View Full Version : CH-5 Memory
Noktar
10-26-2004, 01:40 AM
How high u pushed your CH-5 sticks.
Yesterday I tested my XMS3200CD 1.2
And I got 3D Mark/SuperPi stable 230Mhz 2,3,3,11 with 2.9V
Is this good or bad ?
Reflex1
10-26-2004, 01:44 AM
its ok, can u lower your timings any more or not? some godly CH-5 do 2-2-2-5. What hapens if u put more volts into em? (3.2v)
I get 240 2/2/2/6 3.2v with mine (OCZ 3500EL). They needed days of burn in when I got them though.
stestan
10-26-2004, 02:21 AM
I got 2x256 no name ch/5 does 249 5-2-2-2 (1-1) with 3.3v but 250 and my windows gets corrupted :censored:
Gokou
10-26-2004, 07:45 AM
could do 227 @ 11-2-2-2 with mine @ 2.7v but didnt seem to like any higher voltage :(
sobol
10-26-2004, 09:15 AM
You tun your ram with 1T or 2T ?
mad mikee
10-26-2004, 09:51 AM
On my infinity, used to get 243 FSB prime (24hrs) 3d2k1, etc solid stable on CH5 10-2-2-2 1T @ 3.2 V. Would lock up in A64 for me, so they went w/ the infinity. :rolleyes:
Highland3r
10-26-2004, 10:07 AM
OCZ EL, 235 2.5,2,2,11 on 3.0v atm, seem stable, but as mentioned above they seem to need a good burn in...
They also HATED the NF7, couldnt get them above 225 on the same timings with more voltage, no matter what bios :S
My Geil PC3200 (probably CH-5) can do stable 3DMark01 and Pi 1M(only tested for now) 240mhz 1:1(x12 multi, x3 htt) CL2.2.2.0.13.16 T1 @ 3.5v. Perhaps after grilling them for some time, they could do 250mhz 1:1 with same settings. That would remove the need to upgrade to DDR500 Ballistix, I guess...
Just discovered the stick could do those timings at that speed. Those are very good timings right?
The stick is a 512mb one from a Kingston DC Kit. I still have the other one, but it hasn't been tested yet.
EDIT: They can do 1M at 242mhz max for now. Screnshot at 240mhz:
http://server5.uploadit.org/files/nexus2525-240mhz.jpg
Formann
10-26-2004, 11:17 PM
2x512 Corsair XMS3200LL v1.2
210 2-3-2-6 @ 2.85v
214 2.5-3-3-6 @ 2.85v
These sticks cost 3000.- NOK (~300$) (Not even worth half of that)
Total WASTE of money... :mad:
STEvil
10-26-2004, 11:27 PM
200 1.5-2-2-11 2.6v so far, 2x512. Havent had a platform capable of past 200fsb to test them yet.. but my LP-UT just came in :D
I get 240 2/2/2/6 3.2v with mine (OCZ 3500EL). They needed days of burn in when I got them though.
What program is good for ram burn in? What did you use and at what setting? I have that DFI bios with that memtest program build in. Is that a good program to do it in? If yes, what settings/tests should I run, that'll be best for burn in?
I want mine to do 249mhz CL2.2.2.0 T1, but they can only do Pi M4/3DMark01 at 242mhz for now :D
mine CH-5 did 240 cpc on 2-2-2-11 3.3vdimm hehe
ColdFlare
10-27-2004, 10:30 AM
I got 2x256 no name ch/5 does 249 5-2-2-2 (1-1) with 3.3v but 250 and my windows gets corrupted :censored:
My memory behaves the same as yours. 2x256 ch-5 does 249 2-5-2-2 at 3.2volts totally stable in Memtest. But once I get 250 it errors in memtest. Even if I increase the voltage to 3.3 it errors. If I run at the most relax settings it still crashes at 250. Sucks, dunno whats holding me back. These sticks cost me 100 bucks 1 year ago.
sobol
10-27-2004, 10:35 AM
I got problem with them , exacly with CPC on.
My A64 NC maxout at 2360 mhz.
Now:
Mem 240 mhz 2-2-2 1T , CPU Below 1900 mhz , all works fine stable at all tests.
Mem 236 mhz 2-2-2-2T , CPU 2360 mhz , all works fine stable at all tests.
Mem 200-240 2-2-2-1T , Cpu 2000-2360 mhz non stable , fail in all tests.
My settings are 1.76 vcore, 1.8 chipset, 3.3 vdimm( bios jump from 3.19 to 3.22v ).
Anyone have idea ?
fareastgq
10-27-2004, 04:08 PM
I got problem with them , exacly with CPC on.
My A64 NC maxout at 2360 mhz.
Now:
Mem 240 mhz 2-2-2 1T , CPU Below 1900 mhz , all works fine stable at all tests.
Mem 236 mhz 2-2-2-2T , CPU 2360 mhz , all works fine stable at all tests.
Mem 200-240 2-2-2-1T , Cpu 2000-2360 mhz non stable , fail in all tests.
My settings are 1.76 vcore, 1.8 chipset, 3.3 vdimm( bios jump from 3.19 to 3.22v ).
Anyone have idea ?
that's wierd, I have 2x512 xms pro, I can hit 300 fsb on lanpartyGB @ 2 2 2 timings, 3.4 volts mind you. :) it's not just pretty lights, hehe. cpc on btw. 1.9 vdd, ocz booster, and 1.7 vcore
sobol
10-27-2004, 04:17 PM
Screanshot, i dont belive its CH5
STEvil
10-27-2004, 09:20 PM
its not, and he's definately not doing 300fsb 1:1 unless its hyinx or samsung which definately rules out 2-2-2 above 230.
3.4v is only enough for about 260 even on the best of bh/ch chips anyways.
fareastgq
10-27-2004, 09:36 PM
sure it is, it wouldn't run 2 2 2 timings at 3 volts or lower, only 3 2 2, I don't have the UTGB board anymore, it wasn't mine, but I am running 2 2 2 on my nf7-s. vdd mod and my cpu is limiting my fsb on this board though. Somone even took off the spreaders, you can go to corsair's website and confirm this yourself :)
STEvil
10-27-2004, 10:20 PM
sorry, still dont believe you.
MUCHO
10-28-2004, 12:14 AM
I got a stick of CH5 that does 220 2 3 2 at 2.8 - won't go any higher even at 3.2 volts...
Mauri Antero
10-28-2004, 02:11 AM
Muskin level one pc3500 ch-5, yesterday just for fun did some tests.
Max fsb 255 in dual with desent tight memory timing and 3.4V
mine 2x512mb 1.5-3-2-10 1T 253mhz 3.1v
fareastgq
10-28-2004, 05:05 AM
like I said, you don't have to believe me, when I get another board I'll post up some screenies if someone wants to host them. no big deal. I have XMS ram, not XL. they are not samsung chips.
Formann
10-28-2004, 01:12 PM
2x512 Corsair XMS3200LL v1.2
210 2-3-2-6 @ 2.85v
214 2.5-3-3-6 @ 2.85v
These sticks cost 3000.- NOK (~300$) (Not even worth half of that)
Total WASTE of money... :mad:
Did some more testing with my MSI 865PE
239 2.5-3-2-6 DC @ 3.2v in bios. memteststable.
fareastgq:
Running 300 2-2-2/3-2-2 @ 3.4vdimm with Corsair is not even remotely probable.
Not even half multi on A64 will get you that.
fareastgq
10-28-2004, 05:01 PM
jeez you guys, I'll post up some damn screenies when I get another board. and why is it not possible? I have a ocz booster, I can run up to 4.0 if I want, boggle. Do you have a couple sticks of xms pro's? I'm talking from experience, not some BS I read. Many ppl have gotten 300 HTT on a lanpartyGB. The guy that you just posted about, either you have some crap sticks, or your board is screwed. you can always rma them and get some new ones. Corsair ain't no joke and you didn't test it with a lanparty + booster, you tested with an msi.
enzoR
10-28-2004, 05:08 PM
hes saying its impossible with 3.4 v....
STEvil
10-28-2004, 05:24 PM
Yes, lots of people have hit 300HTT+
NONE were using CH-5 and NONE have been very far past 300 with better than 2.5-3-3-7 timings with more than 1x512mb ram.
In fact, nobody has ever had a Winbond based stick of ram at 300mhz on AMD to the best of my knowledge, and certainly not at 3.4v.
fareastgq
10-28-2004, 06:59 PM
welp, guess I'm about to post some screenies then ;) I'll show you guys the power of super burned in ch-5 :) Like I said, just becuase no one has ever done it that anyone here has seen, doesn't mean it hasn't been done, Might not be till around christmas or so, I can't decide if I wanna get another 754 board or a 939 board....built a 754 dfi and 939 msi.. the 939 seemed to feel faster irl...
are you sure you're running 1:1 ?
what multi do you have?
cpc on/off?
cause ch5 @ 300mhz is next to impossible.
wampir
11-01-2004, 05:31 PM
Is ch5 beter than hynix d43 for A64 ?? 2x512
Which one should I take ???
tictac
11-01-2004, 05:52 PM
236MHz 2-2-2-11 3.1V - Stable
242MHz 2-2-2-11 3.2V - benchable
:banana:
wampir
11-01-2004, 06:51 PM
which mobo ???
I'am considering DFI LP nf3 and buffalo 3200 ch5
Muskin level one pc3500 ch-5, yesterday just for fun did some tests.
Max fsb 255 in dual with desent tight memory timing and 3.4V
holly :banana::banana::banana::banana: this is kickass ram...newegg still has it .....but expensive around 290$ for 2*512...
tictac
11-02-2004, 02:03 AM
which mobo ???
I'am considering DFI LP nf3 and buffalo 3200 ch5
on ABIT NF7-S Rev2.0
it should do better with DFI setup i assume :toast:
STEvil
11-10-2004, 12:32 AM
While we wait on that guys reply, here is something to keep us soothed.
Did this a couple hours ago on my A64 2800+ Clawhammer (CG).
2x512 Buffalo PC3200 (0343WI CH-5) @ 245mhz 1.5-2-2-10-12-16 1T 3.30v (measured with DMM). Not bad at all :toast:
HITAC
11-10-2004, 12:37 AM
2x512MB Kingston HX 3500K2 (CH5) @ 250 MHz 2-2-2-5 3,25V
(DFI LP nf3 :D )
omg CH-5 doing almost as BH-5/6
STEvil
11-10-2004, 01:22 AM
almost? i'd put it on par.
Its only fault is that it doesnt work as well with 865/875p as BH does.
STEvil
11-10-2004, 01:32 AM
you mean the 260fsb bug? I think that was just a bios bug and boards since then have resolved the issue.
sluggard
11-10-2004, 04:12 AM
benched mine@260MHz 3.4v w. DDR-booster on sempron 3100+ and DFI nf3 UT250GB
http://pk.robotron.ee/260.jpg
Shroomalistic
11-10-2004, 04:51 AM
Heres some ch-5 lovin for ya with my gig of patriot 3200LL
http://home.comcast.net/~shrmytoon/ch5_265_tight.gif
http://home.comcast.net/~shrmytoon/ch5_sandra_260.gif
PDP LL is CH-5 ? shroom where do you get all the ram for testing ? :D
Shroomalistic
11-10-2004, 04:14 PM
PDP LL is CH-5 ? shroom where do you get all the ram for testing ? :D
The Patriot 3200LL I bought about a year ago or more
The old Winbond bh-5 that I had, I bought at fry's at the begining of last year
The Kingston 3000 I bought about a year ago too
the Kingston 3500 is the stuff that Pc Ice bought about 2 years ago when it first came out and we split em, he had 1 and I had one. I gave him my stick and he gave me the money to buy that old winbond bh-5 above
The TCCD that ive been playing with is also Pc Ice's that he got from centon.
The Hynix D5's are Pc Ice's, Opp gave them to him.
The Twinmos 3700 was donated to me by Nomjr
I think thats all of it, might be more laying around somewhere. But most of it was bought from Fry's
JetForcegeminiX
11-10-2004, 06:29 PM
i cna bench a 245 2-2-2-5 and screenshot at 250 mhz on my level 1 mushkins at 3.3 volts
fareastgq
02-14-2005, 10:47 PM
ok guys, I can finally do some decent testing, I couldn't wait for dfi 939 agp board anymore, I ordered an ultra-d, some ch-5 goodness coming your way soon :) timings I'll do for my ch-5 are 2.5 3 3 8, 2 3 3 8, 2 2 2 8, 1 stick and 2 stick tests. I'll finally see what they run stable at 24/7. I can't post screenies, but if someone wants to host them I can :P
krampak
02-15-2005, 01:21 AM
I've 2x256 Buffalo with CH5 0405WM chips. It does 260 2-2-2 with 3'6V and 240 1'5-2-2 with 3'2V.
blinky
02-15-2005, 02:01 AM
that's wierd, I have 2x512 xms pro, I can hit 300 fsb on lanpartyGB @ 2 2 2 timings, 3.4 volts mind you. :) it's not just pretty lights, hehe. cpc on btw. 1.9 vdd, ocz booster, and 1.7 vcorenope sorry, just isnt possible...
either ur using a mem divider, or 0.5 multi... or lying about the timings... or somethign... post up some screenies well see for ourselves
saboya
02-15-2005, 02:28 AM
300 2-2-2 3.4v
that's just impossible.
.::$k4T4N::.
02-15-2005, 05:21 AM
whats it about burn in???
shall ich put 3,2 V on my twinmos ch-5 and the run the sandra
burn in and then oc more??? :slobber:
my are doing 220fsb @ 2,9V on NF7 (maybe more)
why is my oc so much lower than yours???
longsiew
04-22-2005, 10:33 PM
My TwinMos SP UTT is at DDR500 (2-2-2-5) @ 3.5V on DFI NF4 ultra-D @1.475v(vcore). I burn-in my RAM at DDR 460 @ 3.3v for 5 hours or more (using Prime 95). Currently, I am burn-in my RAM @ DDR 506 @ 3.5v (using memtest v1.55). I will try to oc tonignt to DDR 510
FiNcH64
06-25-2005, 06:13 PM
hi guys, i own a pair of muskin level one pc3500 1gb kit, and they are CH-5 checked down on the new ram list thread hehe...
i was amazed when i decided to use 2 80mm coolermaster fans, and my surprised was that i reach 260mhz with 2 3 2 6 latencys at 3.45 v.. and actually found out that i can reach even higher, but i don't need right now cause my crappy winchester can't reach more than 2.6 ghz on air hehe..
so here is my validation, my name is andres so thats why it didnt appear like finch..
tell me what you think about it
cheers :toast: cpu-z validation (http://valid.x86-secret.com/show_oc?id=24813)
Below Ambient
06-25-2005, 06:27 PM
ch-5 is ok, but at 2.9v i would suspect a bit more mhz would be availlbe