img468.imageshack.us/img468/126/opty31ghz5in.th.png (http://img468.imageshack.us/my.php?image=opty31ghz5in.png)

wow. i envy your vcore. and iu wanted to know, is there any benefit ot using the simple prime95 thing? i mean i like that teh program you have there priming shows speed and running time. that would be nice to knnow, as it stands now my machine is priming and ireally ahve no idea how many hours its been going. and i'd like to get back to working on the machine.

oh and if this program is pretty good to use annd combines the other stability testers... id like to know what its named.

[el rolio]

I have a neo2 and a dfi and an asrock sata2. The neo must just read the temps hot. On the other mb's the temps a lot cooler. I can't believe that somehow the msi makes the cpu run hotter. Here's a post from a few days ago of mine before your post.

http://www.xtremesystems.org/forums/showthread.php?p=1087152#post1087152

yea man, i remember that post now (thread soooo long gah! forgetting things) now that i have mine i can see that it really is crazy what the msi reports. so i guess i wont worry much about the temps its telling me im getting. i mean the air coming from the rad fans is kinda warm under fully load but really not that bad.

ok so that would confirm my suspicions... neo2 definitely reports super high. for that matter it has issues reporting nb fan speeds too. i actually only trust the ambient from the 6800.

the next thing is this top popping. you really making me think about it. but then again a guy over at my [H] worklog suggested adding some capacitors to the board to stabilize the vcore some more. imm happy for systool, it actually shows when the frikken vcore drops... so if any of your neo2 owners know whats up with that lemme know.

ozzimark and i were thinking the mem controller was flaky which is why i had to be running the 150 divider but like dog said, its hte neo2 and the problem it provides to get superpi stable cuz of lack of ram. at least the new bioses SE makes help the situation out.

if im then gonna be keepin my ram below 215 i really think im gonna put hte bh-5 back in.

another one of my main issues is selecting voltage for hte core. its like trial an error to get a decent voltage and it almost seems that certain combinations are more stable than others.. right now im 1.45 + 8.3% im pretty sure which is currently proving to be stable. even tho i could complete superpi with less; once i got my memory voltage sorted that is.

[foofreaknfighte]

Ok. I am about to pull the trigger on 2 gigs of g1's. Speak now or forever hold your peace.

[ben805]

Here's my 2nd 148 CABNE 0528, yet another awesome 3Ghz chip. Performance and underload temperature is identical to the 1st one I'd tested :D :D the only difference is this one has slightly lower MaxTcase than the other one.

http://www.xtremesystems.org/forums/attachment.php?attachmentid=38923

[fareastgq]

I think I'll die if my 175 doesn't have your stepping Ben,.....

[75sausage]

I think that they posted that they were instock to just hype things up a little and get orders in could be for real though but dont give your hopes up
148 shipped friday from monarch scheduled to arrive monday 10/24

[mongoled]

Here's my 2nd 148 CABNE 0528, yet another awesome 3Ghz chip. Performance and underload temperature is identical to the 1st one I'd tested :D :D the only difference is this one has slightly lower MaxTcase than the other one.

Damn you 3Ghz posters with less volts than me :slapass: :D

You definately going to push me over the edge to get another mthbrd! Cant get it out of my mind tht better vCore regulation will allow me to run lower vCore for 3Ghz.

Until i get another mobo I wont know for sure. Just saw a post over at dfi-street on the new RDX200 CF-DR and the guy is running 3Ghz with 1.4v over 3hrs prime95 stable on WC

:slobber:

His chip is a Opteron 150 0534SPMW dont know if it is CABNE/CABYE or CABGE most likely not CABGE, heheeee

[[XC] 4X4N]

Just getting a chance to play with this. 148 CABYE 0528 GPMW received from ewiz on wednesday. 2.8@stock volts is stable. Here is a 32m pi shot. Also ran prime large fft for about an hour with no errors. 33-34 idle, 42-43 load. Upped volts to 1.325x113% Can do a 1m pass, but fail 32m. Still have my timings pretty tight, might try to loosen them up a little.Temps now, 36-37 idle, 45-46 load. Would like to up the volts more but temps are climbing fast. My venice never goes over 43 with almost 1.6v. Cooling with big typhoon. Don't know if I will make 3.0, but still seems like a damn nice chip.

[shimmishim]

Just getting a chance to play with this. 148 CABYE 0528 GPMW received from ewiz on wednesday. 2.8@stock volts is stable. Here is a 32m pi shot. Also ran prime large fft for about an hour with no errors. 33-34 idle, 42-43 load. Upped volts to 1.325x113% Can do a 1m pass, but fail 32m. Still have my timings pretty tight, might try to loosen them up a little.Temps now, 36-37 idle, 45-46 load. Would like to up the volts more but temps are climbing fast. My venice never goes over 43 with almost 1.6v. Cooling with big typhoon. Don't know if I will make 3.0, but still seems like a damn nice chip.

sounds just like mine.

i'm at 2.9 with 1.55 volts but prime large fft's errored out at 12 hours :(

[Eljefe62]

2800 now, just gotta use the divider... stability only tested using dawn of war for an hour, but I play games, so that's stable for me.

[ben805]

Nice clocks Ben 805 with Air.Congrats. My temps are higher with an SI120 and an Papst4412 F/2GL 63cfm

thanks man....I loves these CABNE, I thought about getting WC for the Opty but the Big Typhoon + FM121 fan perform so well even in a closed case that I'm just going to stick with air :D :D






Is this more fun then a x2, I sure think it is. :D We used to dream about clocks like this. Maybe you could do a comparison between x2 and opty like you did with sd and venice. :)

hehe....these opty are sure fun to play with. Though I kinda missed my X2 as I noticed day to day usage none of the single core can touch the X2, ever since nvdia release the 81.84 drivers to take advantage of the dual core I think it definitely close the gap between the two in gaming, running at the same clock speed the X2 with 81.84 driver still rules the Aquamark over this opty (105K vs 99K), 3dmark 05 is very close but the Opty really shine on both 01 and 03. But I know one thing for certain....my X2 will not do 3.0Ghz on air :D :D I don't think I should do a detail comparo between the two as I don't think it's fair :D :D




I think I'll die if my 175 doesn't have your stepping Ben,.....

I hope you get a good one man....where did you get the 175 and for how much if you don't mind me asking.

[njkid32]

Here is a better update. Man I love this chip! CABNE 0530APMW it will go up to 3.3ghz at stock volts. But I am starting here. One thing I did notice is that it does not like the 180 or the 166 divider if I use a divider I have to use the 150 or 133. Thats the only flaw I can see so far.
http://valid.x86-secret.com/show_oc?id=45130
http://img461.imageshack.us/img461/3918/opty31ghz21gb.th.png (http://img461.imageshack.us/my.php?image=opty31ghz21gb.png)

[fareastgq]

I just ordered it from monarch, 599+ ship, they are more expensive than 4400's, but I'm banking on better silicon overall, I'm sure it will do at least 2.8 24/7 anyway. I don't think they actually had it in stock though since I ordered on the 19th and they say it won't ship until monday, which is kinda ok, because my biostar (tide me over board) will be here on monday and I can just throw my 4400 in it for right now. That'll at least give me a good idea of how well these biostar boards are since everything else will be the same. :)

On a side note, I'm going to try this low volt burn in method on the operton ( I have to express that I totally do not believe in cpu burn in, but hey...whatever, I still gotta try it to see if it'll yield me higher clocks.) Mainly because this will be the last chip upgrade I get until the next socket comes out. I suspect the overall clocks will be the same once I hit a voltage wall, it may clock higher at a lower voltage, (which is not the max clock of the chip) but then, that's useless to me... oh well, time will tell.

[[XC] 4X4N]

Thought I had 2.9 stable but prime just failed after about 1 1/2 hours, so I just went for 3.0 for 1m pi. Temps seem to be staying about the same, even with voltage at 1.4x113% Here's the shot. No more time for today. Tomorrow I'll play with my memory settings more, I think that is what's holding me back.

[dinos22]

Thought I had 2.9 stable but prime just failed after about 1 1/2 hours, so I just went for 3.0 for 1m pi. Temps seem to be staying about the same, even with voltage at 1.4x113% Here's the shot. No more time for today. Tomorrow I'll play with my memory settings more, I think that is what's holding me back.
hi mate

i think you should play with you MAL and Read Preamble timings....should give you better stability

[computerpro3]

3.1ghz 1m superpi stable.

IHS on, more left in it. This is on an xp-120 with a low speed panaflo L1A

http://images.dr3vil.com/upload2/3.1ghz.JPG

ignore the crappy time, my memory was running @ 200mhz to isolate cpu.

[shimmishim]

More tweaking.

Got superpi 32M stable now at 3000 mhz :)

had to use the 166 divider. i think i might have a weak mem controller (again).

link to 32M ss (http://www.johnshim.com/forums/xtremesystems/3000spi32m.jpg)

[eva2000]

More tweaking.

Got superpi 32M stable now at 3000 mhz :)

had to use the 166 divider. i think i might have a weak mem controller (again).

link to 32M ss (http://www.johnshim.com/forums/xtremesystems/3000spi32m.jpg)
what ram is that as the rime is tad slow

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/166/325-266-2225-8-18-2222_1.55-1.3-1.6-3.59_3120_dsW2dds1_16clk_9F6_16x7x/superpi-32m_8clk_tn.jpg

[shimmishim]

what ram is that as the rime is tad slow

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/166/325-266-2225-8-18-2222_1.55-1.3-1.6-3.59_3120_dsW2dds1_16clk_9F6_16x7x/superpi-32m_8clk_tn.jpg

it's 2x1 gig crucial ballistix.... not great for benching :)

i upped it to the 180 divider (ram now at 272 HTT) and i got 25 minutes 16 seconds.

[njkid32]

Here are some more results. It seems that this cpu responds well to volts. Does anyone have thoughts or ideas on some other timings I could try... Thanks

http://valid.x86-secret.com/show_oc?id=45186
http://img478.imageshack.us/img478/6228/opty34ghz0ek.th.png (http://img478.imageshack.us/my.php?image=opty34ghz0ek.png)

[ben805]

Here are some more results. It seems that this cpu responds well to volts. Does anyone have thoughts or ideas on some other timings I could try... Thanks

http://valid.x86-secret.com/show_oc?id=45186
http://img478.imageshack.us/img478/6228/opty34ghz0ek.th.png (http://img478.imageshack.us/my.php?image=opty34ghz0ek.png)



jeeewiz....you guys are running 3.4 under phase and your result made my 3.0 on air looks like child play, my PCICE single stage is sitting in the corner giving me a smirk :stick:

[Rufus7]

@Ben805 i have bought a WC to get higher than 3Gig on good Temps. Next week the
WC System will bei completed. And than i will go for 3,2Gig Primestable or more.
And the CABNE is the best CPU i´ve ever had. Not much Vcore but a plenty of clocks.

[dogsx2]

jeeewiz....you guys are running 3.4 under phase and your result made my 3.0 on air looks like child play, my PCICE single stage is sitting in the corner giving me a smirk :stick:

It's really funny how these optys really changed how we now look at oc's.

BO(before opty) and AO(after opty).

BO if you had a cpu that would hit 2800-2900 it was above average.
AO if your cpu doesn't hit 3000 it's below average.
BO on single phase 3000-3200(non-FX) was pretty good.
AO on single phase 3400(non-FX) is starting to be comon.

This cpu really raised the bar.

[el rolio]

screenshot of my 2.9, hey at least i found the way to only campture the part of the screen i want. still aint installed PS to resize so i can directly post into the thread the way i want to.... bu it dont matter anyhoo i spose.
http://img454.imageshack.us/img454/1514/29stablehot7nb.th.png (http://img454.imageshack.us/my.php?image=29stablehot7nb.png)

[laydback]

Here are some more results. It seems that this cpu responds well to volts. Does anyone have thoughts or ideas on some other timings I could try... Thanks

http://valid.x86-secret.com/show_oc?id=45186
http://img478.imageshack.us/img478/6228/opty34ghz0ek.th.png (http://img478.imageshack.us/my.php?image=opty34ghz0ek.png)

Have you tried messing with DQS?

[gundamit]

I thought I should be able to get Prime stable at between 3.2 and 3.3ghz. I ran off 3.3ghz "large FFT" and did over two hours on it. But its just too boring. I had to stop it. Here it is for what its worth.

http://img422.imageshack.us/img422/5540/300x11largeend3ty.th.png (http://img422.imageshack.us/my.php?image=300x11largeend3ty.png)

[Eljefe62]

I am in the 3GHz club on air! Not stable (yet), and running on a divider... All this on my pos Neo2.

[el rolio]

yea i can get to windows at 315x10..... wont even bother trying to stabilize that heh.... so im stayin at 2.9 it seems. and you know what? thats fine with me, my winnie took me to 295x9 and this is now a nice speed bump, and fun.... and hot.

[Eljefe62]

I'm perfectly OK with 2.9, but if I can get to 3 w/out much effort, why not? I am having an issue with my Neo2 only allowing me 2t on the mem. I thought it was the mem controller on my 3200+, but the Opty does it too. I am convinced it is the crap Neo2 and that I have slightly scorched something using the ddr booster (not currently using it). Could I just have bad luck with processor mem controllers? I don't think a brand spanking new Opty would have such a hard time with 1t...

[gundamit]

Got all three of my benching sets of memory to 3.4ghz with the 148. Last one to get a chance was the BH-5.

http://img382.imageshack.us/img382/4640/309x11bh52nd5ex.png

[eR1k]

Beautiful results :slobber:

[ben805]

It's really funny how these optys really changed how we now look at oc's.

BO(before opty) and AO(after opty).

BO if you had a cpu that would hit 2800-2900 it was above average.
AO if your cpu doesn't hit 3000 it's below average.
BO on single phase 3000-3200(non-FX) was pretty good.
AO on single phase 3400(non-FX) is starting to be comon.

This cpu really raised the bar.


yea I know....seems like only the CABNE and some CABYE can hit the magic number, though I'm wondering how well these opty's memory controller going to hold up with all the abuse we're throwing at them, I sure hope they built like tank and last for a little while :D :D

[ben805]

I thought I should be able to get Prime stable at between 3.2 and 3.3ghz. I ran off 3.3ghz "large FFT" and did over two hours on it. But its just too boring. I had to stop it. Here it is for what its worth.

http://img422.imageshack.us/img422/5540/300x11largeend3ty.th.png (http://img422.imageshack.us/my.php?image=300x11largeend3ty.png)


2hr of prime at 3.3Ghz is impressived!! thanks for running it and if you can do higher...like 3.35~3.4, please post the result whenever you have a chance as well :D :D

[gbomb944]

Looks like i started something with the image thing. In the interest of lighting a candle I started a thread on image resizing and free image progs.

http://www.xtremesystems.org/forums/showthread.php?p=1099083#post1099083

The short version of it is download the image viewer from here http://www.faststone.org/. It doesn't seem to have spyware or vir's but use at your own risk. It's pretty cool and you can save as lots of different file types and all that. Saving as a 256 color gif or png seems to give good results and small size or just save as jpeg and lower the quality slider under save as-advanced .

I actually like the pics in the forum better than thumbs or links but just not so huge and at too high color so they take all day to dl.

[eva2000]

my PBs for Opteron 144

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/150/336-252-2225-7-16-2212_1.67-1.3-1.6-3.44_3120_dsW2dds1_0clk_9F65_16x7x/superpi-1m_tn.jpg

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/150/335-251-2225-7-16-2212_1.67-1.3-1.6-3.44_3120_dsW2dds1_0clk_9F65_16x7x/superpi-8m_tn.jpg

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/150/335-251-2225-7-16-2212_1.67-1.3-1.6-3.44_3120_dsW2dds1_0clk_9F65_16x7x/superpi-32m_tn.jpg

[el rolio]

Looks like i started something with the image thing. In the interest of lighting a candle I started a thread on image resizing and free image progs.

http://www.xtremesystems.org/forums/showthread.php?p=1099083#post1099083

The short version of it is download the image viewer from here http://www.faststone.org/. It doesn't seem to have spyware or vir's but use at your own risk. It's pretty cool and you can save as lots of different file types and all that. Saving as a 256 color gif or png seems to give good results and small size or just save as jpeg and lower the quality slider under save as-advanced .

I actually like the pics in the forum better than thumbs or links but just not so huge and at too high color so they take all day to dl.


thank you kind sir, exactly what i was lookin for!

[mongoled]

@Ben805 i have bought a WC to get higher than 3Gig on good Temps. Next week the
WC System will bei completed. And than i will go for 3,2Gig Primestable or more.
And the CABNE is the best CPU i´ve ever had. Not much Vcore but a plenty of clocks.
Well i wouldnt hold my breath, prime95 stable with just watercooling for 3.2ghz just aint going to happen. Now if you chill the water than that a different thing.

So are you going to chill your water? id be amazed if your chip could do 3.2Ghz prime95 stable with normal water.

[Fallengod]

I dont see why. Peoples chips do 3.1 on air... Whats another 100mhz on water.





Well i wouldnt hold my breath, prime95 stable with just watercooling for 3.2ghz just aint going to happen. Now if you chill the water than that a different thing.

So are you going to chill your water? id be amazed if your chip could do 3.2Ghz prime95 stable with normal water.

[njkid32]

Here is a prime run at 3.3ghz. Its only an hour and could have kept going but didnt want to wait anymore. Jeez I even hate waiting for a 32m run. LOL Anyway ram needs tightening up and fine tuning but here is it...

http://img312.imageshack.us/img312/3599/32ot1.th.jpg (http://img312.imageshack.us/my.php?image=32ot1.jpg)

[dogsx2]

I dont see why. Peoples chips do 3.1 on air... Whats another 100mhz on water.

Alot, 100mhz after 3.1 is a bunch if your on regular water. I agree with mongoled.

You may be able to ss or 1-8m but I wouldn't bet the farm on 32m at 3.2 on reg water.

[Rufus7]

Well i wouldnt hold my breath, prime95 stable with just watercooling for 3.2ghz just aint going to happen. Now if you chill the water than that a different thing.

So are you going to chill your water? id be amazed if your chip could do 3.2Ghz prime95 stable with normal water.

No i wont chill my water for the first. I want to see how high the chip is going under normal watertemps. Later i will try to chill the water a little bit, but not too much.

[mbm]

Have been offered this stepping
Opteron 146 cabye 0536 gpmw.
Is this much better than my CABGE?

[Rufus7]

mbm look here if you want to see how high the Steppings goes.

http://www.forumdeluxx.de/forum/showthread.php?t=162502

[mongoled]

I dont see why. Peoples chips do 3.1 on air... Whats another 100mhz on water.
Like dogsx2 said,

the peeps doing 3.1ghz on air are doing just screen shots, I aint seen no 3.1Ghz screen shots of prime95 on air, have you?? These chips once they go past 3Ghz, need alot more cooling then below 3ghz. Id be very impressed if a saw a 3.1ghz prime95 stable chip on normal water, nevermind 3.2Ghz, then I would be :slobber: and cursing the person who had it!@! LOL

:D

Good luck with tht chip Rufus, from your air results it sure shows alot of promise

[Rufus7]

Heres one Screenshot on Air with my APMW at 3050Mhz on Air. And one who failed at 3100Mhz on Air.

http://img368.imageshack.us/img368/9272/3050mhz1408vcprime4h4vr.th.jpg (http://img368.imageshack.us/my.php?image=3050mhz1408vcprime4h4vr.jpg)


http://img368.imageshack.us/img368/4314/3100mhz1408vcprime4h0sz.th.jpg (http://img368.imageshack.us/my.php?image=3100mhz1408vcprime4h0sz.jpg)

[computerpro3]

Like dogsx2 said,

the peeps doing 3.1ghz on air are doing just screen shots, I aint seen no 3.1Ghz screen shots of prime95 on air, have you?? These chips once they go past 3Ghz, need alot more cooling then below 3ghz. Id be very impressed if a saw a 3.1ghz prime95 stable chip on normal water, nevermind 3.2Ghz, then I would be :slobber: and cursing the person who had it!@! LOL

:D

Good luck with tht chip Rufus, from your air results it sure shows alot of promise

I can do a 1m superpi on air easy 3.1ghz. You must have missed my post, its more than just a screenie. IF I put another fan onto my heatsink to replace my 59CFM 20DB panaflo I can do 32m most likely.

IF I pop the heatspreader I have no doubts at all that I will be 3.1-3.2ghz prime stable on air. Gotta see whether its worth doing though, especiually when I have phase change coming. Dont want to wreck what seems to be the 2nd best opteron on air out there.

[mongoled]

I can do a 1m superpi on air easy 3.1ghz. You must have missed my post, its more than just a screenie. IF I put another fan onto my heatsink to replace my 59CFM 20DB panaflo I can do 32m most likely.

IF I pop the heatspreader I have no doubts at all that I will be 3.1-3.2ghz prime stable on air. Gotta see whether its worth doing though, especiually when I have phase change coming. Dont want to wreck what seems to be the 2nd best opteron on air out there.
Please do this, rather than talking abt it!!!! SuperPi 1M is easy peasy. Also suggesting tht it is 'likely' u can do 32M is again not good enuff, we dont do 'likely' here, SS and verification is where its at.

You seem very confident tht you will do 3.1-3.2Ghz prime stable on air, 100mhz difference is alot when talking abt prime95 stability! Please make my comments look silly and jealous by showing me a prime95 screen shot at 3.1Ghz on air......

i can just see you living in the north pole in your igloo at - 30C posting a prime95 screenshot at 3.3ghz, LOL

:rofl:

[ixtapalapaquetl]

I aint seen no 3.1Ghz screen shots of prime95 on air, have you?? Does this count as prime stable on air?http://img473.imageshack.us/img473/6451/30663d01evwrprimestable4uq.png (http://imageshack.us)

No IHS, but I later realized when working on a 144 CABYE that the Windows was corrupt. Also on a nF3; my nF4 Ultra-D comes this week at which time I'll give 3.15 a serious go.

[Vapor]

With the Opterons it seems it's 1M MHz minus 100-120MHz that's P95/OCCT stable.

Going from decent air to good watercooling only gains 50-80MHz. So if you're 1M stable at 3.1GHz right now, add 50MHz for the slightly better cooling and removing the IHS and then subract 110MHz for the P95/OCCT stable and you get 3.04GHz most likely.

No way you'll get 3.1 stable even on good water if it can 'only' do 1M @ 3.1GHz right now.

And (insert crazy long name here), yes that counts as Prime stable but not 3.1GHz ;)

And what kind of aircooling do you have? 30C idle temps are about 8C lower than I get with water :stick:

[ixtapalapaquetl]

And what kind of aircooling do you have? 30C idle temps are about 8C lower than I get with water :stick:Magic air cooling? In seriousness, I use a XP-90. Ambient is around 19C, and my case is open.

[HermS]

With the Opterons it seems it's 1M MHz minus 100-120MHz that's P95/OCCT stable.

I'd agree with that, it seems to be the way my chip reacts too.

[mongoled]

With the Opterons it seems it's 1M MHz minus 100-120MHz that's P95/OCCT stable.

Going from decent air to good watercooling only gains 50-80MHz. So if you're 1M stable at 3.1GHz right now, add 50MHz for the slightly better cooling and removing the IHS and then subract 110MHz for the P95/OCCT stable and you get 3.04GHz most likely.

No way you'll get 3.1 stable even on good water if it can 'only' do 1M @ 3.1GHz right now.

And (insert crazy long name here), yes that counts as Prime stable but not 3.1GHz ;)

And what kind of aircooling do you have? 30C idle temps are about 8C lower than I get with water :stick:
Thts a good rough analysis on how these chips will clock,

as for the ambient temperatures, they are very low, looks like we will be going back to the discussion if air-con units strapped into case count as 'air-cooling'

Anyone got a butchers freezer near them, take your system in their, with your 'air-cooling' and get a prime95 stable scrren shot at 3.7Ghz

:D :D

tht would be air cooling right, LOL

hehehehehee

[dogsx2]

Does this count as prime stable on air
.

Nope, 3.1 is 3.1. On my 148 the last 30MHz comes hard. This isn't hand grenades ads or horseshoes. :D

[mongoled]

Magic air cooling? In seriousness, I use a XP-90. Ambient is around 19C, and my case is open.
:slobber: :slobber:

You got XP-90 and 30C idle temps with 1.6v :eek: , wht are your load temps, you got a freeking different CPU to the rest of us!!!

-EDIT-

Offtopic question, just noticed tht ixta... is on a nForce3 mthbrd, whts the voltage regulation like on those boards, better than the NF4's??

[dogsx2]

:slobber: :slobber:

You got XP-90 and 30C idle temps with 1.6v :eek: , wht are your load temps, you got a freeking different CPU to the rest of us!!!

I don't know if you had a 9c ambient you could do 30c idle. :stick:

[mongoled]

I don't know if you had a 9c ambient you could do 30c idle. :stick:
Yes possibly, with 9C but he has 19C ambient. Im on water cooling with 1.57v (multimeter) IHS removed and im idling at 30-33C right now, ambient temps id say are 19C.

[ixtapalapaquetl]

whts the voltage regulation like on those boards, better than the NF4's??That is the million dollar question. I have always assumed that it is worse. I am getting a nF4 Ultra-D later this week, so I will have some interesting comparisons soon. Much more important than +/- 50MHz, however, will be my newfound ability to run my FF's at 1T!!! Now THAT'S going to make me happy!

@dogsx2: yeah, that last 34MHz is quite a hill to climb! We'll see...

[ben805]

148 running at 3.06Ghz @1.60v 30'C on air??? wow.....what kind of "air" you got there? can you get me some too? :D :D not only the cpu, but your chipset running at 1.6v and only 32'C and LDT voltage at almost 1.9v but pwmic only at 33'C!! interesting....still very nice clock and nice temperature though.

[Rufus7]

I don't know if you had a 9c ambient you could do 30c idle. :stick:

No for 30°C Idle its enough around 15°C Ambient with an XP90 and 1,376vcore.
But 1,6Vcore its very hard with the IHS still on.

[Vapor]

But 1,6Vcore its very hard with the IHS still on.That's exactly our point....

[dogsx2]

I think this might be the max on this CABYE 148 on air. The 146 and this 148 are sure close on max. I might be able to squee alittle more out of them. If only I had ixtapalapaquetl cooling, I know I could. :D

If you see anything in the 148 tweaker that will make it better, I'll sure try it.

http://img405.imageshack.us/img405/4568/1483070vx1cc.th.jpg (http://img405.imageshack.us/my.php?image=1483070vx1cc.jpg)


Here's the 146:
http://img405.imageshack.us/img405/1521/14630705ot.th.jpg (http://img405.imageshack.us/my.php?image=14630705ot.jpg)

Gun, here's the top HTT on this new mb:
http://img405.imageshack.us/img405/744/1484029ri.th.jpg (http://img405.imageshack.us/my.php?image=1484029ri.jpg)
I forgot to reset the tweaker, sorry.

[F|apDro|`]

:slobber: :slobber:

You got XP-90 and 30C idle temps with 1.6v :eek: , wht are your load temps, you got a freeking different CPU to the rest of us!!!

-EDIT-

Offtopic question, just noticed tht ixta... is on a nForce3 mthbrd, whts the voltage regulation like on those boards, better than the NF4's??

I have TT BT and I get 28C idle with 1.6V .. loaded 47C max...

With 1.55V idle = 28C ... Load = 44C max

With default V's = 26C idle and 39-40 load...

This is on MSI k8n neo2 plat blabla :p..

[dogsx2]

I have TT BT and I get 28C idle with 1.6V .. loaded 47C max...

With 1.55V idle = 28C ... Load = 44C max

With default V's = 26C idle and 39-40 load...

This is on MSI k8n neo2 plat blabla :p..

I have both, it must be kinda cool this time of year Somewhere in Hollanda. :) Do you live by ixtapalapaquetl?

[HermS]

If you see anything in the 148 tweaker that will make it better, I'll sure try it.

http://img405.imageshack.us/img405/4568/1483070vx1cc.th.jpg (http://img405.imageshack.us/my.php?image=1483070vx1cc.jpg)

Assuming thats UTT then trfc 14 (12 if BH-5), preamble 6-6.5ns, MAL 7/8

[Vapor]

And trrd to 0 and trtw to 1.....good luck with those though ;)

Might want to also experiment with tref.

[ozzimark]

as for the ambient temperatures, they are very low, looks like we will be going back to the discussion if air-con units strapped into case count as 'air-cooling'
chilled air. can't argue with that :D

[mbm]

mbm look here if you want to see how high the Steppings goes.

http://www.forumdeluxx.de/forum/showthread.php?t=162502

There isnt the Batch numbers!
Cant se if its CABNE CAYNE or CABGE

[t-max]

Who is saing that the cabye do not rock :D
Water cooled IHS OFF

3200mhz Spi 1M 25,813 sek

3150mhz Spi 32M 23m12,047sek

3180mhz 3D05/03
http://service.futuremark.com/compare?3dm05=1354938

[dinos22]

Who is saing that the cabye do not rock :D
Water cooled IHS OFF

3200mhz Spi 1M 25,813 sek

3150mhz Spi 32M 23m12,047sek

3180mhz 3D05/03
http://service.futuremark.com/compare?3dm05=1354938
what sort of water cooling do you have....Congrats....that is certainly a very very nice chip

[dogsx2]

Who is saing that the cabye do not rock :D
Water cooled IHS OFF

3200mhz Spi 1M 25,813 sek

3150mhz Spi 32M 23m12,047sek

3180mhz 3D05/03
http://service.futuremark.com/compare?3dm05=1354938

Nice chip. I think the 148's are pretty good with any stepping. I have seen any bad 148's yet.The 144's get ALL the junk that doesn't cut it for the higher speeds.

[ixtapalapaquetl]

Nope, 3.1 is 3.1. On my 148 the last 30MHz comes hard. This isn't hand grenades ads or horseshoes. :DCan anybody loan me a few MHz?

http://img489.imageshack.us/img489/6545/3098prime1pt.png (http://imageshack.us)

Man, I was all set to just sit here contentedly until my new board showed up, but y'all had to be droppin gauntlets and sh*t! LOL. Dunno what happened. Took this 148 out two days ago to play with a 144, now my 148 is going higher and at lest voltage! Yes, I live in the ghetto so no, my apartment doesn't have any heating (and probably won't for another month - f'in cheapa** slumlords - but I digress), but this is still on air with ambient 18C. Speedfan shows lower temps than MBM. Also included a pic of Vcore - do nF4's rock more stably? Sorry about the myopic image. Don't have time to resize... will give 3.12GHz a shot next.

[Richdog]

Does anyone have any info on the new Opteron 150's with the 2.4ghz clock speed? http://www.komplett.co.uk/k/ki.asp?sku=313933&cks=NWP

They're going to be available for a decent price apparently, and with all the decent 144's and 146's all but gone over here, i'm interested to know how they'd clock. :)

[F|apDro|`]

I have both, it must be kinda cool this time of year Somewhere in Hollanda. :) Do you live by ixtapalapaquetl?

Could be colder here ... like 15C outside but on my room 20-21C ...

But yeah my temp sensors suck on the MSI :stick:

[t-max]

what sort of water cooling do you have....Congrats....that is certainly a very very nice chip

Swiftech STORM cpu head 2 x gtx in the loop and a trible radi.

[gundamit]

3150mhz Spi 32M 23m12,047sek Very nice. Amazing amount of volts through a CPU cooled with water. IHS removal a little more tempting. :thumbsup:

[computersmsa]

Hi,

I have just received 60 Opteron 144 CABNE 0540 APMW !
First look, not very good for CABNE : 2.85 GHz @ 1.6V stable with my WC.
However, CABNE are special about RAM setting, I will test later !
Now, I make dispatch and logistic.

[furyfax]

Damn, www.komplett.no had 2 OPTERONS 150's and those were the only OPTERONS s939 available here in norway. I hope these OPTERONS get available soon.
I have a question, is it possible taht the OPT 170 has 2 cores which are same stepping like the FX-57? In other words it's a dualcore FX-57, that would be fun.

PS.
My english sucks..

[eva2000]

Hi,

I have just received 60 Opteron 144 CABNE 0540 APMW !
First look, not very good for CABNE : 2.85 GHz @ 1.6V stable with my WC.
However, CABNE are special about RAM setting, I will test later !
Now, I make dispatch and logistic.
looks like aggressive speed binning has started to occur

[Pt1t]

Hi,

I have just received 60 Opteron 144 CABNE 0540 APMW !
First look, not very good for CABNE : 2.85 GHz @ 1.6V stable with my WC.
However, CABNE are special about RAM setting, I will test later !
Now, I make dispatch and logistic.


dispached !

http://users.skynet.be/pt1t/144/CABNE_0540.jpg :toast:

[gbomb944]

OUch. Looks like the later weeks of 146 suck. If you look on the db the top ones are 0530's and the clocks get lower as they go up in weeks. It's a small sample but weeks/vs clocks there seems to be a direct relation.

http://www.webspace-giant.com/thegame84/Opteron146.htm

Maybe those 0540's will do better.

[gbomb944]

I wonder if amd can test these before they put the pins on? Maybe the good ones get turned in to 940 pins for the most part as they are more serious use. 2.8 is not bad but nothing to write home about either.

[gundamit]

OUch. Looks like the later weeks of 146 suck. If you look on the db the top ones are 0530's and the clocks get lower as they go up in weeks. It's a small sample but weeks/vs clocks there seems to be a direct relation.

http://www.webspace-giant.com/thegame84/Opteron146.htm

Maybe those 0540's will do better.That always seems to be the general pattern with new releases. Initial weeks look good then it drops off some. Then everyone waits around until another "good" week comes along. I'm just wondering if dollar for dollar the average Operton will continue to represent better value than its Venice/San Diego counterparts.

[t-max]

Very nice. Amazing amount of volts through a CPU cooled with water. IHS removal a little more tempting. :thumbsup:

Year it can take a ton of v.core with the IHS off and still stay cool, it was like burning under the IHS reaching 60C load at only 1,6 v.core :mad:

tok off the IHS and now i can run even 1.75 v.core still keep it under 55 C :woot:

[el rolio]

Year it can take a ton of v.core with the IHS off and still stay cool, it was like burning under the IHS reaching 60C load at only 1,6 v.core :mad:

tok off the IHS and now i can run even 1.75 v.core still keep it under 55 C :woot:

SO TEMPTING!

[Razor_cut]

Year it can take a ton of v.core with the IHS off and still stay cool, it was like burning under the IHS reaching 60C load at only 1,6 v.core :mad:

tok off the IHS and now i can run even 1.75 v.core still keep it under 55 C :woot:

And so dangerous.. What if you f**k up? there goes 220$ :(

But shurely I will try it also. Hmm

[sauria]

What's the stat on the "kill rate" from doing this?

[Rufus7]

Black Ice Extrem II is on the way to me. This week i will get some results with the new WC System.

[Vapor]

I'm diggin the first 4 numbers of the serial numbers of the new 0540APMW's ;)

Can't wait for results from them.....and their higher binned counterparts if they exist.

[sauria]

Anyone got ahold of a Opty 180 yet?

[Vapor]

Nope....175s and down have been all that's available thus far.

[perry_78]

Allright, ordered a 0540APMW to be a guinea pig - now to get some ram :D

[gbomb944]

well the monarch 146 is 0536gpmw. Too bad I don't have a board.

[computersmsa]

Wich bios and setting do you council me for a CABNE (0540 APMW) and 2*512 Mb of UTT BH-5 (CMSAM) ?

Thx :toast:

[perry_78]

I'd say 510-2, which gave me the best results running both Winchester, Venice and SD. Used both TCCD and old BH5, though I have yet to play with an opteron.

*wink, low batch number computersmsa :D

[gbomb944]

dispached !

http://users.skynet.be/pt1t/144/CABNE_0540.jpg :toast:


Holy $h*T your chip is leet! Look at the first four numbers. 1337

[Amdfreaker]

Holy $h*T your chip is leet! Look at the first four numbers. 1337

What does that mean?

[menlatin]

^^ Leet... elite ... like 1337 H4x0r.

[gbomb944]

Probably nothing as far as oc. leet or 1337 is h4XXor for elite or cool.

http://www.google.com/search?client=opera&rls=en&q=1337&sourceid=opera&ie=utf-8&oe=utf-8

I honstly think leetspeak is pretty silly but to each his own or is that pwn?

[Pt1t]

CABNE 0540 APMW ...1207.

I m still testing it , 32M passed @ 3ghz , 1.64v

1M passed 3031mhz , 1.67v under watercooling

but i think , this cpu can take more vcore ...

http://users.skynet.be/pt1t/144/3031_1,67v.PNG

[Repoman]

Damn I think ewiz messed up my order.. it says RMA under order status? Why would it say that.. I haven't even had the chip yet.

Anyway do you guys know where there are any good steppings for sale.. I think I'll cancel this one from ewiz because they are seriously pissing me off, they have no more stock and I bet they gave my damn chip away..

[F|apDro|`]

those new CABNE's just look like the CABYE if I see those result :stick: ( at least when I look at my 148 CABYE )

[perry_78]

CABNE 0540 APMW ...1207.

I m still testing it , 32M passed @ 3ghz , 1.64v

1M passed 3031mhz , 1.67v under watercooling

but i think , this cpu can take more vcore ...


Great, I hope mine performs similairly well! Did you get yours from computersmsa?

[Pt1t]

Great, I hope mine performs similairly well! Did you get yours from computersmsa?

yep

[75sausage]

Fresh of the FedEx truck from Monarch Computer...
Should I be going :banana: :banana: :banana: 's

[[XC] 4X4N]

Looking back through the thread it seems most people are running MAL of 8-9, and preamble of 6.5-7.5 at 3.0ghz. Do you guys have that set in bios, or do you change it after booting into windows with a64 tweaker? Anything above 7.5 MAL blue screens on me before getting to windows. I have tried changing it with a64 tweaker, but it freezes on me. I have 3.0ghz sort of stable. 1m, 4m 8m pi pass, but fail 32m about half way through. Thinking that this may be why. Thanks.

[nfm]

Setup:

Opteron 146 CABYE 0536 GPMW Retail, from Monarch
Oh forgot cooling, was done on cheapo Tt Venus12 really well lapped
DFI nf4 SLI-DR, 510-2ModFix BIOS
OCZ PC3200 Rev2 TCC5 2x512MB RAM
OCZ PowerStream 520W
for rest look at sig

Windows XP Pro x64 (64-bit)

http://www.xtremesystems.org/forums/attachment.php?attachmentid=39046&stc=1

THIS IS WITHOUT IHS, I FOUND OUT THAT THERE WAS HORRIBLE CONTACT BETWEEN IHS AND CPU CORE, max spi1m along with spi8m before was 2.95GHz with same settings, AND THIS CHIP RUNS HOT LIKE S*IT, was 62C loaded before, don't know how much now after taking off IHS :D I'll keep you updated


EDIT: Hmmm, 3004Mhz is my max spim1 stable with above settings, will try more vcore :D Here's Snadra shot:

http://www.xtremesystems.org/forums/attachment.php?attachmentid=39047&stc=1


EDIT2: Bad news, 3012 is the max on this cpu with 1.63 volts, won't try any more volts

[ben805]

Looking back through the thread it seems most people are running MAL of 8-9, and preamble of 6.5-7.5 at 3.0ghz. Do you guys have that set in bios, or do you change it after booting into windows with a64 tweaker? Anything above 7.5 MAL blue screens on me before getting to windows. I have tried changing it with a64 tweaker, but it freezes on me. I have 3.0ghz sort of stable. 1m, 4m 8m pi pass, but fail 32m about half way through. Thinking that this may be why. Thanks.


combination of MAL 9.0 and PRE of 7.0 usually work pretty well..these opty are tricky! do it in BIOS and see if you can even load up the built in memtest, if you can't....then don't bother to load up windows.

[NiSMo]

im havin trouble getting SP2004 and OCCT stable at 2900mhz / 1.54v

everything else is stable, 3dmark05 (4 loops), stresscpu (3days continuously), superPI (1m - 32m), CS:S (bout 4hrs of play).

im thinking its my ram timings etc...

http://img20.imageshack.us/img20/5212/helpwitmemtimings7wx.jpg (http://imageshack.us)

anythin other info u need just ask :), also rest of system specs r in sig

[nfm]

Ok latest update :toast: :

http://www.xtremesystems.org/forums/attachment.php?attachmentid=39049&stc=1

Still unoptimized, 23min xx sec is achievable, I'll work on that tomorrow, now time for some BF2 ;)

[fullup3]

Mine doesn't like sp2004 AT ALL. I can game and run OCCT at 3000 1.5v.
But my chip takes 1.425v to even prime at 2800.
Not sure what's going on, but as long as everything else runs stable, I'm happy.

[[XC] 4X4N]

Ok, since I am having trouble getting anything over 2.8 100% stable, I decided to try for a max clock. 11x278 1m pi pass. Broke into 27 seconds :woot: Opteron 148 CABYE 0528 GPMW

[el rolio]

im havin trouble getting SP2004 and OCCT stable at 2900mhz / 1.54v

everything else is stable, 3dmark05 (4 loops), stresscpu (3days continuously), superPI (1m - 32m), CS:S (bout 4hrs of play).

im thinking its my ram timings etc...

anythin other info u need just ask :), also rest of system specs r in sig

well, randomly, i did my 290x10 stable with at least 1.55v as opposed to your 1.54 *shrug

[Pt1t]

Opteron 144 CABNE 0540 AMPW with HIS under WC

http://valid.x86-secret.com/cache/45631.png

http://users.skynet.be/pt1t/144/CPUMARK_405.PNG

[Chicco85]

Hi,

Now I have my new opteron...

Here you are the sigle:

CABGE 0536VPMW

How do you think about it?

This afternoon I will test it....

Bye! :D

[dinos22]

Opteron 144 CABNE 0540 AMPW with HIS under WC

http://valid.x86-secret.com/cache/45631.png

http://users.skynet.be/pt1t/144/CPUMARK_405.PNG
not bad....what's it stable at :toast:

[Pt1t]

not bad....what's it stable at :toast:
i m still testing, for now , 4h prime95 , 3ghz 1.64v

[dinos22]

i m still testing, for now , 4h prime95 , 3ghz 1.64v
damn that's just tops...you belgians are crazy mofo OCers with your super high vcore with ghetto WC hehehe :toast: :toast: :toast:

[Pt1t]

damn that's just tops...you belgians are crazy mofo OCers with your super high vcore with ghetto WC hehehe :toast: :toast: :toast:

The 0540 needs more vcore than 0530 :slapass: , i only give what it want :D

[Pirated]

Hey! duds... is there anyone using socket 939 opterons here?

[alpha0ne]

Hey! duds... is there anyone using socket 939 opterons here?

939 Opterons ??, why would we use those :rolleyes: (jk)

[eR1k]

Hey! duds... is there anyone using socket 939 opterons here?
Are you for real? :slap:

[Pirated]

@alphaone:
@er1k:

I am just asking who where using socket 939 opterons not the way you answer me, buset!

[gbomb944]

Just a note about mal and preamble that everyone keeps asking about is that these are highly dependant on your ram. You need to find the settings that work on YOUR ram and the mal and preamble settings you can use will change with clock as well. Just because they are opterons doesn't mean that you can use the same mem settings on diff types of mem. If it worked that way I'd get some value ram and run it at 260 2225.

These are ram timings not cpu timings.

[LexDiamonds]

Pirated- This whole thread (all 70 glorious pages of it) is about 939 opterons. If it wasnt so late, I would have taken a laugh at your expense too, but others already beat me to it.... :slash:

[gbomb944]

I'm insanely jealous of your 0528 cabne sausage. That thing should be awesome.

Although I don't have a board for my 0536 I'm guessing I'll get 2800 stable if I'm lucky
I don't even want to go 1.6 unless I can help it. Popping the lid doesn't really bother me but after I lapped my sweet 2600 and it died after 3mo's anything that keeps me from rma'ing is not something I want to do.

When your broke, and pay arseloads of child support it's not as easy to buy toys and blow them up. Take a lesson kids....wrap your rascal and don't believe it when they say they're on the pill. :nono:

[gundamit]

I'm insanely jealous of your 0528 cabne sausage. That thing should be awesome. Hmm ... sausage envy. :confused:


When your broke, and pay arseloads of child support it's not as easy to buy toys and blow them up. Take a lesson kids....wrap your rascal and don't believe it when they say they're on the pill. :nono: Double bag it. Paper and plastic.

[Zeus]

@alphaone:
@er1k:

I am just asking who where using socket 939 opterons not the way you answer me, buset!

How about reading this thread starting at page 1? :slapass:

[gbomb944]

Well the jury is still out but I have feeling his e-sausage is going to be bigger than mine.

[Pirated]

Lexdiamonds: Thank dud's if you're quite hesitant to divulge the thread about socket 939 opterons. Anyway, i am a bit slowly in viewing the thread. So, for that sorry if i disturb your serene moments, hehehe...

It is clear that i've said anyone using 939 opterons because most images of the thread showed mostly socket 940, i am right? So, why are maggots keep on bullying me, huh!

Can you understand? I here to know more about 939 opterons not to talk to you, ok...

[gundamit]

Lexdiamonds: Thank dud's if you're quite hesitant to divulge the thread about socket 939 opterons. Anyway, i am a bit slowly in viewing the thread. So, for that sorry if i disturb your serene moments, hehehe...

It is clear that i've said anyone using 939 opterons because most images of the thread showed mostly socket 940, i am right? So, why are maggots keep on bullying me, huh!

Can you understand? I here to know more about 939 opterons not to talk to you, ok... This is what I love about XS. Despite our language barriers we're reaching out to each other and ... :slapass: Its the universal language apparently. :p:

BTW the 940 you see is just CPU-Z reading it wrong. These are all 939s here.

[Zeus]

That's a bug in CPU-Z, it doesn't recognize S939 Opterons, will be fixed in the next version of CPU-Z i hope.

[eva2000]

Using my custom meanwell psu to over volt my MCP650 has helped a tad for oc'ing

http://www.fileshosts.com/watercooling/custompsu/html/photos/custompsu_005.jpghttp://www.fileshosts.com/watercooling/custompsu/html/photos/custompsu_027.jpg
http://www.fileshosts.com/watercooling/custompsu/html/photos/custompsu_003.jpghttp://www.fileshosts.com/watercooling/custompsu/html/photos/custompsu_004.jpg

Top right pic you can see the white plastic dial to adjust the voltage output. I marked the max voltage output on the black switch/relay box myself to tell them apart :D

This is with MCP650 at 13.23v - seems to get a bit more stable and finally completed 32M at 3024mhz! Timings were looser than my sub 24min time at 3015mhz though heh.

http://www.fileshosts.com/DFI/NF4_SLI_D/results/Opteron144/CABYE_0536_GPMW_2/Corsair/XMS3500C2/2x512/2_1/623_2BTA/LDT3x/150/336-252-2225-7-17-2213_1.70-1.3-1.6-3.48_3120_dsW2dds1_8clk_9F65_16x7x/superpi-32m_tn.jpg

Kayl did an excellent job as last night i let the psu run my MCP650 @13.23v overnight and no probs. Noticed post-load temps drop to idle levels alot quicker now.

i.e. with 1.55v vcore

before at 12.4-12.6v on MCP650
before stressing cpu idle = 38C
cpu load = 49-52C
post stressing cpu idle = would drop to 40-41C for 1-3 seconds and then drop to 39C then 38C

now at 13.23v on MCP650
before stressing cpu idle = 37-38C
cpu load = 46-51C
post stressing cpu idle = would drop immediately to 38C

I guess the custom psu would have better improvements overvolting MCP600 or MC350 pumps but seems MCP650 is liking it too :)

Going to play with the voltage output and see what's best for my MCP650.

[Pirated]

@gudamit
@zeus

Thanks for the great info's... That's a nice person i know not like others here, right? Even if where not known each other personally be courteous, ok!

I love friendly person... :)

[eva2000]

my local Aussie retailer's latest opteron 146 batch are CABYE 0540FPBW should have mine by end of this week :)

more fun :D

[Jesus]

OK now I have a dilemma.

CABGE 0536 VPMW- 144
or
CABYE 0530 GPMW--146
both on e-bay
the 146 ran 2,6@1,45V Prime stable on a AV8 3rd eye

The 144 never ran.

Gennerally speaking which one is better 144 or 146? Or maybe 148?

advice, suggestions, cheques, :D all welcome

[eR1k]

I'd go for the 146 because of the 10x multi and the cabye stepping.

[75sausage]

Hey! duds... is there anyone using socket 939 opterons here?
Late but nontheless...

You either:
A: Are retarted.
B: Have a sick sense of humor.

Thanks for a good laugh this morning! :clap:

[75sausage]

Hmm ... sausage envy. :confused:
.
I get that alot :rolleyes:

[Davos]

what sort of chips are being rolled out atm? are there any good clockers still coming, or are we onto the crap ones now :)

[Chicco85]

Hi,

Now I have my new opteron...

Here you are the sigle:

CABGE 0536VPMW

How do you think about it?

This afternoon I will test it....

Bye! :D


I made a first rapid test... 2530 Mhz v.core default...

Now I'll try ti increase the v-core.

[gbomb944]

Alright pirate I suppose you can be let slide since the title of the thread doesn't specify 939, maybe it should be changed but anyway everything here is 939. You should still read some of a thread before posting I'm sure it's in there somewhere. Only about 20 guys have asked the same question.

also it's "dudes" not "duds". duds is not really a good thing to call people in english. It's a bomb that didn't go off or somebody/thing that sucks. a lamer.

[Pirated]

I agree all... you're great. Anyway, whatever it is... come's from mistake! woot... sorry all, newbies here... if god forgives ~ i'm not talented as you are like 75suasage... i want to eat this guy, hehehe...

OT:)

Back on the topic....

[furyfax]

Here in Norway no opterons are available at the moment, I am more interested in the DC OPTY's, are they available in the U.S ? Haven't found any OC results yet.

[Rufus7]

Here in Norway no opterons are available at the moment, I am more interested in the DC OPTY's, are they available in the U.S ? Haven't found any OC results yet.

You can get the DC Opterons also in Germany. www.alternate.de or other big vendors. Try it with www.geizhals.at

[Rufus7]

[QUOTE=Rufus7]You can get the DC Opterons also in Germany. http://www.alternate.de/html/shop/productListing4C.html?cat1=003&cat2=223&cat3=000&treeName=HARDWARE&Level1=CPU&Level2=Desktop&Level3=Sockel+939& or other big vendors. Try it with http://www.geizhals.at/?cat=cpuamd939

[75sausage]

I agree all... you're great. Anyway, whatever it is... come's from mistake! woot... sorry all, newbies here... if god forgives ~ i'm not talented as you are like 75suasage... i want to eat this guy, hehehe...

OT:)

Back on the topic....
Thx for keeping a sense of humor... ;)
and by the way, I'm with the n00b crowd.

[Pt1t]

Here in Norway no opterons are available at the moment, I am more interested in the DC OPTY's, are they available in the U.S ? Haven't found any OC results yet.


here also , they are available :

http://www.bel-hardware.be/forum/viewtopic.php?id=675

if you order quickly , it will be CABNE 0540 APMW.

[furyfax]

But I'm interested in the dual core opterons! The OPTY 170 is the one i want. I just spoke with a guy i know in a computer shop and they thought they would have the OPTY 170 within 2 weeks. I have to save up som cash and then I'll get this CPU! :D
Is the CABNE 0540 really good OC'er?

[Rufus7]

The CABNE0530APMW certain but the 0540APMW??? Test it and we will know it.

[furyfax]

Haven't seen any result of the CABNE 0540APMW just yet. Or have i missed it? :confused:

[Pt1t]

The CABNE0530APMW certain but the 0540APMW??? Test it and we will know it.

i tested it, the previous page.

[Rufus7]

Sorry Pt1t.
But 1 Exemplar is not representativ only shows the Way of the Stepping.
And the 0540 Needs a lot of Vcore for 3 Gig.Too much for my Taste.
Stress the Hardware too much.

[Pt1t]

Sorry Pt1t.
But 1 Exemplar is not representativ only shows the Way of the Stepping.
And the 0540 Needs a lot of Vcore for 3 Gig.Too much for my Taste.
Stress the Hardware too much.


with 1.6v hardware isnt too much stressed , with the cabge 144 0536 vpaw i ran 32M @ 1.84v cpuz

[Rufus7]

Good Luck for the other one. And allways cool water.

[furyfax]

Pt1t post your result of the other CPU when it's ready!

[Pt1t]

Good Luck for the other one. And allways cool water.

For 3ghz 1.64v , i have 27° idle and 43-44° after 4h of prime.

[Pt1t]

Pt1t post your result of the other CPU when it's ready!


I have to finish to work !

[perry_78]

I have to finish to work !

No you don't :p:

Good luck with it though!

[furyfax]

If the DC OPTY's are available elsewhere why aren't there any results posted yet! I have made an " The Unofficial Dual Core Opteron Overclocking" Thread for results.

[Rufus7]

Here is one from Germany where i´m daily looking and typing.

http://www.forumdeluxx.de/forum/showthread.php?t=162502

[gbomb944]

Originally Posted by chz
I'm using the 618 bios without problems. Anyways getting tired of my 57-ish load temps i decided to whip out the razor and cut off the ihs. Cleaned it and the core, added some arctic ceramique instead of the stock crap and put the IHS back on. Since i'm too much of a chicken to risk my opty with my cnsp 9500 which weighs a ton i wanted to see if even something as simple as this made a difference.
My load temps are now 48-50.. thats almost a 10C drop just by replacing the paste.. the ihs is still there protecting the core, insane. Don't know what they did during the manufacturing of these optys but placing those intergrated heatsinks sure was a shoddy job.

Not bad, I may have to do this. Just have to stick it back on nice. does anybody know what the black goop they stick it on with is?

[freestylercs]

I tried 2900MHz with lowest Vcore.

144 0530 APMW under water for long time at prime.

http://mitglied.lycos.de/freestylercs/hpbimg/2900MHz@1,32V%20prime.JPG

free

[el rolio]

Originally Posted by chz
I'm using the 618 bios without problems. Anyways getting tired of my 57-ish load temps i decided to whip out the razor and cut off the ihs. Cleaned it and the core, added some arctic ceramique instead of the stock crap and put the IHS back on. Since i'm too much of a chicken to risk my opty with my cnsp 9500 which weighs a ton i wanted to see if even something as simple as this made a difference.
My load temps are now 48-50.. thats almost a 10C drop just by replacing the paste.. the ihs is still there protecting the core, insane. Don't know what they did during the manufacturing of these optys but placing those intergrated heatsinks sure was a shoddy job.

Not bad, I may have to do this. Just have to stick it back on nice. does anybody know what the black goop they stick it on with is?

ooo now THAT im down to try, but i hope it can be secured back on properly ya know...

[Pt1t]

http://users.skynet.be/pt1t/144/7002.PNG

i tried 3dmark with high vcore , 1.62v needed , but i m testing the gto²

[Nano2k]

http://users.skynet.be/pt1t/144/7002.PNG

i tried 3dmark with high vcore , 1.62v needed , but i m testing the gto²

J'attends mon proc de Computersmsa :-)

Gotta love that "Can't score? Maybe it's your hardware!" add in the 3dmark window lol!

[WesM63]

Well I cancled my order for my 144 thru my vendor and ordered a 146 from ewiz, it will prolly be crap but oh well. :rolleyes: I should have some results this weekend.

[computersmsa]

I have found time for me, my CABNE 0540 APMW is in socket !
I will test the max stable @ 1.4V this evening, the rest tomorrow.

[perry_78]

I have found time for me, my CABNE 0540 APMW is in socket !
I will test the max stable @ 1.4V this evening, the rest tomorrow.

Excellent. Preliminary results will be available from me on Friday - too much work until then, still have about 4 essays in total to write for this week :(

[jetjaguar]

hmm is it still worth ordering an oem 146 from monarch ?

[perry_78]

nice avatar

perhaps, in Europe the belgian mega order is a better deal it seems.