View Full Version : 1GB DDR600 8-3-3-2.5 1T on Neo2 24/7 - possible???
bachus_anonym
01-06-2005, 02:32 PM
Hey folks,
Well, i'm in the market for another new memory sticks - this time to put it in my Neo2 for 24/7 usage ONLY.... I need it to be "prime-3D-game-stable" @ DDR590-600ish with 8-3-3-2.5 1T timmings.
Does Gskill PC4400 LE cut the mustard for this task ??? I see some people with those clocks but I cannot recall anyone showing full-stability at this speed?
What do you guys think? Do you have any ideas, please?
[XC] moddolicous
01-06-2005, 02:41 PM
That should work, but I dont think those timings are worth it. Try like DDR 500 at lower timings. You could also try BH-5 with alot of volts, but that might not be what you are looking for.
That should work, but I dont think those timings are worth it. Try like DDR 500 at lower timings. You could also try BH-5 with alot of volts, but that might not be what you are looking for.
hm. Anything to testify this statement?
DDR500 2-2-2-5 (BH-5) vs DDR600 2.5-3-3-8 1T (G.Skill TCCD)
skate2snow
01-06-2005, 03:25 PM
TCCD will give better performance on A64 S939 then BH5 unless BH5 is taken over 265-270MHz...
This is because A64 S939 already as VERY low latencies and high bandwidth, so it is better to have balanced timings/speeds.
Onepagebook
01-06-2005, 04:14 PM
hm. Anything to testify this statement?
DDR500 2-2-2-5 (BH-5) vs DDR600 2.5-3-3-8 1T (G.Skill TCCD)
You mean bandwidth?:D
If so, I would say even DDR550 2-2-2-5 bh-5 can't beat TCCD DDR580 2.5-3-3-6 :)
OPB
skate2snow
01-06-2005, 04:48 PM
I thin he means General Performance since that is what is important... You can have the highest bandwidth, but if it takes an eternity to process, the Bandwidth wont change anything...
amilian
01-06-2005, 10:28 PM
I just switched out my BH5 @ 250fsb used with a 166 divider for TCCD at 300fsb and without question I am MUCH happier with general performance, superpi times, bandwidth, arith, everest latency, read and write etc.. Also, the mem controller on my chip absolutely likes it better. I was having a :banana::banana::banana::banana:ens of a time getting under 35sec superpi stable, and now with TCCD I'm rock solid at 33 seconds. I hit 32sec with 9x290, but when priming she reboots due to chip overheating. Need better cooling....
lol "d1ckens" got the bananas!
bachus_anonym
01-07-2005, 12:26 AM
You mean bandwidth?:D
If so, I would say even DDR550 2-2-2-5 bh-5 can't beat TCCD DDR580 2.5-3-3-6 :)
OPB
from my testing, i need about 25-30Mhz more with 8-3-3-2.5 1T to beat 6-2-2-2.0 1T.... this is all fine 'n dandy as soon as i could get TCCD to run @ DDR580 "full stable" with no dividers. once i would hit 166 divider mem would go down to DDR480-500 bearing upgrade to TCCD useless for my setup as i can beat that with my 1GB VX ;)
so is there anyone that has any "prime" screenies with GSkill @ DDR580-600 on Neo2 ???
Onepagebook
01-07-2005, 10:16 AM
from my testing, i need about 25-30Mhz more with 8-3-3-2.5 1T to beat 6-2-2-2.0 1T.... this is all fine 'n dandy as soon as i could get TCCD to run @ DDR580 "full stable" with no dividers. once i would hit 166 divider mem would go down to DDR480-500 bearing upgrade to TCCD useless for my setup as i can beat that with my 1GB VX ;)
so is there anyone that has any "prime" screenies with GSkill @ DDR580-600 on Neo2 ???
I think windwithme does. :)