View Full Version : First DI run
Apocalipsis
04-18-2005, 12:15 PM
Hello guys, thx to chilly1 I just finished my first DI run last weekend, not bad at all.
Installing thermal sensor on cpu pipe.
http://www.infonegocio.com/frikiland/dryice/sensor.jpg
Installing the cpu pipe.
http://www.infonegocio.com/frikiland/dryice/pipe1.jpg
http://www.infonegocio.com/frikiland/dryice/pipe2.jpg
http://www.infonegocio.com/frikiland/dryice/pipe3.jpg
http://www.infonegocio.com/frikiland/dryice/pipe4.jpg
http://www.infonegocio.com/frikiland/dryice/back.jpg
Testing...
http://www.infonegocio.com/frikiland/dryice/vapor.jpg
Idle temp.
http://www.infonegocio.com/frikiland/dryice/idletemp.jpg
Load temp.
http://www.infonegocio.com/frikiland/dryice/loadtemp.jpg
The cards.
http://www.infonegocio.com/frikiland/dryice/gpuinsulation.jpg
http://www.infonegocio.com/frikiland/dryice/gpuinsulation2.jpg
All installed.
http://www.infonegocio.com/frikiland/dryice/rig.jpg
A funny shot.
http://www.infonegocio.com/frikiland/dryice/inside.jpg
Comments are welcome.
Regards,
Apocalipsis.
kristos
04-18-2005, 12:24 PM
those 3 containers look wicked :banana:
Waus-mod
04-18-2005, 12:27 PM
Indeed, verry nice container!
What insulation did you used for the motherboard? or didnt you used any
Apocalipsis
04-18-2005, 12:31 PM
Unfortunately, the day I finished the mounting of the 3 containers I was running out of dryice, that was 3 days after I bought 10kg.
The only thing I did was a fast 3DMark03 run, getting 26799 points.
Cards were running 550/1300, FX only 3240mhz, not too much, perhaps the cpu is not very good, next thursday I will receive 10kg more of DI and the test will continue.
Man, you dont know how hard was to install that middle container there :woot:
HARDCORECLOCKER
04-18-2005, 12:33 PM
:D Yeah - nice triple tube array, but show us a 3D Mark.......... :p:
:toast:
Apocalipsis
04-18-2005, 12:37 PM
Indeed, verry nice container!
What insulation did you used for the motherboard? or didnt you used any
Only back insulation (the pic is not very clear but there is a thick neoprene sheet under the backplate), about 6 hours running the cpu container and no problems, chilly1 insulation kit works very good.
Waus-mod
04-18-2005, 12:38 PM
i have almost the same insulation kit and also a round container. but still using some neophrene around the socket and plastic spray..
Apocalipsis
04-18-2005, 12:40 PM
:D Yeah - nice triple tube array, but show us a 3D Mark.......... :p:
:toast:
You can see me here http://www.xtremesystems.org/forums/showthread.php?t=51594
4th best score on 03 :D
More shots this weekend, I promise, hope for 3rd 03 and 5th 05 on hall of fame.
Apocalipsis
04-18-2005, 12:43 PM
i have almost the same insulation kit and also a round container. but still using some neophrene around the socket and plastic spray..
I remounted the cpu pipe a few times after some hours running, didn't see any sign of condensation, but well, as you say, more insulation never hurts, thx for your tip.
Apocalipsis
04-18-2005, 12:46 PM
bios reports about -20ยบ, do you know if that is accurate? or better not to trust it?
Bloody_Sorcerer
04-18-2005, 01:19 PM
better not to trust it. On-die thermal sensors aren't worth a crap.
Very nice DI rig there, lovin the SLI DI.
twilius_basic
04-18-2005, 01:21 PM
Dude, that is awesome! :surf:
Very nice setup job there, I'm sure you'll do well once you get some more DI.
That is so cool seeing 3 tubes all mounted up :D Props m8, and thanks for the good pics....
Apocalipsis
04-18-2005, 01:29 PM
Thx guys !! ;)
Your praises are the best bounty :toast:
BigPanda
04-18-2005, 03:32 PM
better not to trust it. On-die thermal sensors aren't worth a crap.
Very nice DI rig there, lovin the SLI DI.
better not to trust it. On-die thermal sensors aren't worth a crap.
Very nice DI rig there, lovin the SLI DI.
I not sure but i think it should be higher like -40 or somthing
Thx guys !!
Your praises are the best bounty :toast:
No Problem Good Job on your first run :up:
Apocalipsis
04-18-2005, 09:35 PM
With an LS unit, the ondie sensor report about -10, so at least I know is colder than that.
Perhaps will try to install a sensor touching the IHS.
Waus-mod
04-19-2005, 10:21 AM
The container isolation is that quite longer than the container itself ?(under the mounting plate?) so it insulates the motherboard aswell (how many mm?)?
Apocalipsis
04-19-2005, 10:33 AM
Do you mean neoprene thickness between mobo and backplate? that's about 5-6mm.
vapb400
04-19-2005, 01:55 PM
very nice! i cant wait to get my tubes finished.
BigPanda
04-19-2005, 04:31 PM
very nice! i cant wait to get my tubes finished.
I just need to figure out somthing for the mounts and order some insulation
Looks awesome, is the cpu container blocking the memory at all?
reject
04-19-2005, 10:15 PM
wow that looks like VERY hard work 3 tubes!
am i correct in assuming those arte chilly1 tubes, or at least chilly hold downs?
Apocalipsis
04-20-2005, 10:22 PM
Looks awesome, is the cpu container blocking the memory at all?
No it isn't.
Apocalipsis
04-20-2005, 10:24 PM
wow that looks like VERY hard work 3 tubes!
am i correct in assuming those arte chilly1 tubes, or at least chilly hold downs?
Yes, all chilly1 tubes :up: and yes a VERY hard work, specialy to mount the middle container, that was a pain.